• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.133-133
• /
• 2011

최근 나노입자를 이용한 비휘발성 메모리 소자의 제작에 대한 연구가 진행되고 있다. 특히, 실리사이드 계열의 나노입자를 적용한 소자는 일함수가 크지만 실리콘 내의확산 문제를 가지고 있는 금속 나노입자와 달리 현 실리콘 기반의 반도체 공정 적용이 용이한 잇 점을 가지고 있다. 따라서 본 연구에서는 실리사이드 계열의 화합물 중에서 4.63 eV인 Vanadium Silicide ($V_3$Si) 박막을 열처리 과정을 통하여 수 nm 크기의 나노입자로 제작하였다. 소자의 제작은 p-Si기판에 5 nm 두께의 $SiO_2$ 터널층을 dry oxidation 방법으로 성장시킨 후 $V_3$Si 금속박막을 RF magnetron sputtering system을 이용하여 3~5 nm 두께로 tunnel barrier위에 증착시켰다. Rapid thermal annealing법으로 질소 분위기에서 $1000^{\circ}C$의 온도로 30초 동안 열처리하여 $V_3$Si 나노 입자를 형성 하였으며. 20 nm 두께의 $SiO_2$ 컨트롤 산화막층을 ultra-high vacuum magnetron sputtering을 이용하여 증착하였다. 마지막으로 thermal evaporation system을 통하여 Al 전극을 직경 200, 두께 200nm로 증착하였다. 제작된 구조는 metal-oxide-semiconductor구조를 가지는 나노 부유 게이트 커패시터 이며, 제작된 시편은 transmission electron microscopy을 이용하여 $V_3$Si 나노입자의 크기와 균일성을 확인했다. 소자의 전기적인 측정은 E4980A capacitor parameter analyzer와 Agilent 81104A apulse pattern generator system을 이용한 전기용량-전압 측정을 통해 전하저장 효과를 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.475-475
• /
• 2013

Cuprous oxide ($Cu_2O$)는 밴드갭이 2.17 eV p-type 산화물 반도체로써 태양에너지 변환기, photocatalysis (광촉매작용), 센서, 스위칭 메모리 등 응용이 다양한 재료이다. 산화물 반도체의 기본 특성은 나노/마이크로 범위 안에서 재료의 표면형태, 크기, 구조와 형상 공간방향등에 크게 영향을 받는다. 그렇기 때문에 원하는 $Cu_2O$ 특성을 얻기 위해서 성장 거동을 아는 것은 매우 중요하다. RF 마그네트론 스퍼터법으로 rod 성장 사례는 잘 알려지지 않았다. 그래서 RF 마그네트론 스퍼터법 $Cu_2O$ rod 형성 실험을 통하여 $Cu_2O$ 형성과 성장 거동을 알아보았다. RF 마그네트론 스퍼터법으로 $Cu_2O$ rod를 glass 기판 위에 Cu metal target을 이용하여 형성시켰다. $Cu_2O$ rod 합성을 위해 기판온도 및 산소분압 O2/(Ar+O2)=3%, 5%, 7% 증착시간 등을 변화시켜 실험하였다. 성장된 rod의 분석은 XRD, SEM으로 확인하였다. 성장 거동은 증착온도와 증착시간에 차이를 보였다. 증착온도 $550^{\circ}C$에서 rod가 생성되는 것을 관찰하였다. 증착시간이 길어질수록 rod 길이가 길어지고 일정 시간이 지나면 rod의 길이 성장보다는 두께(폭)가 성장하는 것을 확인하였다. 증착온도 $550^{\circ}C$ 그리고 산소분압 3%, 5%, 7% 조건에서 rod 합성 실험을 하였을 때 3%, 5% 조건에서 rod의 성장을 확인하였다. 이때 3%, 5% 산소분압에 따라 rod의 모양이 변화하였다. 하지만 7% 조건에서는 rod가 성장하지 않았다. 이유는 3%, 5%에서는 Cu metal peak을 확인하였지만, 7% 조건에서는 Cu metal peak이 없었다. 이로부터 Cu metal이 $Cu_2O$ rod 생성에 영향을 미치는 중요한 요소임을 예상할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.158-158
• /
• 2011

$Cu(In_xGa_{1-x})Se_2$ (CIGS) thin film solar cell is one of the most promising solar cells in photovoltaic devices. CIGS has a direct band gap which varied from 1.0 to 1.26 eV, depending on the Ga to In ratio. Also, CIGS has been studying for an absorber in thin film solar cells due to their highest absorption coefficient which is $1{\times}10^5cm^{-1}$ and good stability for deposition process at high temperature of $450{\sim}590^{\circ}C$. Currently, the highest efficiency of CIGS thin film solar cell is approximately 20.3%, which is closely approaching to the efficiency of poly-silicon solar cell. The deposition technique is one of the most important points in preparing CIGS thin film solar cells. Among the various deposition techniques, the sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have been prepared by rf magnetron sputtering method using a single target. The optical and structural properties of CIGS films are generally dependent on deposition parameters. Therefore, we will explore the influence of deposition power on the properties of CIGS films and the films will be deposited by rf magnetron sputtering using CIGS single target on Mo coated soda lime glass at $500^{\circ}C$. The thickness of CIGS films will be measured by Tencor-P1 profiler. The optical properties will be measured by UV-visible spectroscopy. The crystal structure will be analyzed using X-ray diffraction (XRD). Finally the optimal deposition conditions for CIGS thin films will be developed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.817-820
• /
• 2004

The $Sr_{0.7}Bi_{2.6}Ta_2O_9$(SBT) thin films are deposited on Pt-coated electrode($Pt/TiO_2/SiO_2/Si$) using a RF magnetron sputtering method. The ferroelectric properties of SBT capacitors with annealing time were studied. In the SEM images, Bi-layered perovskite phase was crystallized at 10min and grains largely grew with annealing tune. SBT thin films are transformed from initial amorphous phase to the fully formed layer-structured perovskite. During the annealing process at $750^{\circ}C$, we found that an fluorite-like stage is formed after 3min. In the XRD pattern, the SBT thin films after 3min annealing time had (105) orientation. The ferroelectric properties of SBT capacitor with annealing time represent a favorable properties at 60 min. The maximum remanent polarization and the coercive electric field with 60 min are $12.40C/cm^2$ and 30kV/cm, respectively. The leakage current density with 60min is $6.81{\times}10^{-10}A/cm^2$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.297-303
• /
• 2003

Mn-Ni-Co type thin films were prepared at various conditions by a rf magnetron sputtering system. At the condition. or substrate temperature of $300^{\circ}C$ and $Ar/O_2$= 10/0, a cubic spinel phase was obtained. When oxygen was included in process gas, a cubic spinel phase was not formed even after the thermal annealing at $900^{\circ}C$. The thermistor thin film had no other elements except Mn, Ni and Co. The infrared reflection spectra of the thermistor thin films showed that the films had somewhat high reflectance for incoming infrared ray with some angle. The etch rate of the thermistor thin films was about 63nm/min at a condition of DI water : $HNO_3$: HCl = 60 : 30 : 10 vol%. The B constant and temperature coefficient of resistance of the thermistor thin films were 3500 K and -3.95 %/K, respectively. The voltage responsivity of the thermistor thin film infrared sensor was 108.5 V/W and its noise equivalent power and specific detectivity were $5.1\times 10^{-7}$ W/$Hz^{-1/2}$ and $0.2\times 10^6$cm $Hz^{1/2}$/W, respectively.

• Korean Journal of Pharmacognosy
• /
• v.49 no.3
• /
• pp.270-277
• /
• 2018

Pyungwi-san has been used to treat the digestive system diseases, physconia, nausea, anorexia, and dyspepsia in Korea. In this study, an ultra-performance liquid chromatography-electrospray ionization-mass spectrometry (UPLC-ESI-MS/MS) method was optimized for simultaneous determination of the 14 marker components, spinosin, liquiritirn apioside, liquiritin, narirutin, 6'''-feruloylspinosin, hesperidin, liquiritigenin, glycyrrhizin, 6-gingerol, atractylenolide III, honokiol, atractylenolide II, magnolol, and atractylenolide I in Pyungwi-san extract. All analytes were separated on a Waters Acquity UPLC BEH $C_{18}$ analytical column ($2.1{\times}100mm$, $1.7{\mu}m$) with maintained at $45^{\circ}C$. The mobile phase consisted of 0.1% (v/v) aqueous formic acid and acetonitrile. The MS conditions were as follows: capillary voltage 3.3 kV, extractor voltage 3.0 V, RF lens voltage 0.3 V, source temperature $120^{\circ}C$, desolvation temperature $300^{\circ}C$, desolvation gas 600 L/h, cone gas 50 L/h and collision gas 0.14 mL/min. The coefficient of determination of 14 analytes was 0.9989-1.0000. The limits of detection and quantification values of the all analytes were 0.04-2.56 and 0.13-7.69 ng/mL, respectively. As a result of the analysis using the established LC-ESI-MS/MS method, the 5 components, spinosin, 6'''-feruloylspinosin, atractylenolide III, II, and I derived from Zizyphi Fructus and Atractylodis Rhizoma, were not detected in this extract. On the other hand, the 9 components except for the 5 components were 4.15-498.87 mg/kg in lyophilized Pyungwi-san extract. Among these components, glycyrrhizin, marker compound of Glycyrrhizae Radix et Rhizoma, was detected the most amount as a 498.87 mg/kg.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.105-105
• /
• 1999

차세대 기억소자에서는 집접도의 증가, 고속화, 그리고 미세화에 따라 배선간으 최소선폭이 작아지고, 새로운 다층 배선기술이 요구되는 가운데 층간절연막의 재료와 형성기술은 소자의 특성을 향상시켜주는 중요한 요소로서 열적안정성, 저유전율, 평탄화특성 등에 핵심을 두고 연구되고 있다. 본 연구에서는 5인치 p-Si(100) 위에 FTES와 O2를 precursor로 하고 carrier gas를 Ar gas하여 ICP CVD 방법으로 저유전율의 Fluorocarbonated-SiO2 박막을 형성하였다. 0.1-1kW, 13.56MHz인 rf power를 사용하였으며, 증착은 RT에서 5~10분으로 하였다. 형성된 박막은 FTIR(fourier transform infrared), XPS(x-ray photoelectron spectroscopy), 그리고 ellipsopsometer 등을 이용하여 결합모드와 F농도, 균일도 등을 측정하고, I-V와 C-V 측정장치, 그리고 SERM(scanning electrion microscopy) 등을 이용하여 유전상수, 누설전류, dielectric breakdown voltage, 그리고 박막의 stepcoverage를 측정하였다. 제작된 박막의 신뢰성은 열처리에 따른 전기적 특성으로부터 조사하였다. 형성된 fluorocarbonated 박막 결합모드는 Si-F, Si-O, O-C, C-C와 C-F였고 O2:FTES:Ar 유량을 1sccm:10sccm:6sccm으로 하여 증착한 시료에서 유전율은 2.8이었으며, 누설전류밀도는 8$\times$10-9A/cm2, Breakdown voltage는 10MV/cm 이상, 그리고 stepcoverage는 91%로 측정되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.574-577
• /
• 2001

GaN thin films on sapphire were grown by rf magnetron sputtering with ZnO buffer layer. The dependence of GaN film quality on ZnO buffer layer was investigated by X-ray diffraction(XRD). The improved film quality has been obtained by using thin ZnO buffer layer. Using Auger electron spectroscopy(AES), it was observed that the annealing process improved the GaN film quality. The surface roughness according to the annealing temperatures(700, 900, 1100$^{\circ}C$) were investigated by AFM(atomic force microscopy) and it was confirmed that the crystallization was improved by increasing the annealing temperature. Photoluminescence at 8K shows a near-band-edge peak at 3.2eV with no deep level emission.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.85-92
• /
• 2001

Thin films of ZnO and Al doped ZnO were prepared by rf magnetron sputter techniques. When the oxygen fraction in Ar-O$_2$ sputter gas was about 2.0%, the films exhibited the composition of Zn:O=1.05:1. The films prepared at 250 W contain larger grains than the films grown at 100 W. However, high deposition rate seems to deteriorates the crystallinity as well as Al-substitution, resulting in lower concentration of mobile electrons. The Al-doped ZnO films which were deposited at $500^{\circ}C$ show resistance of 1$\times$10$^-2$ Wcm; optical band gap of the films ranges from 3.25 to 3.40 eV. These electrical and optical features are related with microstructural as well as crystalline characteristics of the films.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.20-24
• /
• 1998

Thin films of diamond-like carbon(DLC) can be successfully deposited by using a magnetron plasma chemical vapor deposition (CVD) method with an rf(13.56 MHz) plasma of $C_dH_8$. Plasma characteristics are analyzed as a function of the magnetic field. As the magnetic field increases, both electron temperature ($T_e$) and density ($n_e$)increase, but the negative dc self-bias voltage (-$V_{ab}$) decreases, irrespective of gas pressures in the range of 1~7 mTorr. High deposition rates have been obtained even at low gas pressures, which may be attributed to the increased mean free path of electrons in the magentron plasma. Effects of rf power and additive gas on the structural properties of DLC films aer also examined by using various technique namely, TED(transmissio electron diffraction) microanalysis, FTIR, and Raman spectroscopies.