• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.2
• /
• pp.76-80
• /
• 2008

In this study, we synthesized ATO films using RF magnetron sputtering method consisted of $SnO_2$ target added Sb of 6 wt% and investigated the effect of $O_2$ on structural, electrical, and optical properties of ATO films. As a result, in case of $O_2$/Ar ratio of 0.11, we obtained ATO films exhibit the properties such as the resistivity about $8{\times}10^{-3}[{\Omega}-cm]$, the transmittance of 85.17%, and retile structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.301-304
• /
• 2002

We investigated the structural and electrical properties of Ce-doped Ba($Zr_{0.2}Ti_{0.8}$)$O_3$(BCZT) thin films with a mole fraction of x=0.2 and a thickness about 100 nm. BCZT films were prepared on Pt/Ti/$SiO_2$/Si substrate by a RF magnetron sputtering system. We have measured the thickness profile with Ar/$O_2$ ratio and the surface roughness. It was observed that the oxygen gas, which introduced during the film deposition, have an influence on the roughness of the film and the film roughness was reduced by annealing from 2.33 nm to 2.02 m (RMS at $500^{\circ}C$, Ar:6 scrim, $O_2$:6 sccm). We have found that annealing procedure after top electrode deposit can reduce the dissipation factor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.257-257
• /
• 2011

The amorphous indium-gallium-zinc-oxide (a-IGZO) materials for use in high performance display research fields are strongly investigated due to its good performance, such as high mobility and better transparency. However, the stability of a-IGZO materials is increasingly becoming one of critical issues due to the sub-gap electron trap sites induced by rough interfaces during deposition processing. It is well-known that the threshold voltage shift is related to interface roughness and oxygen vacancy formed by breaking weak chemical bonds. Here, we report the better properties of transparent oxide transistors by reducing the threshold voltage shift with an external rf plasma supported magnetron sputtering system. Mainly, our sputtering method causes the surface of sample to be sleek, so that it prevents the formation of various defects, such as shallow electron trap sites in the interface. External rf power was applied from 0 to 50W during RF sputtering process to enhance the stability of our oxide transistor without having a large voltage shift. To observe the effects of external rf-plasma source on the properties of our devices, Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Transmission Electron Microscopy (TEM) are carried out to observe surface roughness and morphology of sputtered thin film. In addition, typical electrical properties, such as I-V characteristics are analyzed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.361-364
• /
• 2003

It was investigated that the structural and electrical Properties of Ce-doped Ba(Zr$_{x}$Ti$_{1-x}$ )O$_3$ (BCZT) thin films with a mole fraction of x=0.2 and a thickness about 100 nm. BCZT films were prepared on Pt/Ti/SiO$_2$/Si substrate by a RF magnetron sputtering system. We have measured the thickness profile with Ar/O$_2$ ratio and the surface roughness. It was observed that the oxygen gas, which introduced during the film deposition, have an influence on the roughness of the film and the film roughness was reduced by annealing from 2.33 nm to 2.02 nm (RMS at 500 $^{\circ}C$, Ar:6 sccm, $O_2$:6 sccm). It was found that annealing procedure after top electrode deposit can reduce the dissipation factor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.154-157
• /
• 2006

The counter electrode widely used in DSCs (Dye-sensitized Solar Cells) is constructed of conducting glass substrates coated with Pt films, where the platium acts as a catalyst. Pt counter electrodes in DSCs are one important component. It is expected that characteristics of Pt electrodes strongly depend on fabrication process and its surface condition. In this study, Pt counter electrode surface of DSC is deposited by reactive RF magnetron sputtering under the conditions of Ar 5mtorr, RF power of 120w and substrate temperature of $100^{\circ}C$. Surface morphology of Pt electrodes was investigated by FE-SEM and AFM. And this paper shows our recent results and technology to fabricate the new designed cell with Pt electrodes deposited by sputtering method. We have achieved fill factor 65% and photoelectric conversion efficiency around 2.6% as the best results of new designed DSCs structure.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2021

The properties of the electron transport layer (ETL) have a great effect on perovskite solar cell performance. Depositing conformal SnO2 ETL on bottom textured silicon cells is essential to increase current density in terms of the silicon-perovskite tandem solar cells. In the recent study, the SnO2 electron transport layer deposited by the sputtering method showed an efficiency of 19.8%. Also, an electron transport layer with a sputtered TiO2 electron transport layer in a 4-terminal tandem solar cell has been reported. In this study, we synthesized SnOx ETL with a various sputtering power range of 30-60W by Radio-frequency (RF)-magnetron sputtering. The properties of SnOx thin film were characterized using ellipsometer, UV-vis spectrometer, and IV measurement. With a sputtering power of 50W, the solar cell showed the highest efficiency of 13.3%, because of the highest fill factor by the conductivity of SnOx film.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.5
• /
• pp.361-366
• /
• 1999

The life of AC PDP depends largely on the sputtering-resistant property of the protecting layer such as MgO thin-film. However, it is very difficult to measure the sputtering-resistant property in the stable driving conditions of AC PDP. In this paper we have suggested a high speed measurement technique of the sputtering-resistant property of MgO thin-film by applying the MgO thin-film as the target of RF magnetron sputtering system. We have also applied this method to the e-beam MgO and sputter-MgO and e-beam MgO superior to sputter-MgO 3 times over. Also, the relation of Xe gas partial pressure(X) and sputtered thickness(Y) was Y=3.4X+13.5.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.8
• /
• pp.674-677
• /
• 2011

The dependency of sputtering power on the electrical performances in amorphous HIZO-TFT (hafnium-indium-zinc-oxide thin film transistors) has been investigated. The HIZO channel layers were prepared by using radio frequency (RF) magnetron sputtering method with different sputtering power at room temperature. TOF-SIMS (time of flight secondary ion mass spectrometry) was performed to confirm doping of hafnium atom in IZO film. The field effect mobility (${\mu}FE$) increased and threshold voltage ($V_{th}$) shifted to negative direction with increasing sputtering power. This result can be attributed to the high energy particles knocking-out oxygen atoms. As a result, oxygen vacancies generated in HIZO channel layer with increasing sputtering power resulted in negative shift in Vth and increase in on-current.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.158-158
• /
• 2011

$Cu(In_xGa_{1-x})Se_2$ (CIGS) thin film solar cell is one of the most promising solar cells in photovoltaic devices. CIGS has a direct band gap which varied from 1.0 to 1.26 eV, depending on the Ga to In ratio. Also, CIGS has been studying for an absorber in thin film solar cells due to their highest absorption coefficient which is $1{\times}10^5cm^{-1}$ and good stability for deposition process at high temperature of $450{\sim}590^{\circ}C$. Currently, the highest efficiency of CIGS thin film solar cell is approximately 20.3%, which is closely approaching to the efficiency of poly-silicon solar cell. The deposition technique is one of the most important points in preparing CIGS thin film solar cells. Among the various deposition techniques, the sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have been prepared by rf magnetron sputtering method using a single target. The optical and structural properties of CIGS films are generally dependent on deposition parameters. Therefore, we will explore the influence of deposition power on the properties of CIGS films and the films will be deposited by rf magnetron sputtering using CIGS single target on Mo coated soda lime glass at $500^{\circ}C$. The thickness of CIGS films will be measured by Tencor-P1 profiler. The optical properties will be measured by UV-visible spectroscopy. The crystal structure will be analyzed using X-ray diffraction (XRD). Finally the optimal deposition conditions for CIGS thin films will be developed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.309-312
• /
• 2007

Sputter deposition followed by surface treatment was studied using reactive RF plasma as a method for preparing titanium oxide($TiO_{2}$) films on indium tin oxide(ITO) coated glass substrate for dye-sensitized solar cells(DSSCs). Anatase structure $TiO_{2}$ films deposited by reactive RF magnetron sputtering under the conditions of $Ar/O_{2}$(5%) mixtures, RF power of 600W and substrate temperature of $400^{\circ}C$ were surface-treated by inductive coupled plasma(ICP) with $Ar/O_{2}$ mixtures at substrate temperature of $400^{\circ}C$, and thus the films were applied to the DSSCs, The $TiO_{2}$ Films made on these exhibited the BET specific surface area of 95, the pore volume of $0.3cm^{2}$ and the TEM particle size of ${\sim}25$ nm. The DSSCs made of this $TiO_{2}$ material exhibited an energy conversion efficiency of about 2.25% at $100mW/cm^{2}$ light intensity.