• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.218-227
• /
• 1998

Present study is undertaken to optimize the lubrication reliability and frictional loss of the dynamically-loaded journal bearing in hermetic reciprocating compressor with alternative refrigerant R600a application. Thermodynamic and dynamic analysis has been conducted to investigate cylinder pressure variations by substitution alternative refrigerant R600a for R12. The modeling of the dynamics of the compressor mechanism has been performed with lumped mass method. A mathematical model is developed for analyzing the dynamics of the journal bearing system with the mobility method. It takes into account the effects of the refrigerant species, aspect ratio, clearance ratio and surface roughness. A corresponding computer program is described which enables to obtain the minimum film thickness and frictional loss. Design optimization is graphically performed by parametric studies of the aspect ratio and clearance ratio.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.264-267
• /
• 1993

A high plasma density of $10^{12}cm^{-3}$ can be produced at the pressure of few mTorr with R. F input power of 300-400W. A radially uniform plasma to a radius of 7cm at the substrate was produced at the pressure of 1 mTorr. The electron density and temperature were confirmed with double Langmuir probe, $\mu$-wave interferometer. It has bee found that the dispersion relation N/B=constant not be applied at the low R.F input power(<600W) but can be applied at high R.F input power(>600W).

• Fisheries and Aquatic Sciences
• /
• v.13 no.2
• /
• pp.150-156
• /
• 2010

The separation performance of a low-pressure hydrocyclone (LPH) was evaluated for suspended-solids removal in a recirculating aquaculture system (RAS). The dimensions of the LPH were 335 mm cylinder diameter, 575 mm cylinder height, 60 mm overflow diameter, 50 mm underflow diameter, and $68^{\circ}$ cone angle. The inflow rate varied (400, 600, 800, and 1,000 mL $s^{-1}$) with 25%, 25%, 20%, and 10% of bypass ($R_f$), respectively. The maximum total separation efficiency (Et) and reduced separation efficiency (E't) for suspended solids from the effluent of the second settlement tank (before biofiltration) were 58.9% and 45.2%, respectively, at an inflow rate of 600 mL $s^{-1}$ and 25% of $R_f$. The maximum Et and E't for suspended solids from the water supply channel (after biofiltration) were 24.4% and 16%, respectively, at an inflow rate of 1,000 mL $s^{-1}$ and 10% of $R_f$. The maximum grade efficiency (Ei) was 51.6% for a 300 ${\mu}m$ particle size at an inflow rate of 600 mL $s^{-1}$ with 23% of $R_f$. The maximum reduced grade efficiency (E'i) was 37.6% for a 300 ${\mu}m$ particle size at an inflow rate of 1,000 mL $s^{-1}$ with 11% of $R_f$. The results indicate that the separation performance of the LPH for suspended solids removal was size selective and that maximum removal occurred at particle sizes ranging from 300 to 500 ${\mu}m$.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.64-69
• /
• 2011

Porous manganese oxide porous nanostructures were prepared by amino-acid-mediated solvothermal self assembly reaction and subsequent heat treatment at $600^{\circ}C$. When Mn-precursors were heat-treated at $400-550^{\circ}C$, the sensors did not show significant gas responses. In contrast, the manganese oxide heat-treated at $600^{\circ}C$ showed the significant gas responses, that is, the resistance decrease to 100 ppm $C_3H_8$ ($R_a/R_g$ = 2.17, $R_a$ : resistance in air, $R_g$ : resistance in gas) and the resistance increase to 100 ppm $C_2H_5OH$ ($R_g/R_a$ = 1.92). The opposite change of resistance upon exposure to $C_3H_8$ and $C_2H_5OH$ was discussed in relation to the mixed phases of manganese oxides with different valences.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.181-184
• /
• 2002

본 논문에서는 600Hz 무선 LAN 시스템에 탑재를 위한 600㎓ 대역 전력증폭기 모듈을 개발 하였다. 600㎓ 대역 전력증폭기 모듈에 실장된 600㎓ 대역 전력증폭기 MMIC는 ETRI에서 설계 및 제작한 것으로 칩의 크기는 2.80 × 1.75㎟이며, on-wafer측정을 하여 얻은 결과는 동작 주파수 58~620Hz에서 소신호 이득은 12.4dB이고, 최대 소신호 이득은 59~60G보z에서 ISdB이며, 출력전력(Pldn)은 16.3~16.7dBm을 얻었다. 이와 같은 특성을 갖는 전력증폭기 MMIC를 사용하여 모듈을 제작하였으며, RF feed line을 위해 Rogers 사의 R03003 기판을 사용하였다. 모듈의 입출력은 동작 주파수 대역에 적합한 WRl5라는 waveguide 형태를 사용하였고, DC 바이어스 공급을 위해 3.5㎜ K-connector를 사용하였다 제작한 모듈의 크기는 40 × 30 × 15㎣이며, 최적의 성능을 얻고자 tuning bar를 상하로 이동하여 최적점을 찾았으며 나사로 고정하여 상태를 유지하도록 하였다. DC 바이어스 및 RF feed line과 칩의 연결은 본딩에 의한 인덕턴스를 최소화하기 위하여 3mil 두께의 리본 본딩을 하였다 전력증폭기 모듈을 측정한 결과, 동작주파수 600㎓ 대에서 소신호 이득은 6dB 이상, 입력 정합은 -lOdB 이하, 출력 정합은 -4dB 이하로 측정되었긴, 출력전력은 SdBm 이상으로 측정되었다. 동국대에서 제작한 600Hz 무선 LAN 시스템에 전력증폭기 모듈을 시스템 송신부에 탑재 시험한 결과, 동영상을 실시간으로 전송하는데 성공하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.290-295
• /
• 1992

Tendon driven method to drive one joint using two actuators is developed and implemented. While the method has advantages over conventional transmissions, it also has several drawbacks like tendon slack, elongation and endurability. In this paper, a compensation method of the intrinsic non-linearities of tendon is proposed to improve the performance of antagonistic tendon driven method. In this method, tendon tension measurement is prerequisite which is measured with strain gauge type tension sensor. The developed method is implemented on one link test bed with colocated and non-colocated position sensor.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.600-605
• /
• 2014

Two mufflers for a large-size sedan are suggested aiming (1) sporty-sound and (2) quiet-sound as well as both satisfying low back-pressure and low manufacturing cost. Transmission loss prediction considering heat and flow may increase the accuracy and reduce the development cost in muffler design; thus, GT-power prediction considering heat, flow, and acoustics is utilized. By understanding the fundamentals of flow-acoustic theory in small orifice(hole), an effective muffler design concept is proposed. Vehicle tests show the consistence with predictions for sound; also a back-pressure test bench confirms the advantage in pressure drop for both suggested mufflers. Those suggested mufflers also have advantages in manufacturing cost due to simplicity of the design.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.401-411
• /
• 2023

This study investigates the synthesis, characterization, and application of zinc oxide (ZnO) nanoparticles for corrosion resistance and stress corrosion cracking (SCC) mitigation in high-temperature and high-pressure environments. The ZnO nanoparticles are synthesized using plasma discharge in water, resulting in rod-shaped particles with a hexagonal crystal structure. The ZnO nanoparticles are applied to Alloy 600 tubes in simulated nuclear power plant atmospheres to evaluate their effectiveness. X-ray diffraction and X-ray photoelectron spectroscopy analysis reveals the formation of thermodynamically stable ZnCr₂O₄and ZnFe₂O₄ spinel phases with a depth of approximately 35 nm on the surface after 240 hours of treatment. Stress corrosion cracking (SCC) mitigation experiments reveal that ZnO treatment enhances thermal and mechanical stability. The ZnO-treated specimens exhibit increased maximum temperature tolerance up to 310 ℃ and higher-pressure resistance up to 60 bar compared to non-treated ZnO samples. Measurements of crack length indicate reduced crack propagation in ZnO-treated specimens. The formation of thermodynamically stable Zn spinel structures on the surface of Alloy 600 and the subsequent improvements in surface properties contribute to the enhanced durability and performance of the material in challenging high-temperature and high-pressure environments. These findings have significant implications for the development of corrosion-resistant materials and the mitigation of stress corrosion cracking in various industries.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.139-144
• /
• 2003

A flat type micro gas sensor was fabricated on the p-type silicon wafer with low stress Si$_3$N$_4$, whose thickness is 2 ${\mu}{\textrm}{m}$, using MEMS technology. WO$_3$ thin film as a sensing material for detection of NO$_2$ gas was deposited using a tungsten target by sputtering method, followed by thermal oxidation at several temperatures (40$0^{\circ}C$-$600^{\circ}C$) for one hour. NO$_2$ sensitivities were investigated for the WO$_3$ thin films with different annealing temperatures. The highest sensitivity was obtained for the samples annealed at $600^{\circ}C$ when it was operated at 20$0^{\circ}C$. The results of XRD analysis showed the annealed samples had polycrystalline phase mixed with triclinic and orthorhombic structures. The sample exhibits higher sensitivity when the system has less triclinic structure. The sensitivities, $R_{gas}/R_{air},$ operating at 20$0^{\circ}C$ to 5 ppm NO$_2$ of the sample annealed at $600^{\circ}C$ were approximately 90.

• Journal of Embryo Transfer
• /
• v.25 no.4
• /
• pp.291-295
• /
• 2010

Four estrus-induced Himalayan tahrs (Hemitragus jemlahicus) were inseminated with frozen-thawed semen by laparoscopic or transcervical insemination techniques with no regard to the site of ovulation in non-breeding season. In June and July, 2009, estrus was synchronized by Eazi-Breed $CIDR^{(R)}$ (Controlled internal drug release; Pfizer Animal Health, New Zealand) insertion for 16 days and PG 600 (PMSG 400IU, hCG 200 IU; Intervet, Netherlands) injection (IM) a day before removing $CIDR^{(R)}$. Forty eight hours later, laparoscopic or transcervical insemination was done to each of two tahrs under anesthetic condition inducted by ketamine (1.5 mg/kg) and medetomidine (0.09 mg/kg). For examination of estradiol and progesterone, blood was collected right before $CIDR^{(R)}$ insertion, PG 600 injection, $CIDR^{(R)}$ removal and insemination. Estradiol levels of four tahrs (No. 1, 2, 3, 4) before $CIDR^{(R)}$ insertion and insemination were 13.3, 8.8, 14.3, 12 pg/ml and 23.5, 25.5, 21.1, 11.5 pg/ml, respectively. Progesterone levels of four tahrs (No. 1, 2, 3, 4) before $CIDR^{(R)}$ insertion and insemination were 1.8, 0.05, 0.63, 0.61 ng/ml and 1.03, 0.37, 1.48, 2.12 ng/ml. Except for No. 4 tahr, cervices showed cervical mucus and opened enough to penetrate with embryo transfer gun sheet usually used for cows. Therefore, No.4 was laparoscopically inseminated together with No. 1. In conclusion, none of four Himalayan tahrs was pregnant. However, we proved that estrus could be induced by CIDR and PG 600 injection in non-breeding season, and laparoscopic or transcervical insemination with frozen-thawed semen could be one of assisted reproductive techniques in Himalayan Tahr.