• 한국재료학회지
• /
• 제20권5호
• /
• pp.267-270
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Cu/ITO (ICI) multilayer films were prepared on glass substrates with a reactive radio frequency (RF) magnetron sputter without intentional substrate heating, and then the influence of the Cu interlayer on the methanol gas sensitivity of the ICI films were considered. Although both ITO and ICI film sensors had the same thickness of 100 nm, the ICI sensors had a sandwich structure of ITO 50 nm/Cu 5 nm/ITO 45 nm. The ICI films showed a ten times higher carrier density than that of the pure ITO films. However, the Cu interlayer may also have caused the decrement of carrier mobility because the interfaces between the ITO and Cu interlayer acted as a barrier to carrier movement. Although the ICI films had two times a lower mobility than that of the pure ITO films, the ICI films had a higher conductivity of $3.6{\cdot}10^{-4}\;{\Omega}cm$ due to a higher carrier density. The changes in the sensitivity of the film sensors caused by methanol gas ranging from 50 to 500 ppm were measured at room temperature. The ICI sensors showed a higher gas sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the ICI film sensors have the potential to be used as improved methanol gas sensors.

• 한국재료학회지
• /
• 제17권11호
• /
• pp.574-579
• /
• 2007

Amorphous $BaTi_4O_9$ ($BT_4$) film was deposited on Pt/Si substrate by RF magnetron sputter and their dielectric properties and electrical properties are investigated. A cross sectional SEM image and AFM image of the surface of the amorphous $BT_4$ film deposited at room temperature showed the film was grown well on the substrate. The amorphous $BT_4$ film had a large dielectric constant of 32, which is similar to that of the crystalline $BT_4$ film. The leakage current density of the $BT_4$ film was low and a Poole-Frenkel emission was suggested as the leakage current mechanism. A positive quadratic voltage coefficient of capacitance (VCC) was obtained for the $BT_4$ film with a thickness of <70 nm and it could be due to the free carrier relaxation. However, a negative quadratic VCC was obtained for the films with a thickness ${\geq}96nm$, possibly due to the dipolar relaxation. The 55 nm-thick $BT_4$ film had a high capacitance density of $5.1fF/{\mu}m^2$ with a low leakage current density of $11.6nA/cm^2$ at 2 V. Its quadratic and linear VCCs were $244ppm/V^2$ and -52 ppm/V, respectively, with a low temperature coefficient of capacitance of $961ppm/^{\circ}C$ at 100 kHz. These results confirmed the potential suitability of the amorphous $BT_4$ film for use as a high performance metal-insulator-metal (MIM) capacitor.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.315-316
• /
• 2012

반도체와 금속배선의 확산을 방지하기 위한 확산방지막의 필요성이 대두되고 있으며, 이에 대한 연구는 많은 연구 그룹에서 진행중에 있다. 하지만 이러한 연구의 대부분은 전기적, 결정학적 특성에 대하여 안전성 및 재료학적 연구에 국한되어 진행되어졌다. 본 연구그룹은 텅스텐(W)을 질화시킨 W-N 확산방지막에 대하여 연구를 진행하였고, 역시 결정학적 특성에 대한 열적인 안전성을 주로 연구하였으나, 본 연구에서는 W-N 박막의 나노영역에 대한 기계적 특성 평가에 주안점을 두어 W-N 박막의 stress를 nano-indenter 기법을 이용하여 측정하고자하였다. 특히 공정시간의 단축 효과 등의 이유로 박막의 두께를 감소시키는 현재 추세에 맞춰 더 얇은 W-N 확산방지막을 제작하였으며, 이에 대한 분석을 실시하였다. W-N 확산방지막은 Ar(Argonne), $N_2$ (nitrogen) 총유량을 40 sccm으로 고정하여, 질소 유입 조건을 0, 0.5, 1 sccm 으로 변화시켜 Si (silicon) (100) 기판 위에 rf (radio-frequency) magnetron sputter를 이용하여 증착하였다. 이때 W-N 박막의 두께를 30, 100 nm로 달리하여 증착하였으며, 증착된 박막은 질소 분위기 $600^{\circ}C$에서 30분간 열처리하였다. 증착된 시료는 nano-indent를 통하여 표면으로부터 10 nm 부근의 극 표면 물성을 측정하였다. 측정 결과, $N_2$ 가스의 유량을 0.5 sccm 흘려주면서 증착한 W-N 박막이 $N_2$가스를 흘려주지 않은 W 박막과 비교하여 압축응력을 덜 받아 비교적 열에 대하여 안정적임을 확인하였다. 또 30 nm 두께의 W-N 박막이 100 nm 두께의 W-N 박막보다 더 기계적으로 안정적인 상태임을 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.341-341
• /
• 2012

Recently, oxide semi-conductor materials have been investigated as promising candidates replacing a-Si:H and poly-Si semiconductor because they have some advantages of a room-temperature process, low-cost, high performance and various applications in flexible and transparent electronics. Particularly, amorphous indium-gallium-zinc-oxide (a-IGZO) is an interesting semiconductor material for use in flexible thin film transistor (TFT) fabrication due to the high carrier mobility and low deposition temperatures. In this work, we demonstrated improvement of flexibility in IGZO TFTs, which were fabricated on polyimide (PI) substrate. At first, a thin poly-4vinyl phenol (PVP) layer was spin coated on PI substrate for making a smooth surface up to 0.3 nm, which was required to form high quality active layer. Then, Ni gate electrode of 100 nm was deposited on the bare PVP layer by e-beam evaporator using a shadow mask. The PVP and $Al_2O_3$ layers with different thicknesses were used for organic/inorganic multi gate dielectric, which were formed by spin coater and atomic layer deposition (ALD), respectively, at $200^{\circ}C$. 70 nm IGZO semiconductor layer and 70 nm Al source/drain electrodes were respectively deposited by RF magnetron sputter and thermal evaporator using shadow masks. Then, IGZO layer was annealed on a hotplate at $200^{\circ}C$ for 1 hour. Standard electrical characteristics of transistors were measured by a semiconductor parameter analyzer at room temperature in the dark and performance of devices then was also evaluated under static and dynamic mechanical deformation. The IGZO TFTs incorporating hybrid gate dielectrics showed a high flexibility compared to the device with single structural gate dielectrics. The effects of mechanical deformation on the TFT characteristics will be discussed in detail.

• 한국재료학회지
• /
• 제12권4호
• /
• pp.296-303
• /
• 2002

For potential application to quantum mechanical devices, nano-composite thin films, consisting of GaAs quantum dots dispersed in SiO$_2$ glass matrix, were fabricated and studied in terms of structural, chemical, and optical properties. In order to form crystalline GaAs quantum dots at room temperature, uniformly dispersed in $SiO_2$matrix, the composite films were made to consist of alternating layers of GaAs and $SiO_2$in the manner of a superlattice using RF magnetron sputter deposition. Among different film samples, nominal thickness of an individual GaAs layer was varied with a total GaAs volume fraction fixed. From images of High Resolution Transmission Electron Microscopy (HRTEM), the formation of GaAs quantum dots on SiO$_2$was shown to depend on GaAs nominal thickness. GaAs deposits were crystalline and GaAs compound-like chemically according to HRTEM and XPS analysis, respectively. From measurement of optical absorbance using a spectrophotometer, absorption edges were determined and compared among composite films of varying GaAs nominal thicknesses. A progressively larger shift of absorption edge was noticed toward a blue wavelength with decreasing GaAs nominal thickness, i.e. quantum dots size. Band gaps of the composite films were also determined from Tauc plots as well as from PL measurements, displaying a linear decrease with increasing GaAs nominal thickness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.389-389
• /
• 2013

HfOx (Hafnium oxide)는 ~25의 고유전상수, 5.25 eV의 비교적 높은 Band-gap을 갖는 물질로 MOSFET (metal-oxide semiconductor field-effect-transistor) 구조의 Oxide 박막을 대체 가능한 물질로 연구가 지속되고 있다. 현재까지 진행된 대다수의 연구는 증착 조건에 따른 박막의 결정학적 및 전기적 특성에 대한 주제로 진행되었고 다양한 연구 결과가 보고된바 있다. 하지만 기존의 연구 기법은 박막의 nanomechanics 특성에 대한 연구가 부족하여 이를 보완하기 위한 연구가 절실하다. 따라서 본 연구에서는 HfOx 박막 내 포함된 산소가 고온 열처리 과정에서 빠져나감으로 인한 박막의 nanomechanics 특성을 확인하고자 하였다. 시료는 rf magnetron sputter를 이용하여Si (silicon) 기판위에 Hafnium target으로 산소유량(5, 10, 15 sccm)을 달리하여 증착하였고, 이후 furnace에서 $400^{\circ}C$에서 $1,000^{\circ}C$까지 질소분위기에서 20분간 열처리를 실시하였다. 실험결과 시료의 전기적 특성을 I-V 곡선을 측정하여 확인하였고, 증착 시 산소 유량이 5 sccm에서 15 sccm으로 증가함에 따라서 누설전류 특성은 급격히 향상되었고, 열처리 온도가 증가함에 따라 감소하는 특성을 나타내었다. 또한 시료의 nanomechanics 특성을 확인하기 위하여 nano-indenter를 이용하여 시료의 표면강도(surface hardness)와 탄성계수(elastic modulus)를 확인하였다. 측정결과 5 sccm 시료의 표면강도와 탄성계수는 상온에서 열처리 온도가 증가함에 따라 각각 7.75 GPa에서 9.19 GPa로, 그리고 133.83 GPa에서 126.64 GPa로 10, 15 sccm의 박막의 비하여 상대적으로 균일한 특성을 나타내었다. 이는 증착 시 박막 내 과포화된 산소가 열처리 과정에서 빠져나감으로 인한 것이며, 또한 과포화된 정도에 따라 더 적은 열처리 에너지에 의하여 박막을 빠져나감으로 인한 것으로 판단된다. 또한 열처리 과정에서 산소가 빠져나가는 상대적인 flux의 영향으로 인하여 박막의 mechanical한 균일도의 변화가 나타났다.

• 한국표면공학회지
• /
• 제47권2호
• /
• pp.75-80
• /
• 2014

Nanocrystalline diamond(NCD) films on steel(SKH51) has been investigated using SiC interlayer film. SiC was deposited on SKH51 or Si wafer by RF magnetron sputter. NCD was deposited on SiC at $600^{\circ}C$ for 0.5~4 h employing microwave plasma CVD. Film morphology was observed by FESEM and FIB. Film adherence was examined by Rockwell C adhesion test. The growth rate of NCD on SiC/Si substrate was much higher than that on SiC/SKH51. During particle coalescence, NCD growth rate was slow since overall rate was determined by the diffusion of carbon on SiC surface. After completion of particle coalescence, NCD growth became faster with the reaction of carbon on NCD film controlling the whole process. In the case of SiC/SKH51 substrate, a complete NCD film was not formed even after 4 h of deposition. The adhesion test of NCD/SiC/SKH51 samples revealed a delamination of film whereas that of SiC/SKH51 showed a good adhesion. Many voids of less than 0.1 ${\mu}m$ were detected on NCD/SiC interface. These voids were believed as the reason for the poor adhesion between NCD and SiC films. The origin of voids was due to the insufficient coalescence of diamond particles on SiC surface in the early stage of deposition.

• 한국자기학회지
• /
• 제18권1호
• /
• pp.32-35
• /
• 2008

차세대 반도체 산업의 발전을 위하여 반도체 소자의 구조는 DRAM, FRAM, MRAM 등 여러 분야에서 다양한 연구가 진행되고 있다. 특히 이런 차세대 반도체 소자에서 금속 배선으로는 Cu가 사용되며, Cu 금속 배선을 위한 확산방지막에 대한 연구는 반드시 필요하다[1-3]. Cu 금속 배선을 위한 확산방지막에 대한 현재까지의 연구에서는 Tungsten(W)을 기반으로 Nitride(N)를 불순물로 첨가한 확산방지막에 대하여 연구되었다[4-7]. 이러한 W-N를 기반으로 본 연구에서는 물리적 기상 증착법(PVD) 방법인 RF Magnetron Sputter 방법으로 W-N 이외에 Carbon(C) 과 Boron(B)을 첨가하여 확산방지막의 특성을 확인하였고, 특히 Boron Target의 power를 변화하여 W-B-C-N 확산방지막의 Boron에 의한 특성과 열적 안정성을 연구하였다[8-10]. 실험은 다양한 Boron의 조성을 가지는 확산방지막을 증착하여 $\beta$-ray와 4-point probe를 사용하여 확산방지막의 특성을 확인하였고, 고온($700^{\circ}C{\sim}1000^{\circ}C$) 열처리한 후 X-ray Diffraction 분석을 하여 열적 안정성을 확인하였다.

• 한국자기학회지
• /
• 제9권6호
• /
• pp.291-295
• /
• 1999

IrMn을 반강자성체로 사용하고 순수한 Al을 자연산화시켜서 제작한 Al203를 절연층으로 사용한 spin-valve 형태의 NiFe/Co/Al2O3/Co/IrMn 터널링 접합의 자기저항효과를 조사하였다. IrMn의 두께가 약 100$\AA$이상일 경우 강자성체와의 교환상호작용이 발생하기 때문에 NiFe(183$\AA$)/Co(17$\AA$)/Al-oxide(16$\AA$)IrMn(100$\AA$) 터널링 접합에서 자기저항효과가 관찰되며 TMR비(%)는 $\pm$20 Oe의 인가자장에서 10% 이상의 값을 갖는다. 하부 자성층인 NiFe/Co의 길이방향으로 수행한 자장 중 열처리에 의해 저항은 다소 감소하고 TMR비(%)는 열처리온도에 따라 증가하여 20$0^{\circ}C$에서 23%의 최대값을 갖는다. 자성층의 폭을 변호시켜 접합면적을 달리한 시료의 TMR비(%)는 접합면적이 증가할수록 증가하고 저항은 감소한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.277-277
• /
• 2010

The capacity of the carbonaceous materials reached ca. $350\;mAhg^{-1}$ which is close to theorestical value of the carbon intercalation composition $LiC_6$, resulting in a relatively low volumetric Li capacity. Notwithstanding the capacities of carbon, it will not adjust well to the need so future devices. Silicon shows the highest gravimetric capacities (up to $4000\;mAhg^{-1}$ for $Li_{21}Si_5$). Although Si is the most promising of the next generation anodes, it undergoes a large volume change during lithium insertion and extraction. It results in pulverization of the Si and loss of electrical contact between the Si and the current collector during the lithiation and delithiation. Thus, its capacity fades rapidly during cycling. We focused on electrode materials in the multiphase form which were composed of two metal compounds to reduce the volume change in material design. A combination of electrochemically amorphous active material in an inert matrix (Si-M) has been investigated for use as negative electrode materials in lithium ion batteries. The matrix composited of Si-M alloys system that; active material (Si)-inactive material (M) with Li; M is a transition metal that does not alloy with Li with Li such as Ti, V or Mo. We fabricated and tested a broad range of Si-M compositions. The electrodes were sputter-deposited on rough Cu foil. Electrochemical, structural, and compositional characterization was performed using various techniques. The structure of Si-M alloys was investigated using X-ray Diffractometer (XRD) and transmission electron microscopy (TEM). Surface morphologies of the electrodes are observed using a field emission scanning electron microscopy (FESEM). The electrochemical properties of the electrodes are studied using the cycling test and electrochemical impedance spectroscopy (EIS). It is found that the capacity is strongly dependent on Si content and cycle retention is also changed according to M contents. It may be beneficial to find materials with high capacity, low irreversible capacity and that do not pulverize, and that combine Si-M to improve capacity retention.