• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.2
• /
• pp.291-298
• /
• 2017

In this paper, we derive the achievable degrees of freedom (DoF) for multiple-input multiple-output (MIMO) Z-interference channels (Z-IC) with reconfigurable antennas at the receivers, assuming that channel state information is not available at the transmitters. We propose a new linear scheme to align interfering signals and to decode desired signals through the designed preset mode switching pattern of reconfigurable antennas at the receivers. The key idea of our scheme is to use interfering signals as a side information at the interfered receiver by being silent at the corresponding transmitter during some time slots. Consequently, it is shown that the reconfigurable antennas at the receivers can bring a DoF gain if the number of preset modes is greater than the number of RF chains at the receivers.

• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.249-257
• /
• 2003

The bio-telemetry technologies, that use the wireless miniaturized telemetry module implanted in the human body and transmits several biomedical signal from inside to outside of the body, have been expected to solve the problem such as the patient's inconvenience and the limit for diagnosis. In the case of transceiver system using the wireless RF transmission method, the method of three-dimensional localization for implantable miniaturized telemetry module is necessary to detect the exact position of disease. A new method for three-dimensional localization using small loop antenna in the implantable miniaturized telemetry module was proposed in this paper. We proposed a method that can accurately determine the position of telemetry module by analyzing the differences in the strength of signal, which is received at each of the small size RF receiver array installed on the body surface.

• 한국해양학회지
• /
• v.30 no.1
• /
• pp.27-38
• /
• 1995

For the study of oceanic surface current, this work presents a system design which is composed of three parts, a Global Positiong System(GPS) unit, a transmitter with radio frequency (RF) modem and an antenna which are housed in a plastic spherical buoy, and computerised of VHF receiving system. The key idea for this study is to employ a commercially available GPS on a drifting buoy and to utilize the receiver position information from the buoy in determining the Lagrangian motion of surface ocean waters. Great efforts has been paid to the system design which would demand several points in harsh conditions common in the sea surface, that is power supply problems housed inside of a plastic buoy, optimizing transmitting radio frequency which limits transmitting distance to a receiving station. for all these difficulties, the system appears to be promising in future oceanic applications and is considered to economical compared to ARGOS drift buoy which is being used by commercial base. We believe that the system needs to be improved in terms of several aspects such as a longer transmitting distance, a power supply and software. for the test experiments in situ, the system has employed off the coast of Ku Ryong Po int the southeast part of Korea and successfully collected the surface current data. The results are presented for two cases from 21 to 31, March 1994 and 21 to 25, June 1994 in terms of current statistics and trajectories of drifting buoys.

• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2020

In this research, we develop an airborne equipment radiating S/C-band signal to a target located at a long distance. RF interface of the equipment comprises band-specific transmitters and an broadband antenna to satisfy EIRP(effective isotropic radiated power) requirements. The equipment is in a shape of a POD like an aircraft fuel tank. The measured weight of the equipment is 119.8 kg, the CG(center of gravity) is 1391.35 mm and the MOI(moment of inertia) are 46.07 ± 0.05(I_yy) kg·㎡, 45.36 ± 0.09(I_zz) kg·㎡. All results are found to meet the requirements for aircraft installation. To verify flight safety, EMI(electromagnetic interference) tests (RE102, CE102), environmental tests (high/low temperature operation, altitude), intra-system EMC(electromagnetic compatibility) and HERP(hazards electromagnetic radiation personnel) tests have been conducted and all the test results met the requirements. It is confirmed that the equipment could be mounted on the aircraft by meeting all electrical and mechanical requirements.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8A
• /
• pp.661-668
• /
• 2012

In this paper, we introduce the low power wireless communication method and propose new protocol and algorithm for wireless communication which can be applied Active RFID system. Transceiver module is composed of MCU, RF transceiver and chip antenna. and it used the lithium coin battery for power supply. The experimental result is confirmed minimum power consumption which show average $10{\mu}A$(packet transmit) and $30{\mu}A$(packet receive) per second. It can be used ultra low power wireless communication. this result is possible for using the algorithm which predict the arrival time of packet. and it indicates that are possible to prevent malfunction and enhance responsiveness.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.4
• /
• pp.453-461
• /
• 2011

In order to use more efficiently limited frequency resources at the broadcasting band and to eliminate blanket area of the terrestrial broadcasting and to improve broadcasting quality. The importance of repeaters has increasing continuously. However, in case of T-DMB digital on channel repeater in OFDM systems, some of the signal radiated feedback again at the receiver antenna. So it generates feedback signal interference in repeater system. Also phase noise increases ICI(Inter Carrier Interference). It affects seriously the frequency domain equalizer. In this paper, we remove the feedback signal interference by LMS with correlation. Also we propose an effective equalizer algorithm that can remove ICI caused by phase noise and the power amplifier's back-off. In this simulation results, this system is satisfied the performance of BER=$10^{-4}$ at less than SNR=14 dB after compensation of phase noise.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.114-122
• /
• 2014

For an efficient finite-difference time-domain(FDTD) analysis of coaxial-probe feeding structures in radio frequency(RF) and microwave bands, an interrelation between equivalent source modeling techniques is investigated. In existing literature, equivalent source models with delta-gap or magnetic-frill concepts have been developed by many researchers. It is well known that FDTD implementation and computational accuracy of these source models are slightly different. In this paper, the interrelation between FDTD equivalent source models for coaxial feeding structures under the quasi-static approximation(QSA) is presented. As a function of FDTD equivalent source models, time-domain and frequency-domain responses of a coaxial-probe fed conical monopole antenna are calculated numerically. And comparison results of computational accuracy and efficiency are provided.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.199-207
• /
• 2011

A Ku-band low noise amplifier has been designed and fabricated by using 0.25 um SiGe BiCMOS process. The developed Ku-band LNA RFIC which has been designed with hetero-junction bipolar transistor(HBT) in the BiCMOS process have noise figure about 2.0 dB and linear gain over 19 dB in the frequency range from 9 GHz to 14 GHz. Optimization technique for p-tap value and electro-magnetic(EM) simulation technique had been used to overcome the inaccuracy in the PDK provided from the foundry service company and to supply the insufficient inductor library. The finally fabricated low noise amplifier of two fabrication runs has been implemented with the size of $0.65\;mm{\times}0.55\;mm$. The pure amplifier circuit layout with the reduced size of $0.4\;mm{\times}0.4\;mm$ without the input and output RF pads and DC bais pads has been incorporated as low noise amplication stages in the multi-function RFIC for the active phased array antenna of Ku-band satellite VSAT.

• Applied Science and Convergence Technology
• /
• v.26 no.2
• /
• pp.34-41
• /
• 2017

A 2.45 GHz microwave plasma with linear antenna has been prepared for hydrophobic and wear-resistible surface coating of carbon steel. Wear-resistible properties are required for the surface protection of cutting tools and achieved by depositing a hydrogenated amorphous carbon film on steel surface through linear microwave plasma source that has $TE_{10}-TEM$ waveguide. Compared to the existing RF plasma source driven by 13.56 MHz, linear microwave plasma source can easily generate high density plasma and provide faster deposition rate and wider process windows. In this study, $Ar/CH_4$ gas mixtures are used for hydrogenated amorphous carbon film deposition. When microwave power of 1000 W is applied, 40 cm long uniform $Ar/CH_4$ plasma could be obtained in gas pressure of 200~400 mTorr. The Vickers hardness measurement of hydrogenated amorphous carbon film on steel surface was evaluated. It was found the optimized deposition condition at $Ar:CH_4=25:25$ sccm, 300 mTorr with microwave power of 1000W and RF bias power of 100W. By deposition of hydrogenated amorphous carbon film, contact angle on steel surfaces increases from $43.9^{\circ}$ to $93.2^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.900-908
• /
• 2016

In this paper, we have studied the tracking system with a single channel monopulse receiver that has a comparative advantage of costs, size, weight, and power consumption over the general 3-channel monopulse receivers. After the single channel monopulse system was composed of an antenna, a monopulse receiver, a servo unit, a RF signal processor unit and a power supply unit, we analyzed the basic tracking performance of the tracking error angle and the pointing loss. And we proved the tracking performance to a moving target in the outdoor environment. On the Analysis of the tracking test results, the single channel monopulse system shows a equal or higher performance over the general 3-channel monopulse system and also has advantages of the system implementation. Also, it is concluded that this study is useful to apply a single channel monopulse receiver with benefits of production price and miniaturization when the monopulse tracking systems will be developed in the future.