• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.1
• /
• pp.8-13
• /
• 2022

This paper investigates the method to implement a RF (Radio Frequency) energy harvesting sensor node and to build a sensor network using a CATV network and a leaky coaxial cable. The power supply of a sensor node is designed with the WPTS (Wireless Power Transfer System) receiver operating at 915MHz. A sensor network has limited coverage by the loss of RF signal at a wireless transmission link. The paper proposes to build a sensor network that the BLE signal of a sensor and the signal of a WPTS power transmitter are transmitted through a coaxial cable of a CATV network by utilizing WOC (WiFi over Coax) technology and radiates at a leaky coaxial cable. The length of a leaky coaxial cable and the total loss of a wire link are allowed to the point that the RSSI of a sensor node is more than the minimum value (-78dBm) and lead to extend wireless coverage.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.3
• /
• pp.246-252
• /
• 2013

This paper presents method to suppress signal interference by using the filter in the RF output stage of the radiation equipment as a way to avoid interference between the RF(Radio Frequency) equipment mounted on aircraft. Especially filter design to suppress harmonics of the radiation equipment and testing method to verify the filter's performance is presented. Filter was installed at RF output stage of U/VHF radio in order to prevent interference between U/VHF(Ultra/Very High Frequency) radio and data link system. Filter design and testing method in this paper will be able to give help in the design of aircraft equipments as a tool that can be used to establish measures for problem of interference in the aircraft.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.195-199
• /
• 2003

BEE 802.11 Wireless LAN protocol uses fixed transmission power. It does not consider a power control mechanism based on the distance between the transmitter and the receiver in order to improve overall channel utilization. In home environment, where stations generally lie around an AP, the AP is subject to use transmission power more than it needs. And wireless LAN stations may require different minimal desired received power. If there are many adjacent BSSs in densely populated WLAN area, they might cause RF interference to one another. In this paper we focus on the improvement of aggregate utilization by mitigating RF interference among BSSs. We show that RF interference by APs can be reduced by controlling transmission power using Link Margin information. The reduced interference will then lead to the increased aggregate throughput which is efficient resource utilization.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.5
• /
• pp.409-416
• /
• 2017

In order that multiple wideband RF transmitters which have mission to deliver essential information to aircraft operate at the same time, RF transmitter has a variable sub-carrier frequency to modulate the signal. In case of exposure to weak environment, Wide-band RF transmitter is designed to check component of transmitter that includes antenna BIT to increase system reliability. Normally, Antenna BIT measure the reflection RF power of antenna to check system condition. However, Antenna BIT has a difference that depends on testing frequency to use the long RF cable which is located between the power amp and the antenna. The periodic phenomenon of the reflected antenna power are theoretically explained about dependence on the RF cable length. Based on presented result, suggested measurement methods is effectively able to be applied to diagnosis system condition.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.5
• /
• pp.681-687
• /
• 2017

This paper presents about an implementation of Video Transmitting and Receiving System(VTRS) for acquiring test data. The VTRS consists of two parts. The first is Transmitter Unit(TU) that is installed on a missile to acquire various kinds of data and transmit the data to the ground through RF signals. The second is Receiver Unit(RU) that receives the transmitted RF signals and reconstruct those to the original data. To gather a high speed data reliably and securely on the ground, the TU is designed by considering data transfer scheme, data compression, modulation method, encryption technic, link budget, and antenna radiation pattern. Further, a placement method of multiple receiving stations is suggested. The VTRS has been tested on a field to check the link margins and maximum receiving distance in a real environment. Finally, the VTRS is applied to a missile flight test and gathered high speed data reliably.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.8 no.2
• /
• pp.76-81
• /
• 1983

PCM-NRZ/FM Telemetry system is constructed on the basis of RF link with FM modulatedand NRZ-L binary coded PCM data are assumed to transmit through 5th-order Bessel filter. Upon demodulated by the limiter-discriminator at the receiver, the probability of bit error, which is important for performance estimation of digital system, is analyzed against SNR. The analysis based on the following parameters, that is bit rate 140kHz, frequency of pre-modulation filter f-100kHz, maximum frequency deviation of transmitter 2f=300kHz, was performed. As a result, when the telemetry system with the parameters above is designed, the probability of bit error is obtained as 10 along with fT=0.7 and h=2, T=2.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.242.2-242.2
• /
• 2014

Plasma-polymer thin films (PPTF) have been deposited on a Si(100) wafer and glass under several conditions such as different RF power by using plasma-enhanced chemical vapor deposition (PECVD) system. Ethylcyclohexane, ammonia gas, hydrogen and argon were utilized as organic precursor, doping gas, bubbler gas and carrier gases, respectively. PPTFs were grown up with RF (ratio frequency using 13.56 MHz) powers in the range of 20~60 watt. PPTFs were characterized by FT-IR (Fourier Transform Infrared), FE-SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope), Contact angle and Probe station. The result of FT-IR measurement showed that the PPTFs have high cross-link density nitrogen doping ratio was also changed with a RF power increasing. AFM and FE-SEM also showed that the PPTFs have smooth surface and thickness. Impedance analyzer was utilized for the measurements of C-V curves having different dielectric constant as RF power.

• Journal of Advanced Navigation Technology
• /
• v.28 no.2
• /
• pp.225-231
• /
• 2024

In this article, a new approach is presented to improve the unchangeable function of a ready-made millimeter-wave antenna system. By designing a metamaterial surface appropriate for the given geometry and fixed electrical characteristics of the device, the properties of the radiated fields of the RF product are changed to have directivity and higher antenna gain. Unlike other designs using periodic metamaterials for a single patch, an aperiodic metasurface is developed to handle two patches. For a higher received signal strength and a longer RF path in the 24 GHz-radio link, an aperiodic metasurface enhances the radiated fields by 10 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.964-970
• /
• 2013

This paper presents a bandpass wireless 3-D chip to chip interface technique. The proposed technique uses direct amplitude modulation of the free running oscillator which especially utilizes the coupling capacitance between two stacked chips as a part of the resonator. Therefore, the oscillator is three dimensionally configured and a simple envelope detector can be used as a receiver without any additional matching circuitry. The proposed link was designed and fabricated using 110 nm CMOS technology and experimental results successfully showed the data transmission at a data rate of 2 Gb/s for the stacked chips with a thickness of 50 ${\mu}m$ consuming 4.32 mW. The sizes of the Tx and Rx chips are 0.045 $mm^2$ and 0.029 $mm^2$, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.415-422
• /
• 2004

DSRC provides high speed radio link between Road Side Equipment and On-Board Equipment within the narrow communication area. In this paper, a 5.8 GHz down-conversion mixer for DSRC communication system was designed and fabricated using 0.8 ${\mu}{\textrm}{m}$ SiGe HBT process technology and RF/LO matching circuits, RF/LO input balun circuits, and If output balun circuit were all integrated on chip. The chip size of fabricated mixer was 1.9 mm${\times}$1.3 mm and the measured performance was 7.5 ㏈ conversion gain, －2.5 ㏈m input IP3, 46 ㏈ LO to RF isolation, 56 ㏈ LO to IF isolation, current consumption of 21 mA for 3.0 V supply voltage.