• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.9
• /
• pp.877-880
• /
• 2009

A curing process in post-printing section of R2R process is required for an electrical property of the printed pattern when devices such as RFID, Solar cell are printed. PEN as well as heat-stabilized PET which is used as a plastic substrate would be deformed at high temperature due to change of its elastic modulus. And crack in the printed pattern, which is on the plastic substrate is occurred due to the deformation of the substrate. The occurrence of crack causes electrical resistance to increase and the quality of the device to deteriorate. In case of RFID antenna, the range of reading distance is shortened as the electrical resistance of the antenna is increased. Therefore, the deformation of the plastic substrate, which causes the occurrence of crack, should be minimized by setting up low operating tension in R2R process. In low tension, slippage between a moving substrate and a roller would be generated when the operating speed is increased. And scratch would be occurred when slippage is generated due to an air entrainment, which is related to the thickness of the air film. The thickness of the air film is increased when operating speed is increased as shown by simulation based on mathematical model. The occurrence of scratch in conductive pattern printed by roll to roll process is a critical damage because it causes degradation or failure of electrical property of it.

• Journal of Korea Foundry Society
• /
• v.40 no.2
• /
• pp.34-42
• /
• 2020

The effects of the initial balancing pressure, filling pressure and maximum build-up pressure on the casting characteristics of the thick-wall thickness casting during the counter-pressure casting process were investigated. Water model experiment and a computer simulation were carried out to evaluate the characteristics during the filling and solidification stages in counter-pressure casting (CPC); as a reference, the low-pressure casting (LPC) process was used. The average dendrite cell size decreased with an increase in the solidification rate and maximum build-up pressure. A turbulent flow occurred during the filling stage of the LPC process, resulting in the formation of inner gas, while a lamellar flow pattern dominated during the CPC process and was more evident with an increase in the initial balancing pressure, improving the mechanical properties of the castings.

• Korean Journal of Construction Engineering and Management
• /
• v.17 no.2
• /
• pp.31-38
• /
• 2016

In a construction project, the portion for maintenance costs for a building is considerable compared to the initial construction cost. As such, Life Cycle Cost (LCC) analysis is being increasingly utilized to assess the design value of engineering work in Korea. Additionally, the Public Procurement Service in Korea announced that it will be mandatory for all domestic construction projects to adopt BIM. Furthermore, the paradigm for architectural design has shifted from 2D to 3D, and to BIM, which includes a data management system. Within this background, however, there is currently no adequate BIM-based LCC analysis software and the requirements of cost estimation for repair and replacement cost for a building is not completely adequate in BIM tools such as Revit and Archicad. Therefore, this study suggests a process of cost estimation for repair and replacement (R&R) cost based on IFC data. First, we analyzed existing R&R criteria and defined BIM-based requirements when calculating R&R costs. These requirements were extracted from relevant IFC data. Subsequently, this was saved to a database and a BIM-based database was built for R&R cost estimation. Finally, this database was connected with external databases such as R&R Criteria DB and Cost Information DB to calculate R&R costs. This process is expected to improve upon the traditional process of cost estimation of R&R cost by applying a BIM model. The proposed process can contribute to a further standardizing of BIM-based LCC analysis thru application to initial construction costs, energy costs, and other maintenance costs.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.6
• /
• pp.51-57
• /
• 2012

This study investigated on the photolytic degradation of Triclosan by E-beam process. The optimization of process was investigated during a series of batch experiments by design of experiments(DOEs). The DOE was one of the statistical application that was used for designed the response surface to determine the effects of each parameters. The responses were applied as removal rate of Triclosan(%, $Y_1$) and TOC removal rate(%, $Y_2$). Two independent variables were concentration of Triclosan and irradiation intensity that were designed as "$x_1$" and irradiation intensity was designed as "$x_2$". The regression equation in coded parameter between the Triclosan removal efficiencies(%) and TOC removal efficiencies(%) was $Y_1=63-12.4335x_1+15.1835x_2+5.8125x{_1}^2-5.6875x{_2}^2-0.75x_1x_2(R^2=95.1%,\;R^2(Adj)=91.7%)$ and $Y_2=46-8.8462x_1+11.7175x_2-0.75x{_1}^2-6.25x{_2}^2(R^2=98.7%,\;R^2(Adj)=97.7%)$, respectively. The model predictions agreed well with the experimentally observed results $R^2$ and $R^2(Adj)$ over 90% within both of $Y_1$ and $Y_2$. This result shows that the regression model express well about the effects of parameters on E-beam process and the statistical method was successfully applied.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.113.1-113.1
• /
• 2011

PEMS (printed electro-mechanical system) is fabricated by means of various printing technologies. Passive and active compo-nents in 2D or 3D such as conducting lines, resistors, capacitors, inductors and TFT(Thin Film Transistor), which are printed withfunctional materials, can be classified in this category. And the issue of PEMS is applied to a R2R process in the manu-facturing process. In many electro-devices, the vacuum process is used as the manufacturing process. However, the vacuum process has a problem, it is difficult to apply to a continuous process such as a R2R(roll to roll) printing process. In this paper, we propose an ESD (electro static deposition) printing process has been used to apply an organic solar cell of thin film forming. ESD is a method of liquid atomization by electrical forces, an electrostatic atomizer sprays micro-drops from the solution injected into the capillary with electrostatic force generated by electric potential of about several tens kV. ESD method is usable in the thin film coating process of organic materials and continuous process as a R2R manufacturing process. Therefore, we experiment the thin films forming of PEDOT:PSS layer and active layer which consist of the P3HT:PCBM. The organic solar cell based on a P3HT/PCBM active layer and a PEDOT:PSS electron blocking layer prepared from ESD method shows solar-to-electrical conversion efficiency of 1.42% at AM 1.5G 1sun light illumination, while 1.86% efficiency is observed when the ESD deposition of P3HT/PCBM is performed on a spin-coated PEDOT:PSS layer.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.2 s.15
• /
• pp.41-46
• /
• 2006

Wet etching process in recent semiconductor manufacturing is devided into batch and single wafer type. Batch type wet etching process provides more throughput with poor etching uniformity compared to single wafer type process. Single wafer process achieves better etching uniformity by boom-swing injected chemical on rotating wafer. In this study, etching characteristics of $SiO_2$ layer at room and elevated temperature is evaluated and compared. The difference in etching rate and uniformity of each condition is identified, and the temperature profile of injected chemical is theoretically calculated and compared to that of experimental result. Better etching uniformity is observed with single wafer tool with boom-swing injection compared to single wafer process without boom-swing or batch type tool.

• Journal of Information Technology Services
• /
• v.12 no.2
• /
• pp.373-386
• /
• 2013

The purpose of this research is to develop a model for efficient service R&D investment in government budgeting process. It is necessary to develop an efficient and effective investment model to improve competitiveness of the service industry and national economy. Various existing types of service R&D classification have been reviewed. And object-oriented service R&D request classification types have been derived. A tentative model for evaluating service R&D requests have been developed through extensive discussions on effective methodologies. The model has been refined and revised by four service budgeting experts. The revised and refined checklists and guidelines have been used for 40 real service R&D requests evaluations. As a result, a full model for service R&D evaluation and budgeting has been proved to be useful. Also, a need for more efficient and concise evaluation model has been raised through this evaluation process. A brief model with only 10 checklists has been developed and its usefulness has been proven by pilot test with 10 real service R&D requests. The results of this study can be used for evaluation of service R&D proposals and effective budgeting of R&D requests for improving global competitiveness. Further research is needed for refining the developed evaluation models.

• Journal of Korean Institute of Industrial Engineers
• /
• v.43 no.2
• /
• pp.120-126
• /
• 2017

This paper has proposed the development direction and R&D analysis approach that the diversity of defense R&D process and product should be mainly under consideration. It has shown that there is a fair possibility of the various quality assess to meet the R&D requirements in defense-based. Thus, the analysis on multiple quality elements is carried out with defense R&D characteristics. Especially, a quality management master planning based on the quality model of establishing defense R&D policy has proposed, identifying relevant quality characteristics on the R&D of weapon system and the R&D of core technology. That is, this paper is not only interested in determining an appropriate model for improving the quality of a R&D weapon system but also argued efforts in order to reap the best possible outcome and process on both the R&D of weapon system and quality of the R&D of core technology including present R&D activities.

• Journal of the military operations research society of Korea
• /
• v.30 no.2
• /
• pp.122-132
• /
• 2004

The aim of this paper is to show the process of R&D Project-Priority Ordering in the Defense Technology field. We propose specific methods (Delphi, Analytic Hierarchy Process (AHP), Scoring) to order the R&D Project-Priority. In general, to decide the priority of R&D projects most of researches depend on questionnaires which are surveyed by experts. However, it is criticized that this process cannot reflect the limitation of experience and knowledge of experts. In this process, we separate evaluators in two parts: the first is strategic experts, the second is technical experts. Evaluators can choose and evaluate the alternatives which they are familiar with, so we can obtain reliable results. Finally, based on our process of the R&D Project-Priority Ordering we formulate policy implications for managing the defense technology.

• Korean Journal of Materials Research
• /
• v.1 no.2
• /
• pp.77-85
• /
• 1991

In this study we have investigated surface morphologies of as-deposited silicon films on the various deposition conditions using LPCVD(Low Pressure Chemical Vapor Deposition) System. The processing conditions such as deposition temperature, pressure and flow rate of $SiH_4$ gas were found to determine the surface morphology. The optimum temperature of maximum effective surface area increased with increasing the deposition pressure and the flow rate of $SiH_4$ gas, These experimental results were also in quite good agreement with the equation derived under the assumption that the maximum effective surface area is obtained on the condition of maximum nucleation rate.