• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.624-628
• /
• 2000

In this paper, the phenomenon to show in CDMA handset in case of which CDMA handset do not meet Traffic Rho value of IS-98B specifications, which have minimum requirements of CDMA handset about electrical performance is analyzed. This paper proposed method to improve Traffic Rho through improving the matching circuit of TX IF SAW FILTER and deleting noise of LDO(Low Dropout Regulator) to generate 3.OV_TX in TX block. HP8924C(CDMA Mobile Station Tester Set) and HP8595E(Spectrum Analyzer) measures the improved CDMA waveform.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11A
• /
• pp.933-940
• /
• 2011

In this paper, Ka-band transceiver for road watch radar system is designed and fabricated. The transceiver for road watch radar system is composed of waveform generator, frequency generator. IF transceiver and RF up/down converter. The transceiver especially has 3 different waveform mode for target detection range. The transceiver had over 150 MHz bandwidth in Ka-band and 22 dBm output power. The receiver gain and noise figure was 30 dB and 4 dB respectively. The receive dynamic range was 65.28dB and amplitude imbalance and phase imbalance of I/Q channel was 0.3 dB and 1.8 degree respectively. The transceiver meets the required electrical performances through the individual tests.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.840-845
• /
• 2013

In this paper, the broadband frequency double down-converter based on LC filter technologies has been designed and implemented, and its performances are introduced. The Designed frequency double down-converter is consisted with a low-noise amplifier, mixer, IF amplifier, LC filter, DC-block capacitor and RF-bypass capacitor. Especially, instead of active devices of a typical converter, the suggested converter designed using passive devices to provide both low-power consumption and low-cost model. As results of the measurement, the implemented frequency double down-converter realizes the broadband performance with the bandwidth of 100MHz (13~113MHz) at the center frequency of 63MHz, and its gain is approximately 40dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.174-180
• /
• 2008

The pulsed amplifier which switches the main supply voltage of RF amplifier according to input pulse signal has good efficiency and low noise level between pulses. And it has simple structure because it doesn't need a pulse modulator at input port. The pulsed amplifier using the conventional switching circuit has slow fall time compared to rise time. We proposed the novel switching circuit for improving the fall time of pulsed amplifier The proposed switching circuit is implemented by replacing FET of conventional circuit with BJT. As a result of appling this circuit to RF pulsed amplifier, the rise and fall time are 5.7 ns and 21.9 ns at 27 dBm output power, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.879-885
• /
• 2014

In this paper, we designed and fabricated wideband 3-axis isotropic antenna for the Electro-Magnetic Fields(EMFs) measurement. Each part of proposed 3-axis antenna has isotropic characteristics and arbitrary axis of proposed 3-axis antenna could be selectable using RF switch. Also, a resistor was inserted in each axis of proposed 3-axis antenna for improving antenna gain and noise suppression characteristics, and port impedance of each dipole antenna were matched by balun. For the performance verification of antenna, GTEM Cell which generates standard electromagnetic field was used for the derivation of antenna factor and receiver sensitivity. As a result, fabricated 3-axis isotropic antenna has receiver sensitivity of 0.12~4.2 mV/m and typical VSWR of 3.3:1 within a wide operation frequency range from 0.03 MHz to 3 GHz.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.649-654
• /
• 2012

This paper presents a novel 16-quadrature-amplitude-modulation (QAM) E-band communication system. The system can deliver 10 Gbps through eight channels with a bandwidth of 5 GHz (71-76 GHz/81-86 GHz). Each channel occupies 390 MHz and delivers 1.25 Gbps using a 16-QAM. Thus, this system can achieve a bandwidth efficiency of 3.2 bit/s/Hz. To implement the system, a driver amplifier and an RF up-/down-conversion mixer are implemented using a $0.1{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor (GaAs pHEMT) process. A single-IF architecture is chosen for the RF receiver. In the digital modem, 24 square root raised cosine filters and four (255, 239) Reed-Solomon forward error correction codecs are used in parallel. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 21.5 dB.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.4
• /
• pp.295-301
• /
• 2008

Recently, the demand on mm-wave (millimeter-wave) applications has increased dramatically. While circuits operating in the mm-wave frequency band have been traditionally implemented in III-V or SiGe technologies, recent advances in Si MOSFET operation speed enabled mm-wave circuits realized in a Si CMOS technology. In this work, a 58 GHz CMOS LC cross-coupled VCO (Voltage Controlled Oscillator) was fabricated in a $0.13-{\mu}m$ Si RF CMOS technology. In the course of the circuit design, active device models were modified for improved accuracy in the mm-wave range and EM (electromagnetic) simulation was heavily employed for passive device performance predicttion and interconnection parasitic extraction. The measured operating frequency ranged from 56.5 to 58.5 GHz with a tuning voltage swept from 0 to 2.3 V. The minimum phase noise of -96 dBc/Hz at 5 MHz offset was achieved. The output power varied around -20 dBm over the measured tuning range. The circuit drew current (including buffer current) of 10 mA from 1.5 V supply voltage. The FOM (Figure-Of-Merit) was estimated to be -165.5 dBc/Hz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.321-326
• /
• 2018

This study describes the design and implementation of TRM(Transmit and Receiver Module) for detection for targets of small RCS(Radar Cross Section). Through the pre-simulation analysis of radar system about RF, the main specifications of TRM are verified. After the fabrication of TRM, the main characteristics such as the maximum output, noise figure, spurious were confirmed. In the future, the radar system test will be carried out by assembling TRMs, antenna radiator, and the transceiver that generates and receivers the radar waveform reflected.

• Journal of Communications and Networks
• /
• v.13 no.6
• /
• pp.655-663
• /
• 2011

Diffuse optical wireless (DOW) systems have the advantage that they do not require point-to-point siting so one transmitter can communicate with several receivers. In this paper, we investigate multiple access scheduling methods for downlink orthogonal frequency division multiplexing (OFDM) in diffuse optical wireless networks. Unlike the radio frequency (RF) channel, the DOW channel has low-pass filter characteristics and so requires different scheduling methods than those developed for the RF channel. Multi-user diversity orthogonal frequency division multiple access (OFDMA) systems nominate a cluster of subcarriers with the largest signal-to-noise-ratio for transmission. However, in a DOW channel, most users would choose the lowest frequency clusters of subcarriers. To remedy this problem, we make two proposals. The first is to use a variable cluster size across the subcarriers; the lower frequency clusters will have fewer subcarriers while the higher frequency clusters will have more subcarriers. This will equalize the capacity of the clusters. The second proposal is to randomize a user's cluster selection from a group of clusters satisfying a minimum threshold. Through simulation it is shown that combining these strategies can increase the throughput while ensuring a fair distribution of the available spectrum.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.889-899
• /
• 1999

A technique to obtain an exact frequency characteristics of desired targets in radar measurements is presented. The pulsing network composed of two RF switches was installed between the Network Analyzer and the antenna, and the backscattering from a metal sphere was measured at X-band. It is shown that the pulsing effectively eliminated undesired returns from antenna and other circuitry of the systems. The antenna return was suppressed by more than 60 dB, and the signal-to-noise ratio was improved drastically. The pulsed frequency data were processed to extract the responses of the desired target. The result agrees well with the theoretical backscattering characteristics of the sphere. The methods presented here are applicable to RCS measurements in compact ranges, and also to the backscattering measurements of distributed targets outdoors.