• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.51-54
• /
• 2000

In this paper, $Ba_{0.5}$Sr$_{0.5}$TiO$_3$ thin films were prepared on Pt/Ti/SiO$_2$/Si substrate by RF magnetron sputtering method. We investigated effect of deposition conditions (especially RF input power) on structural properties of BST thin films. Deposit conditions of BST films were set working gas ratio, Ar:O$_2$= 70 : 30, working pressure 10mTorr, and RF input power 25W, 50W, 75W and 100W. Post-annealing using rapid thermal annealing(RTA) performed at 45$0^{\circ}C$, 55$0^{\circ}C$, $650^{\circ}C$, and 75$0^{\circ}C$ in oxigen ambient for 60 sec, respectively. The structural properties of BST films on Pt/Ti/SiO$_2$/Si substrate analysed by X-ray diffraction(XRD).).).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.169-170
• /
• 2007

In this paper we report upon an investigation into the effect of sputter pressure and RF power on the electrical properties of Gallium doped zinc oxide (GZO) film. GZO films were deposited on glass substrate without substrate temperature by RF magnetron sputtering from a ZnO target mixed with 5 wt% $Ga_2O_3$. Argon gas pressure and RF power were in the range of 1~11 mTorr, and 50~100 W, respectively. However, the resistivity of the film was strongly influenced by the sputter pressure and RF power. We were able to achieve as low as $1.5{\times}10^{-3}\;{\Omega}cm$, without substrate temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.939-942
• /
• 2004

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors were Prepared by using the capacitively coupled RF magnetron sputtering method. In this paper the effect of RF discharge power on the electrical, optical and structural properties were investigated experimentally. The results show that the structural and electrical properties of the film are highly affected by the variation of RF discharge power. The optimum growth conditions were obtained for films doped with 2 wt% of $Al_2O_3$ and 200 W in RF discharge power, which exhibit a resistivity of $10.4{\times}10^{-4}{\Omega}-cm$ associated with a transmittance of 89.66 % for 1000nm in films thickness in the wavelength range of the visible spectrum.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.104-104
• /
• 2003

RF magnetron sputtering 법을 이용하여 LaA1O$_3$, SrTiO$_3$, MgO 단결정 기판 위에 BaTiO$_3$ 박막을 에피텍셜하게 증착하여 박막의 특성과 마이크로 웨이브에서의 유전특성을 평가하였다. 각 기판위에 증착한 박막의 격자상수와 FWHM을 조사하였고, pole figure로 에피텍셜 성장을 관찰하였다. 각 시편에 상부 전극으로 interdigital 타입의 전극을 photolithography 하여 캐패시턴스와 tan $\delta$을 조사하였다. 각 기판의 변화에 따른 격자상수 변화와 유전 특성의 변화를 고찰하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.897-900
• /
• 2000

Annealing dependencies of the fatigue properties of SrBi$_2$Ta$_2$$O_{9}$ thin films were observed as function of substrate temperature(400-50$0^{\circ}C$) by the rf magnetron sputtering method. With increasing annealing temperature from $600^{\circ}C$ to 85$0^{\circ}C$, flourite phase was crystalized to $650^{\circ}C$ and Bi-layered perovskite phase was crystalized above $700^{\circ}C$. The fatigue characteristics of SBT thin films deposited on Pt/TiO$_2$/SiO$_2$/Si substrate did not change up to 101o switching cycles.s.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.192-192
• /
• 2009

AZO films were prepared by $Ar:H_2$ gas RF magnetron sputtering system with a AZO (2wt% $Al_2O_3$) ceramic target at a low temperature of $100^{\circ}C$. To investigate the influence of $H_2$ flow ratio on the properties of AZO films, $H_2$ flow ratio was changed from 0.5% to 2%. As a result, the AZO films deposited with 1% $H_2$ addition showed electrical properties with a resistivity of $5.06{\times}10^{-3}{\Omega}cm$. The spectrophotometer-measurements showed the transmittance of 86.5% was obtained by the film deposited with $H_2$ flow ratio of 1% in the range of 940nm for GaAs/GaAlAs LED.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.123-123
• /
• 2009

In our experiment, a PTFE was sputter-coated on substrates to induce water-repellent properties and the RF-magnetron sputtering method for fabrication of PTFE film is used due to the advantages of the simple process, time saving, environmentally friendly, insulating property, and a good adhesion property to substrates. As a result of the correlation between surface roughness of PTFE films and contact angle with water, we found that the roughness surfaces are proportioned to contact angles related to low interfacial energy.

• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.886-892
• /
• 1994

Structural and electrical properties of BaTiO3 thin films deposited on Pt/SiO2/Si substrates by RF magnetron sputtering method have been investigated. Crystallization behavior and electrical properties were studied for the films deposited under various sputtering gas compositions (Ar+O2 gas mixture) and substrate temperatures. All the films deposited above 50$0^{\circ}C$ were all crystallized and their preferred orientation changed from (001) to (111) with the addition of oxygen gas. The dielectric constant of films deposited in pure argon was about 110 and showed little dependence on the substrate temperature. But that was increased as the ratio of O2/Ar increased and its substrate temperature dependence was discernible. The highest dielectric constant reached to 550. In addition, the films deposited in mixed gas showed stable dielectric properties against the frequency and temperature.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.307-311
• /
• 2017

ZnO:Al thin films were deposited on glass substrate by RF magnetron sputtering followed by in situ heat treatment in the same chamber. Effects of in situ heat treatment on properties of ZnO:Al thin films were investigated in this study. As heat treatment temperature was increased, crystal quality was improved first and then it was deteriorated, surface roughness was decreased, and sheet resistance was also decreased. The decrease in sheet resistance was caused by increasing carrier concentration due to decreased surface roughness. The decrease in surface roughness resulted in increase of transmittance. Therefore, in situ heat treatment is an effective method for obtaining films with better electrical characteristics.

• 한국세라믹학회지
• /
• 제31권2호
• /
• pp.227-233
• /
• 1994

The Bi-Sr-Ca-Cu-O thin films were deposited by RF-magnetron sputtering method on Si(P-111) wafer without a buffer layer and annealed at various temperatures in oxygen atmosphere. The temperature dependence of electrical resistance, the microstructure of intermediate phase, and the surface morphology of films were examined by four probe method, XRD, and SEM, respectively. The chemical composition and the depth profile of the films were determined by ESCA spectra. Thin films annealed at $600^{\circ}C$ and $700^{\circ}C$ in oxygen atmosphere showed onset temperatures of 90 K and 85K, and Tc(zero) of 22K and 31K, respectively. The sample annealed at $700^{\circ}C$ had the highest volume fraction of superconducting phase and showed smooth microsturcture. In ESCA spectra, the thin films were homogeneous with depth.