• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2004.06a
• /
• pp.101-105
• /
• 2004

본 논문에서는 온도 센서로부터 얻어지는 데이터를 전송하고 실시간으로 처리하기 위하여 RF방식을 이용한 단 방향 데이터 전송 시스템을 설계하고 그 특성을 측정하였다. 설계된 무선 전송기능의 온도 측정 시스템은 온도센서 및 제어부, 데이터 전송용 RF module로 구성되었다. 온도 측정을 위한 센서는 AD590 전류 구동 형 전압출력 센서이며 제어부는 PIC one-chip microprocessor를 사용하였다. 또한 데이터의 무선 전송을 위해 433MHz 주파수 대역의 반 이중 RF Module을 사용하여 system을 구현하였다. 실험은 10M 이내의 실내 공간 내에서 수행되었고, 임의의 온도측정 구간에 따른 온도 변화 환경에서 3가지 경우의 (3M,5M,10M) 거리 변화를 두고 데이터를 측정 및 비교 분석하였다. 실험결과 10M 이내의 거리에서는 온도센서로부터 얻어진 데이터를 실시간으로 송수신하여 결과를 처리할 수 있었으며 이를 이용한 다중 Sensor 시스템 구현이 가능한 결과를 얻었다.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.195-199
• /
• 2003

BEE 802.11 Wireless LAN protocol uses fixed transmission power. It does not consider a power control mechanism based on the distance between the transmitter and the receiver in order to improve overall channel utilization. In home environment, where stations generally lie around an AP, the AP is subject to use transmission power more than it needs. And wireless LAN stations may require different minimal desired received power. If there are many adjacent BSSs in densely populated WLAN area, they might cause RF interference to one another. In this paper we focus on the improvement of aggregate utilization by mitigating RF interference among BSSs. We show that RF interference by APs can be reduced by controlling transmission power using Link Margin information. The reduced interference will then lead to the increased aggregate throughput which is efficient resource utilization.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.1
• /
• pp.127-132
• /
• 2013

In this paper, we design the physical layer of Guardian modem for wireless public networks. The physical layer is composed of a dual-band RF (Radio Frequency) transceiver and a baseband-processor with quasi-orthogonal codes. The 2.4/5GHz dual-band RF transceiver can overcome the communication difficulty of dense 2.4GHz band for wireless public environment. Also the quasi-orthogonal code can reduce the required ASIC (Application Specific Integrated Circuit) design area. Finally, we analyze the performance of the developed system in viewpoint of data rate, BER (Bit Error Rate), PER (Packet Error Rate). Moreover we verify the performance of the dual-band RF communication.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.896-898
• /
• 2012

Recently, many countries are making efforts for the development of ocean resources because the necessity and importance of the ocean resources are increased. Underwater sensor networks have emerged as a very powerful technique for many applications, including monitoring, measurement, surveillance and control and envisioned to enable applications for oceanographic data collection, ocean sampling, environmental and pollution monitoring, offshore exploration, disaster prevention, tsunami and seaquake warning, assisted navigation, distributed tactical surveillance, and mine reconnaissance. The idea of applying sensor networks into underwater environments (i.e., forming underwater sensor networks) has received increasing interests in monitoring aquatic environments for scientific, environmental, commercial, safety, and military reasons. The data obtained by observing around the environment are wireless-transmitted by a radio set with various waves. According to the technical development of the medium set, some parameters restricted in observing the ocean have been gradually developed with the solution of power, distance, and corrosion and watertight by the seawater. The actual matters such as variety of required data, real-time observation, and data transmission, however, have not enough been improved just as various telecommunication systems on the land. In this paper, a wireless management system will be studied through a setup of wireless network available at fishery around the coast, real-time environmental observation with RF sensor, and data collection by a sensing device at the coastal areas.

• KIPS Transactions on Software and Data Engineering
• /
• v.8 no.12
• /
• pp.483-490
• /
• 2019

In the Network Intrusion Detection System (NIDS), the function of classification is very important, and detection performance depends on various features. Recently, a lot of research has been carried out on deep learning, but network intrusion detection system experience slowing down problems due to the large volume of traffic and a high dimensional features. Therefore, we do not use deep learning as a classification, but as a preprocessing process for feature extraction and propose a research method from which classifications can be made based on extracted features. A stacked AutoEncoder, which is a representative unsupervised learning of deep learning, is used to extract features and classifications using the Random Forest classification algorithm. Using the data collected in the IOT environment, the performance was more than 99% when normal and attack traffic are classified into multiclass, and the performance and detection rate were superior even when compared with other models such as AE-RF and Single-RF.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.1
• /
• pp.9-15
• /
• 2005

Most of location systems use RF signal. Because multipath is too severe at indoor environment, RF signal are usually used in outdoor positioning such as GPS. To overcome the difficulty at indoor positioning, m positioning is recently developed and is being vigorously studied. Some standardizations on UWB are in progress at IEEE 802.15 committee. In developing UWB positioning system, we should consider the synchronization of sensor network, positioning algorithm, sensor allocation, and so on. This paper presents a comparison of TDOA positioning algorithms that are widely used in location systems. Two algorithms are compared; one is derived by linearization, and the other is by analytic solution(CH algorithm). Simulation results show that the CH algorithm is superior to the linearized least square at indoor environment in that CH algorithm shows consistent positioning performance regardless of the visibility and geometry of basestations.

• Journal of Korean Society for Geospatial Information Science
• /
• v.17 no.1
• /
• pp.113-120
• /
• 2009

Through the automatic sensing of the environment, USN technology can give the best services. In this work, we have developed an active RFID system and examined its performance. By implementing it into water quality sensors, we constructed a system that can detect diverse indoor/outdoor environment and provide information about the pollution level obtained from the temperature and PH sensors. Our RF system had an internal Print-on-PCB antenna for the miniaturization of the tag. We used a RF transceiver CC2510 chipset of TI company to realize the active RFID function. By using RSSI constants obtained, we performed the evaluation of real time location accuracy with a software written in Labview. Among 10 arbitrary locations, we obtained average measurement errors of 1.69 m in x axis and 1.66 m in y axis. This technology can be applied to logistics, environmental monitoring, prevention of missing children and various applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.272.2-272.2
• /
• 2016

Copper-Tin (CuSn) thin films were synthsized by rf magnetron co-sputtering method with pure Cu and Sn metal targets with various rf powers and sputtering times. The obtained CuSn thin films were characterized by a surface profiler (alpha step), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray induced Auger electron spectroscopy (XAES), and contact angle measurement. The deposition rates were calculated by the thickness of CuSn thin films and sputtering times. We observed hexagonal Cu20Sn6 and cubic Cu39Sn11 phases from the films by XRD measurement. From the survey XPS spectra, the Cu and Sn main peaks were observed. Therefore, we could conclude CuSn thin films were successfully fabricated on the substrate in this study. The changes of oxidation states and chemical environment of the films were investigated with high resolution XPS spectra in the regions of Cu 2p, Cu LMM, and Sn 3d. Surface free energy (SFE) and wettability of the CuSn thin films were studied with distilled water (DW) and ethylene glycol (EG) using the contact angle measurement. The total SFE of CuSn thin films decreased as rf power on Cu target increased. The contribution to the total SFE of dispersive SFE was relatively superior to polar SFE.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.3
• /
• pp.208-216
• /
• 2017

This paper presents the design method of an FMCW(frequency-modulated continuous-wave) altitude simulator which generates propagation delay signals according to target distances to test the radar altimeter. To improve the conventional RF method for creating delay signals, the simulator is designed by the RF-optics-RF method using optical delay lines. In addition, it is designed to simulate the Doppler shift and jamming that may occur in actual flight environment. In order to evaluate the performance of the developed simulator, the integration tests have been conducted with the radar altimeter. Through the test, we successfully verified the performance of the simulator.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.4
• /
• pp.455-468
• /
• 2014

This paper presents seamless hand off implementation suggesting algorithm and Measuring /testing at the tunnel environment in order to derive the ideal value of wireless data transmission in RF-CBTC train control system modeled by Shinbundang Operation System. In addition, it proposes the ideal value(-57dB) for reducing the re-transmission or frequency interference rate and demonstrates frequency optimization which enables highly reliable data communication in Train control system using wireless communications. Based on these result, Shinbundang phase 2 plan to apply to this system.