• Land and Housing Review
• /
• v.3 no.4
• /
• pp.433-449
• /
• 2012

An experimental investigation was conducted to study the behavior of RC wide beam-column joints with slab subjected to reversed cyclic loads under constant axial load. Six half scale interior wide beam-column assemblies representing a portion of a frame subjected to simulated seismic loading were tested, including three specimens without slab and three specimens with slab. The primary variables were the ratio of column-to-beam flexural capacity ($M_r={\Sigma}M_c/{\Sigma}M_b$ ; 0.77~2.26), ratio of the column-to-beam width (b/H ; 1.54, 1.67). Test results are shown that (1) the current design code and practice for interior joints(type 2) are apply to the wide beam-high strength concrete column. (2) the presence of a slab have an effect on the performance of the wide beam-high strength concrete column interior joints(type 2). therefore in the design of the wide beam-high strength concrete column interior joints(type 2), the width of slab effective as a T beam flange should be considered. It was show that the case of the ratio of column-to-beam flexural capacity is more than 2.0, the effective width of slab are 2 times of an effective depth of wide beam, however if the ratio of column-to-beam flexural capacity is 1.4~2.0, the effective width of slab are not able to be considered.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.4
• /
• pp.464-476
• /
• 2019

Objectives: This study aimed to assess the exposure levels of tollbooth workers to diesel particulate matter using black carbon (BC) and to find the correlations among variables associated with BC using the motor vehicle management act regulated by the Ministry of Land, Infrastructure and Transport. Methods: This study was performed over 14 days at a university in Seoul. BC levels were monitored using an aethalometer and were conducted around the breathing zones of the workers. There were three sampling locations: inside the tollbooth (front gate and rear gate) and an office as a control group. T-test, correlation, and multiple linear regression analysis were performed using SPSS. Results: The geometric mean (GM) of BC_30min concentrations in the exposure group was 2.44 ㎍/㎥, approximately 1.4 times higher than the control group (1.75 ㎍/㎥). The GM of BC_30min concentrations was 2.75 ㎍/㎥ during the heavy traffic time (9-10 am) and 2.30 ㎍/㎥ during non-heavy traffic times (p<0.001). The multiple linear regression analysis shows that the number of all types of vehicles and PM_2.5 concentrations in the atmosphere were factors increasing the GM of BC(ln(BC_30min)) concentrations (adjusted R²=0.42, p<0.001). The workers were constantly exposed to low concentrations (GM of BC_30min=2.44 ㎍/㎥), but they were exposed to peak concentrations instantly (BC_10sec=3545.04 ㎍/㎥). When the GM of BC_30min concentrations was momentarily represented as high, it was identified that a vehicle mainly using diesel fuel or an aging vehicle had passed. Conclusions: A ventilation system should be installed in the closed tollbooth or aging vehicles should be controlled so as not to pass tollbooths.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.133-140
• /
• 2017

This study investigates the oxidation properties of Fe-14Cr ferritic oxide-dispersion-strengthened (ODS) steel at various high temperatures (900, 1000, and $1100^{\circ}C$ for 24 h). The initial microstructure shows that no clear structural change occurs even under high-temperature heat treatment, and the average measured grain size is 0.4 and $1.1{\mu}m$ for the as-fabricated and heat-treated specimens, respectively. Y-Ti-O nanoclusters 10-50 nm in size are observed. High-temperature oxidation results show that the weight increases by 0.27 and $0.29mg/cm^2$ for the as-fabricated and heat-treated ($900^{\circ}C$) specimens, and by 0.47 and $0.50mg/cm^2$ for the as-fabricated and heat-treated ($1000^{\circ}C$) specimens, respectively. Further, after 24 h oxidation tests, the weight increases by 56.50 and $100.60mg/cm^2$ for the as-fabricated and heat-treated ($1100^{\circ}C$) specimens, respectively; the latter increase is approximately 100 times higher than that at $1000^{\circ}C$. Observation of the surface after the oxidation test shows that $Cr_2O_3$ is the main oxide on a specimen tested at $1000^{\circ}C$, whereas $Fe_2O_3$ and $Fe_3O_4$ phases also form on a specimen tested at $1100^{\circ}C$, where the weight increases rapidly. The high-temperature oxidation behavior of Fe-14Cr ODS steel is confirmed to be dominated by changes in the $Cr_2O_3$ layer and generation of Fe-based oxides through evaporation.

• Applied Biological Chemistry
• /
• v.45 no.2
• /
• pp.59-65
• /
• 2002

Different amounts of the Opuntia ficus-indica var. saboten fruit were soaked in different alcohol concentrations of a Korean rice wine distillate for 4 months. Changes in pH, brix degree, contents of reducing sugar and polyphenol compound, alcohol concentration, turbidity, and color were analyzed during the soaking period. Quality of the final product was determined through the analysis of the volatile flavor compounds and sensory evaluation. During the soaking periods, pH, alcohol concentration, and contents of polyphenol compound decreased, whereas the content of reducing sugar increased. These changes were affected more by the content of the fruit than the alcohol concentration of the soaking media. Turbidity of the wine increased with higher fruit contents, while the increase of alcohol concentration resulted in the turbidity decrease. As the soaking period increased, lightness and yellowness increased but redness decreased. Acetaldehyde, acetyl acetone, ethyl alcohol, guaiacol, thymol, and acetic acid phenyl ester were detected in all liquors. Significant differences in all sensory attributes test were shown by six experimental groups (p<0.05), and the best overall acceptability was obtained from the liquor made of 67% fruits and 30% alcohol concentration.

• Korean Journal of Clinical Laboratory Science
• /
• v.38 no.1
• /
• pp.16-21
• /
• 2006

Parallel testing means ordering a number of tests at the same time so abnormalities in any of the tests can be found quickly and used in making the diagnosis. This is a good medical strategy to eliminate diseases and it is relatively inexpensive if all the tests are potential sources of information and performed on the same analyzer. In regression, the equation for the straight line is recast as y = bx + a. This change in terminology leads to confusion. Here a is the y-intercept or constant and b is the coefficient or slope of the line. A few more words of caution about regression - as in all of statistics there are certain assumptions: the x value is a true measure, both X and Y distributions are normal, and homoscedasticity, i.e., the variance of y is the same for each value of x. In this study the linearity classification made by different scientists were always in agreement. Typical examples of curves that were considered linear are presented in Fig. 1-5. Because these automated procedures values were usually within five percent of each other the curvature could be easily detected. The plot of the WBC, RBC, hemoglobin, hematocrit and platelet concentrations from approximately 74.4 to $0{\times}10^3/{\mu}L$ and $80.4-0{\times}10^3/{\mu}L$, $5.6-0{\times}10^6/{\mu}L$ and $6.1-0{\times}1106/{\mu}L$, 18.3-0 g/dL and 19.0-0 g/dL, 54.1-0% and 56.8-0% and 642.0 to $0.03{\times}10^3{\mu}L$ and $754.0-0{\times}10^3/{\mu}L$ on the ADVIA 2120 C Versus and A and B typical of an acceptable linear study as shown in Fig. 1-5. The grand mean of R2, intercept and slope is 0.99898, 0.99459 and 1.54626.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.144-155
• /
• 1997

This study evaluated shear bond strength between porcelain and resin cement according to various surface treatments of porcelain, and surface condition of debonded porcelain. 50 porcelain specimens(Celay block A2M7) and composite resin specimens(Clearfil Photo-Bright) were prepared, and divided into 5 experimental groups according to the treatment method of porcelain surface. 5 experimental groups by surface treatments were as follows; CONTROL Group : No surface treatment was done on the surface of porcelains. SAND Group : The surface of porcelains were sandblasted with $50{\mu}m$ aluminum oxide for 5 seconds. HF Group: The surface of porcelains were etched with 8% Hydrofluoric acid for 4 minutes. SIL Group: The surface of porcelains were coated with silane coupling agent and heated at $100^{\circ}C$ for 5 minutes. SAND+HF+SIL Group : The surface of porcelains were sandblasted with $50{\mu}m$ aluminum oxide for 5 seconds and etched with 8% Hydrofluoric acid for 4 minutes, and coated with silane coupling agent and heated at $100^{\circ}C$ for 5 minutes. After surface treatments on the prepared porcelain surface two pastes of Panavia 21$^{(R)}$ were mixed, they were applied between composite resin block and porcelain surface, and then excessive resin cements were removed, and its margin was surrounded with Oxyguard II. All specimens were stored for 24 hours in water at $37^{\circ}C$ and tested with Instron testing machine between porcelains and resin cements, and debonded porcelain surfaces were observed under Scanning Electon Microscope(Hitachi S-2300) at 20kvp. The values from each group were compared statistically by Student's t-test. The obtained results were as follows; 1. The shear bond strength without surface treatment of porcelain was the lowest among all experimental groups(p<0.05). 2. The detached porcelain surface with sandblasting alone had more remarkable cracks than with only Hydrofluoric Acid or Silane coupling 2gent, but showed the lowest value of shear bond strength among surface treated groups(p<0.05), 3. When porcelain surface was treated by hydrofluoric acid, it affected shear bond strength more than silane coupling agent, but there were no significant statistical differences(p>0.05). 4. When three methods were combined to increase shear bond strength between porcelains and resin cements, its value was the highest than the others(p<0.05). 5. In Scannig Electron Micrograph of detached porcelain surface with no treatment, the sample revealed adhesive failure between the porcelain and resin cement whereas detached porcelain surface with combination of three method cohesive failure on the porcelain.

• Journal of Korean Academic Society of Home Health Care Nursing
• /
• v.2
• /
• pp.19-34
• /
• 1995

The purpose of this study was to analysis level on family caregiver's burden for the elderly with chronic disease in a rural area and to choose priority care group, thereby facilitating the development of interventions to reduce the caregiver's burden. For this purpose, data were collected by questionaire from June 10 to October 8, 1994. The instruments for data collection were Caregiver Burden Inventory by Novak(1989) and Zarit et al(1982), severity of dementia by Hughes Scales(1982), ADL by Lawton(1971), patients' family caregiving activity by pre-survey and reference review(Lee, 1993 ; Jang, 1990 ; Yoo, 1982). The subjects were 213 family caregiver of elderly with chronic disease in a rural area. The data was analysed by the use of t-test, ANOVA, correlation and multiple regression. The results were as follows ; 1. Total burden was evaluated below average, the mean of family burden was 46.98. By the diagnostic classification, Hypertension was 27.37, DM 32.46, CVA 62.96, Dementia 61.24. 2. Significant variables which were correlated to the family caregiver's burden were the patient's disease diagnosis (F=33.82, p<0.001), severity of dementia(F=30.52, p<0.001), the status of disease management(F=11.53, p<0.001), ADL(F=10.54, p<0.001), PADL(F=7.50, p<0.001), income(F=7.17, p<0.001), caregiver's health status(F=24.53, p<0.001), a view of patient's prognosis (F=22.17, p<0.001), relationship with the patient(F=33.82, p<0.001), the number of hours per day spent on caregiving(F=77.52, p<0.001), level of intimacy of caregiver and patients(F=8.75, p<0.001), level of helping(F=4.90, p<0.01), the frequency of caregiving activity(F=3.80, p<0.01), the number of admission(F=5.54, p<0.01), the length of caregiving(F=4.43, p<0.01), other chronic patient in family(t=2.81, p<0.01), caregiver's job(F=3.11, p<0.01), the duration of illness(F=2.98, p<0.05), caregiver's religion(F=2.93, p<0.05), medical security(F=3.89, p<0.05), caregiving's helper(t=2.42, p<0.05). 3. PADL was the most important predictor to family caregiver burden(R2=0.6611). In addition to this, IADL, caregiver's health status, the length of caregiving. level of intimacy of caregiver and patients, patient's age, the patient's disease diagnosis and patient's job accounted for 76% of family caregiver burden. 4. The criteria of priority care group were as follows ; the mean of family caregiver burden was above 58, above of moderate ADL, the number of hours per day spent on caregiving above of 8 hours, above of moderate dementia. By the diagnostic classification, number of priority care group, Hypertension was 4 (8.0%), DM 4(8.0%), CVA 34(64.1%), Dementia 45(75.0%).

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.2
• /
• pp.350-361
• /
• 1996

The objectives of this study mere 1) to investigate whether the different nonwoven fabric types influenced on the objective and subjective wear performances of the experimental pesticide protective pants, 2) to detect whether the different finishes treated to the nonwoven fabrics influenced on the objective and subjective wear performances of the experimental pants, and 3) to detect the relationships between objective wear performances and subjective wear sensation. Three types of nonwoven fabrics (T (Tyvek$\textregistered$), 5 (Sontara$\textregistered$) and K (Kimlon$\textregistered$)) were used as test specimens. By pad-dry.cure method, each of the specimen was treated with fluorocarbon compound for water-oil repellent finish (Tw, Sw, Kw). And each of specimen was treated with organic silicon quarternary ammonium salts and then treated with fluorocabon compound for dual functional finish (76, 50, Kd). Using the three water-oil repellent finished fabrics and the three dual functional finished fabrics, six experimental protective pants (Cl (Tw), C2 (Sw), C3 (Kw), C4 (76), C5 (56), C6 (Kd)) were made according to the same pattern suggested by the Rual Guidance Office. The wear trials of experimental pesticide protective pants were performed in a conditioned vinyl plastic hothouse ($30\pm1^{\circ}C$, $70\pm5%$R.H., 0.25m/sec air velocity). The measurements of skin temperature, microclimate temperature and humidity on the subjects were obtained by the themohygromenter. The subjective wear sensations were measured using previously developed thermal, humidity and overall comfort scales. The results obtained from this study were as follows: 1) There were siginificant differences among nonwoven fabric types on the objective and subjective wear performances, therefore, the skin temperature, microclimate temperature and humidity of subjects who wore the experimental pants made with Sontara were siginificantly lower than those who wore the others. And, the experimental pants made with Sontara were assessed as more comfortable than the others in terms of the subjective thermal, humidity and overall wear sensations. 2) There were no significant differences between two finish types on the objective and subjective wear Performances. 3) The microclimate humidity on the thigh was highly correlated with the overall subjective comfort sensations and the next highly correlated one was the mean skin temperature. That is, the higher the microclimate humidity and the mean skin temperature, the higher the overall subjective comfort sensation ratings which mean the overall subjective sensation was very uncomfortable.

• Journal of Korean society of Dental Hygiene
• /
• v.13 no.2
• /
• pp.351-360
• /
• 2013

Objectives : The purpose of this study was to evaluate the effects of tooth bleaching agent contained 15% carbamide peroxide on the color, microhardness and surface roughness of tooth-colored restorative materials by using pH cycling model. Methods : Four types of tooth-colored restorative materials, including a composite resin(Filtek Z350 ; Z350), a flowable composite resin(Filtek P60 : P60), a compomer(Dyract$^{(R)}$ AP ; DY), and a glass-ionomer cement(KetacTM Molar Easymix ; KM). were used in the study. Eighty-eight specimens of each material were fabricated, randomly divided into two groups(n=44): experimental group(15% carbamide peroxide) and control group(distilled water). These groups were then divided into four subgroups(n=11). All groups were bleached 4 hours per day for 14 days using pH cycling model. The authors measured the color, microhardness, and roughness of the specimens before and after bleaching. The data were analyzed with ANOVA and T-test. Results : Z350 and P60 showed a slight color change(${\Delta}E^*$), whereas DY and KM showed significantly color change(p<0.05). Among them, the greatest color change was observed in DY. Percentage microhardness loss(PML) of the distilled water group was 1.8 to 5.1%, and 15% peroxide peroxide group was 5.0 to 25.2%. Microhardness of DY and KM showed a statistically significant decrease(p<0.05). Roughness was increased in all groups after bleaching. Z350 and P60 does not have a significant difference(p>0.05), however DY and KM significantly increased more than the 0.2 ${\mu}m$(p<0.05). Conclusions : The effects of bleaching on restorative materials were material dependent. It is necessary to consider the type of the material before starting the treatment.

• Analytical Science and Technology
• /
• v.29 no.5
• /
• pp.234-241
• /
• 2016

The approach presented in this article refers to the bioanalytical method validation for the detection and quantitative determination of arsenic species including arsenite (As(III)), arsenate (As(V)), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) in dog plasma by high-performance liquid chromatography inductively coupled plasma mass spectrometry (HPLC-ICP/MS). The arsenic species were separated using an agilent As speciation column by a mobile phase of 2 mM sodium phosphate monobasic, 0.2 mM ethylenediaminetetraacetic acid disodium salt dehydrate, 10 mM sodium acetate, 3 mM sodium nitrate and 1 % ethyl alcohol at pH 11 (adjusted with 1M NaOH). The method validation experiment was obtained selectivity, linearity, accuracy, precision, matrix effect, recovery, system suitability, dilution integrity and various stabilities. All calibration curves showed good linearity (R²>0.999) within test ranges. The lower limit of quantitation (LLOQ) was 5 ng/mL for As(III), As(V) and DMA, and 20 ng/mL for MMA. The system suitability and dilution values were within 6.5 % and 7.7 %. Subsequently, the developed and validated HPLC-ICP/MS method was also successfully applied to determine the arsenic speciation in dog plasma samples, and the recoveries for the spiked samples were in the range of 91.5–102.2 %. Therefore, this method could be applied to the evaluation of arsenic exposure, health effect assessment and other bio-monitoring studies in biological samples.