• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.115-121
• /
• 2013

We fabricated thin film transistors (TFTs) using TiInZnO(TiIZO) thin films as active channel layer. The thin films of TiIZO were deposited at room temperature by RF-magnetron co-sputtering system from InZnO(IZO) and Ti targets. We examined the effects of titanium addition by X-ray diffraction, X-ray photoelectron spectroscopy and the electrical characteristics of the TFTs. The TiIZO TFTs were investigated according to the radio-frequency power applied to the Ti target. We found that the transistor on-off currents were greatly influenced by the composition of titanium addition, which suppressed the formation of oxygen vacancies, because of the stronger oxidation tendency of Ti relative to that of Zn or In. A optimized TiIZO TFT with rf power 40W of Ti target showed good performance with an on/off current ratio greater than $10^5$, a field-effect mobility of 2.09 [$cm^2/V{\cdot}s$], a threshold voltage of 2.2 [V] and a subthreshold swing of 0.492 [V/dec.].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.123-123
• /
• 2008

In this work, amorphous carbon thin films were deposited for hard mask applications by a reactive particle beam (RPB) assisted sputtering system at room temperature. The depositing characteristics of the films were investigated as functions of operating parameters such as reflector bias voltage and RF plasma power. It was confirmed that the deposition rate increased with increasing the reflector bias voltage and RF plasma power. By an atomic force microscope (AFM), it was revealed that the surface roughness was also increased. The total stress in films was determined by the use of the substrate curvature and its result will be discussed.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.10a
• /
• pp.68-71
• /
• 2006

Multi-component $ZnO-In_2O_3-SnO_2$ thin films have been prepared by RF magnetron co-sputtering using targets composed of $In_3Sn_4O_{12}$(99.99%) [1] and ZnO(99.99%) at room temperature. $In_3Sn_4O_{12}$ contains less In than commercial ITO, so that it lowers cost. Working pressure was held at 3 mtorr flowing Ar gas 20 sccm and sputtering time was 30 min. RF power ratio [RF1 / (RFI + RF2)] of two guns in sputtering system was varied from 0 to 1. Each RF power was varied $0{\sim}100W$ respectively. The thickness of the films was $350{\sim}650nm$. The composit ion concentrations of the each film were measured with EPMA, AES and XPS. The low resistivity of $1-2\;{\times}\;10^3$ and an average transmittance above 80% in the visible range were attained for the films over a range of ${\delta}\;(0.3\;{\leq}\;{\delta}\;{\leq}\;0.5)$. The films also showed a high chemical stability with time and a good uniformity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.72-77
• /
• 2013

The effect of sputtering condition on the structural properties of ZnO thin films grown by RF magnetron sputtering system was investigated for TFT driver circuit. ZnO thin films were grown with ZnO target varying RF power and working pressure. Structural properties were investigated by X-ray diffraction (XRD) and atomic force microscope (AFM). The ZnO thin films have sufficient crystallinity on the 100W RF power. But, the surface roughness of ZnO films was increased as increased RF power. As increased working pressure from 5 mTorr to 15 mTorr, a full width at half maximum (FWHM) of ZnO (002) peak was increased.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.73-78
• /
• 2004

AIN thin film has been deposited on the $AI_2$$O_3$substrate with reactive radio frequency( RF) magnetron sputtering method. In this work, elelctromechanical coupling coefficient of AIN thin film was increased with an increase of AIN thin film thickness, and the maximum value was 0.11%. Insertion loss of SAW device was decreased with an increase of AIN thin film thickness and the minimum value was 33［㏈］. SAW velocity of IDTs/AIN/$AI_2$$O_3$structure and IDTs/AIN/$AI_2$$O_3$/Si structure were about 5480［㎧］and 5040［㎧］respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.450-453
• /
• 2020

In this study, ZnO:Ga thin films were fabricated on a glass substrate using various Ar flows by an RF magnetron sputter system at room temperature. The dependencies of Ar flow on different properties were investigated. An appropriate control over the Ar flow led to the formation of a high-quality thin film. The ZnO:Ga films were formed as a hexagonal wurtzite structure with high (002) preferential orientation. The films exhibited a typical columnar microstructure and a smooth top face. The average transmittance was 85~89% within the visible area. By decreasing the Ar flow, the sheet resistance was decreased due to an increase in the grain size and a decrease in the root mean square roughness. The lowest sheet resistance of 86 Ω/□ was obtained at room temperature for the 40 sccm Ar flow.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.6-9
• /
• 2010

Surface properties of polytetrafluoroethylene(PTFE) films fabricated by rf-magnetron sputtering system with UV surface treatment were investigated to increase water contact angle for their hydrophobic property. We found that the surface morphology and water contact angles of PTFE film modified as a function of the UV treatment times using UV-irradiation were influenced. The water contact angle of PTFE film with optimized UV treatment time for 15 minute showed a high hydrophobicity compared with the film without any surface treatment. We thought that it was due to the energy change of PTFE surface with an adhesion improvement to the glass surface as a smoothing a rough surface with needle-shape and/or the enhancement of an interface property as a removing some defects on the surface like a cleaning effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.97-98
• /
• 2005

To investigate the ZnO thin films which is interested in the next generation of short wavelength LEDs and Lasers, our ZnO thin films were deposited by RF sputtering system. Phosphorus (P) and arsenic (As) were diffused into about 2.1${\mu}m$ ZnO thin films sputtered by RF magnetron sputtering system mn ampoule tube which was below $5\times10^{-7}$ Torr. The dopant sources of phosphorus and arsenic were $Zn_3P_2$ and $ZnAs_2$. Those diffusion was perform at 500, 600, and 700$^{\circ}C$ during 3hr. We find the condition of p-type ZnO whose diffusion condition is 700$^{\circ}C$, 3hr Our p-type ZnO thin film has not only very high carrier concentration of above $10^{19}/cm^3$ but also low resistivity of $5\times10^{-3}{\Omega}cm$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.323-324
• /
• 2007

Investigation of improving the properties of UV photodetector which uses the wide bandgap of ZnO are under active progress. In this paper, transparent conducting aluminum-doped Zinc oxide films(AZO) were prepared by rf magnetron sputtering on glass(corning 1737) and p-Si substrate, were then annealed at temperature $400^{\circ}C$ for 2hr. The AZO thin films were deposited by RF sputtering system. HF power and work pressure is 120 W and 15 mTorr, respectively, and the purity of AZO target is 5N. The AZO thin films were deposited at 300, 400, $500^{\circ}C$, and $600^{\circ}C$. For sample deposited at $400^{\circ}C$, we observed best $V_r-I_{ph}$ of 0.94 mA and good transmittance.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.407-410
• /
• 2012

The properties of Al-doped ZnO (AZO) films were investigated as a function of H2/(Ar + H2) gas ratio using an AZO (2 wt% Al2O3) ceramic target in a radio frequency (RF) magnetron sputtering system. The deposition process was done at 200 ℃ and in 2 × 10-2Torr working pressure and with various ratios of H2/(Ar + H2) gas. During the AZO film deposition process, partial H2 gas affected the AZO film characteristics. The electron resistivity (~ 9.21 × 10-4 Ωcm) was lowest and mobility (~17.8 ㎠/Vs) was highest in AZO films when the H2/(Ar + H2) gas ratio was 2.5%. When the H2/(Ar + H2) gas ratio was increased above 2.5%, the electron resistivity increased and mobility decreased with increasing H2/(Ar + H2) gas ratio in AZO films. The carrier concentration increased with increasing H2/(Ar + H2) gas ratio from 0% to 7.5%. This phenomenon was explained by reaction of hydrogen and oxygen and additional formation of oxygen vacancy. The average optical transmission in the visible light wavelength region over 90% and an orientation of the deposition was [002] orientation for AZO films grown with all H2/(Ar + H2) gas ratios.