• The Journal of the Korea institute of electronic communication sciences
• /
• v.2 no.1
• /
• pp.1-9
• /
• 2007

In this paper, a third-order harmonic mixer is designed using frequency multiplier theory for the Ka-band. The gate bias voltage is selected by frequency multiplier theory to maximize the third-order harmonic element ofthe fundamental LO frequency in the proposed mixer. The designed mixer has a gate mixer structure composed of a gate terminal input for the fundamental local signal ($f_{LO}$), RF signal (${RF}$) and a drain terminal output for the harmonic frequency ($3f_{LO}-f_{RF}$) respectively. The Ka-band harmonic mixer is designed and fabricated using a commercial GaAs MESFET device with a plastic package. The proposed mixer will provide a solution for the problems found in the high cost, complex circuitry in a conventional Ka-band mixer. The 33.5 GHz harmonic mixer has a -10 dB conversion gain by pumping 11.5 GHz LO with a +5 dBm level.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.27-30
• /
• 2007

This paper deals with an equivalent circuit model for RF passive components. Rational functions are obtained from the frequency responses of EM simulation by using Foster canonical partial fraction expressions. The Vector Fitting(VF) and the Adaptive Frequency Sampling(AFS) scheme are also implemented to obtain the rational functions. A passivity enforcement algorithm is applied to ensure the stability of the equivalent circuit model. In order to verify the schemes, S parameters of the equivalent circuit model is compared to those of EM simulation in case of the microstrip line structure with 3 slots in ground.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.281-284
• /
• 2009

In this paper, we propose a method that applies Adaptive Frequency Sampling(AFS) technique to the equivalent circuit model for RF passive components. Thes days wireless communication system is getting smaller and smaller. So EMI/EMC is an issue in RF. We can solve PI(Power Integrity)/SI(Signal Integrity) that one of EMI/EMC problem apply IFFT for 3D EM simulation multiple with input signal. That is time comuming task. Therefore equivalent circuit model using RF passive component is important. AFS schemes are implemented to obtain the rational functions. S parameters of the equivalent circuit moldel is compared to those of EM simulation in case of the microstrip line structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.8
• /
• pp.674-682
• /
• 2014

Radio Frequency Test Set (RFTS) is essential to verify Telemetry, Command & Ranging (TC&R) RF subsystem of both Low Earth Orbit (LEO) and Geostationary Earth Orbit (GEO) satellite during Assembly Integration & Test (AI&T). The existing RFTS was specialized for each project and needed to be modified for each new satellite. The new design enables RFTS to be used in various projects. The hardware and software was designed considering this and therefore it could be directly used in other projects within a similar test period without modification or inconvenience. It will be also easily controlled, modified, and managed through the extension in modularization according to each function and the use of COTS (commercial on-the-self) and this will improve system reliability. A more reliable RF test measurement is also provided in this new RFTS by using an accurate reference clock signal.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.270-275
• /
• 2012

This paper describes design of a variable-N frequency synthesizer for RF PLL with $0.13{\mu}m$ silicon CMOS technology being used as an application of the UWB system like MBOA. To get good performance of speed and noise super dynamic circuits was used, and to get variable-N division ratio MOSFET switching circuits was used. Especially to solve narrow bandwidth problem of the dynamic circuits load resistance value of unit divider block was varied. Simulation results of the designed circuit shows very fast and wide operation characteristics as 5~26GHz frequency range.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.1
• /
• pp.56-61
• /
• 2011

This paper describes design of a programmable frequency synthesizer for RF PLL with $0.18{\mu}m$ silicon CMOS technology being used as an application of the UWB system like MBOA. To get good performance of speed and noise super dynamic circuits was used, and to get programmable division ratio switching circuits was used. Especially to solve narrow bandwidth problem of the dynamic circuits load resistance value of unit divider block was varied. Simulation results of the designed circuit shows very fast and wide operation characteristics as 1~14GHz frequency range.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.123-127
• /
• 2017

This paper fabricated and analyzed the image rejection mixer that uses FET's channel resistance. It can be applied for capacity 64QAM that has 50MHz~90MHz of IF band, 8.17GHz of LO frequency and 8.08~8.12GHz of RF band. When IF input power is -20dBm and LO input power is 10dBm, RF output power is obtained -33.2dBm. In this case, conversion loss is 12.9dB, the suppression of 14.3dB for LO frequency and 10.4dB for image frequency. The result of two tone test shows great IMD characteristics with 51.7dBc.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1805-1812
• /
• 2011

Bandpass sampling technique has an advantage that it uses lower sampling frequency than Nyquist criterion. But special care is required in choosing sampling frequency to avoid self-image overlapping in the first Nyquist region. Recently, the second-order BPS techniques which can suppress possible self-image by using an additional ADC and by employing digital signal processing have been proposed. This paper addresses a complex BPS based SDR front-end. Unlike general second-order BPS, it needs simple FIR filter to compensate delay in the second ADC. We show a method to find proper sampling frequencies to down convert RF signals selected by tunable RF filter operating in arbitrary frequency range.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1077-1086
• /
• 2015

This paper presents a general-purpose design scheme of a filter bank (FB)-based radio frequency (RF) transceiver that operates across the entire ultra-high frequency (UHF) TV band from 470 MHz to 698 MHz and complies with the TV white space (TVWS) regulatory requirements. To this end, an intermediate frequency (IF) band-pass filter (BPF) with a sharp skirt characteristic is considered as a solution for handling the incoming signals from a baseband modem. Specifically, an FB-based BPF structure with four ceramic resonator filters that effectively rejects unwanted signals is proposed to extract a desired signal in the TV band. Achievable data rates of a cognitive radio system (CRS) employing the proposed FB-based RF transceiver at the application layer are investigated in both wired and wireless environments. The service coverage of the CRS network is measured according to several modulation and coding schemes (MCSs) of the CRS. The results show that the coverage of a wireless network in a nearly open area can be extended by more than 9.3 km in the TVWS. Experimental results also confirm that the proposed FB-based RF transceiver is adequate for utilization in TVWS applications.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.18-23
• /
• 2022

This paper examines the electromagnetic shielding structure of ultra-high frequency (UHF) RF modules used in aircraft. Advances in electrical and electronic technologies have increased the need for electronic equipment in aircraft. High-frequency wireless devices have become integrated circuits in the form of UHF integrated circuits to support a wide range of frequencies and miniaturisation. To ensure the functionality and performance of these integrated devices in aviation, shielding is necessary to prevent unexpected electromagnetic interference, which could be detrimental to aircraft safety. A shield structure was designed to protect the RF chipset from malfunctioning, and the shielding effectiveness was improved through the application of various geometric shapes.