• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.282-288
• /
• 2014

In this paper, we have analyzed and designed a digital RF receiver based on the optimization of the dynamic range parameter to secure the wideband characteristics and linearity of digital radar receivers. To improve the wideband characteristics and dynamic range, a low noise amplifier is matching design with a noise source to minimize the noise figure in 1 GHz bandwidth and we improved the linearity of RF-receiver by securing the conversion gain characteristics of receiver through the design of active mixer. RF receiver is designed to give gain 63 dB, noise figure 1.2 dB and dynamic range of RF receiver has 75.8 dB in a wide band of 8.8~9.8 GHz. It is shown to be applicable to X-band digital radar receiver.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.753-758
• /
• 2009

This paper is proposed the hardware structure and signal processing method of the RF-Tag based on heart sound to develop the mobile biomedical information device for the u-healthcare system. The RF-Tag in this study is consisted of a skin temperature sensor, a dynamic microphone for heart sound detection, Bluetooth communication to transmute healthcare data, and pulse period detection algorithm with adaptive gain controller. We experimented to evaluate performance of the RF-Tag in noisy environments. In addition, the RF-Tag has shown the good performance in the results of experiment. If the proposed methods in this study apply to design the u-healthcare device, we will be able to get the exact health data on real time in mobile environments.

• Journal of Korea Society of Industrial Information Systems
• /
• v.6 no.2
• /
• pp.31-37
• /
• 2001

In this paper, We designed and implemented an RF module for WLL multi-channel personal stations. Then, we experimentally evaluated in receiving sensitivity, adjacent channel interference selectivity and spurious response limit. From the measurement results on the RF module for WLL multi-channel personal stations, we observed and confirmed as follows: First, the variation in output power level was kept to be less than 30 dBm in the range of the input power level from -90 dBm to -30dBm. This measurement result confirmed the dynamic range of 60 dB. Secondly, at the output stage of the RF module, the gain flatness in the pass band was measured to be less than 2dB, which confirmed a precise control of the bandspread signals. Thirdly, at the RF module, the bandwidth and power level in transmission were measured to be 10 MHz, respectively we note that these features satisfy the design specifications.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.1 s.4
• /
• pp.21-30
• /
• 2004

This paper describes the design of RF link between RSE and OBU of ETCS and the analysis of the antenna beam pattern to get a proper communication area in the cross direction and traveling direction of lanes. This stage should be performed prior to determination of system requirements of ITS service based on active DSRC. This study is important and fundamental technical analysis to design and implement base station of ETCS.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.902-905
• /
• 2006

This paper presents a new RF testing scheme based on a design-for-testability (DFT) method for measuring functional specifications of RF integrated circuits (IC). The proposed method provides input impedance. gain, noise figure. input voltage standing wave ratio (VSWR) and output signal-to-noise ratio (SNR) of a low noise amplifier (LNA). The RF test scheme is based on theoretical expressions that produce the actual RF device specifications by output DC voltages from the DR chip.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.1
• /
• pp.86-91
• /
• 2008

An integrated multidisciplinary analysis and design system plays a critical role in the preliminary design of an aircraft. In this work a system based on the CATIA is developed for multidisciplinary computational design; aerodynamics, elasticity, and radar frequency stealth. Common data base of geometry and rectangular grids is generated and used for aerodynamic and structural analysis, while derivative triangular grids are generated for the RCS calculation. The panel method (PANAIR), FEM (NASTRAN), and PO technique are used for aerodynamic, structural, and RF stealth computations, respectively, and several additional algorithms are developed for the effective communication of the common data.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.3
• /
• pp.87-94
• /
• 2006

For realizing an ubiquitous home network(uHome-net), various sensors should be able to be connected to an integrated wire/wireless sensor network. This paper describes an application case of applying LonWorks technology being widely used in control network to wire/wireless sensor network in uHome-net and the design and application of LonRF device that consists of a neuron chip including LonTalk protocol, a 433.92MHz RF transceiver, a sensor, and application programs. As an application example of the LonRF device, the LonRF smart badge that can measure the 3D location of objects in indoor environment and interwork with the uHome-net was developed. LonRF device based home network services were realized on the uHome-net testbed such as indoor positioning service, remote surveillance service and remote metering service were realized. This research shows that LonWorks technology based sensor network could be applicable to the control network in an ubiquitous home network and the LonRF device can be used as a wireless node in various sensor networks.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.953-956
• /
• 2005

Low voltage actuation and high isolation characteristics are key features to be solved in electrostatic RF switch design. Since these parameters in the conventional parallel plate MEMS switch design are in trade-off relation, both requirements cannot be met simultaneously. In vertical comb design, however, the actuation voltage is independent to the vertical separation distance between the contact electrodes. Then, we can design the large separation distance between contact electrodes to get high isolation. We have designed an RF MEMS switch which has -40dB isolation at 5 GHz and 6 V operation voltages. The characteristics of the fabricated switch are being evaluate.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2286-2292
• /
• 2011

In this paper we present the design of Low Noise Amplifier(LNA), mixer and filter for RF front-end part of partial discharge monitoring system. The monitoring system of partial discharge in high voltage power machinery is used to prevent many kinds of industrial accidents, and is usually composed of three parts - sensor, RF front-end and digital microcontroller unit. In our study, LNA, mixer and filter are key components of the RF front-end. The LNA consists of common gate and common source-cascaded structure and uses the resistive feedback for broad band matching. A coupled line structure is utilized to implement the filter, of which size is reduced by the meander structure. The mixer is designed using dual gate structure for high isolation between RF and local oscillator signal.

• ETRI Journal
• /
• v.42 no.3
• /
• pp.333-340
• /
• 2020

We consider a hybrid combiner design for downlink massive multiple-input multiple-output systems when there is residual inter-user interference and each user is equipped with a limited number of radio frequency (RF) chains (less than the number of receive antennas). We propose a hybrid combiner that minimizes the mean-squared error (MSE) between the information symbols and the ones estimated with a constant amplitude constraint on the RF combiner. In the proposed scheme, an iterative alternating optimization method is utilized. At each iteration, one of the analog RF and digital baseband combining matrices is updated to minimize the MSE by fixing the other matrix without considering the constant amplitude constraint. Then, the other matrix is updated by changing the roles of the two matrices. Each element in the RF combining matrix is obtained from the phase component of the solution matrix of the optimization problem for the RF combining matrix. Simulation results show that the proposed scheme performs better than conventional matrix-decomposition schemes.