• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.2
• /
• pp.230-239
• /
• 2012

In this paper, we present the radio-frequency (RF) modeling for gate-all-around (GAA) junctionless (JL) MOSFETs with 30-nm channel length. The presented non-quasi-static (NQS) model has included the gate-bias-dependent components of the source and drain (S/D) resistances. RF characteristics of GAA junctionless MOSFETs have been obtained by 3-dimensional (3D) device simulation up to 1 THz. The modeling results were verified under bias conditions of linear region (VGS = 1 V, VDS = 0.5 V) and saturation region (VGS = VDS = 1 V). Under these conditions, the root-mean-square (RMS) modeling error of $Y_{22}$-parameters was calculated to be below 2.4%, which was reduced from a previous NQS modeling error of 10.2%.

• Structural Engineering and Mechanics
• /
• v.26 no.5
• /
• pp.499-516
• /
• 2007

An experimental method denoted as Impulse Method is proposed as a cost-effective non-destructive technique for the on-site evaluation of concrete elastic modulus in existing structures: on the basis of Hertz's quasi-static theory of elastic impact and with the aid of a simple portable testing equipment, it makes it possible to collect series of local measurements of the elastic modulus in an easy way and in a very short time. A Hypothesis Testing procedure is developed in order to provide a statistical tool for processing the data collected by means of the Impulse Method and assessing the possible occurrence of significant variations in the elastic modulus without exceeding some prescribed error probabilities. It is based on a particular formulation of the renowned sequential probability ratio test and reveals to be optimal with respect to the error probabilities and the required number of observations, thus further improving the time-effectiveness of the Impulse Method. The results of an experimental investigation on different types of plain concrete prove the validity of the Impulse Method in estimating the unknown value of the elastic modulus and attest the effectiveness of the proposed Hypothesis Testing procedure in identifying significant variations in the elastic modulus.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.6
• /
• pp.521-531
• /
• 2020

QZSS (Quasi-Zenith Satellite System) provides the CLAS (Centimeter Level Augmentation Service) through the satellite's L6 band. CLAS provides correction messages called C-SSR (Compact - State Space Representation) for GPS (Global Positioning System), Galileo and QZSS. In this study, CLAS messages were received by using the AsteRx4 of Septentrio which is a GPS receiver capable of receiving L6 bands, and the messages were decoded to acquire C-SSR. In addition, Multi-GNSS (Global Navigation Satellite System) Code-PPP (Precise Point Positioning) was developed to compensate for GNSS errors by using C-SSR to pseudo-range measurements of GPS, Galileo and QZSS. And non-linear least squares estimation was used to estimate the three-dimensional position of the receiver and the receiver time errors of the GNSS constellations. To evaluate the accuracy of the algorithms developed, static positioning was performed on TSK2 (Tsukuba), one of the IGS (International GNSS Service) sites, and kinematic positioning was performed while driving around the Ina River in Kawanishi. As a result, for the static positioning, the mean RMSE (Root Mean Square Error) for all data sets was 0.35 m in the horizontal direction ad 0.57 m in the vertical direction. And for the kinematic positioning, the accuracy was approximately 0.82 m in horizontal direction and 3.56 m in vertical direction compared o the RTK-FIX values of VRS.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1733-1736
• /
• 2005

Many studies have been carried out to produce 3D features in the size range between $10{\mu}m\~10,000{\mu}m$, called Meso-scale. If these miniaturized systems have high relative accuracy and good volumetric utilization, it is possible to manufacture more complex and accurate shapes with various materials as well as there are advantages of reducing energy, space and resources. Due to imperfect components and misalignment in assembly, it is necessary to assess the accuracy of the miniaturized system itself to obtain high relative accuracy. Laser interferometers are widely used to measure geometric errors called as quasi-static errors. For miniaturized system, however, it is difficult to install the required accessories such as optics and the measuring range is limited because of the size of the system and also this method is very expensive. Moreover, it is impossible to measure each error component simultaneously. A new system to measure simultaneously multiple geometric errors is proposed using capacitance sensors. Each error was measured using capacitance sensors and a measurement algorithm was mathematically derived. The experiments show that the proposed measurement system can be used effectively to assess the accuracy of miniaturized system at a low cost.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.33-38
• /
• 2008

Most structures of vehicle are composed of many substructures connected to one another by various types of mechanical joints. In vehicle engineering, it is important to study these jointed structures under random frequency vibration for the evaluations of fatigue life and stress concentration exactly. It is rarely obtained the accurate load history of specified positions in a jointed structure because of the errors such as modeling, measurement, and etc. In the beginning of design, exact load data are actually necessary for the fatigue strength and life analysis to minimize the cost and time of designing. In this paper, the hybrid method of practical dynamic load determination is developed by the combination of the principal stresses from F. E. Analysis and test of a jointed structure. Least square pseudo inverse matrix is adopted to obtain an inverse matrix of analyzed stresses matrix. The error minimization method utilizes the inaccurate measured error and the shifting error that the whole data is stiffed over real data. The least square criterion is adopted to avoid these errors. Finally, to verify the proposed system, a heavy-duty bus is analyzed. This measurement and prediction technology can be extended to the different jointed structures.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2008.11a
• /
• pp.91-94
• /
• 2008

본 논문에서는 준 정적(quasi-static) 레일레이 페이딩(Rayleigh fading) 채널에서 상향링크 다중 사용자 MIMO-OFDM 시스템을 위한 최소평균제곱오차-순차간섭제거(MMSE-SIC: Minimum mean square error-successive interference cancellation) 수신기에 대해 연구한다. 송신 안테나가 하나인 사용자와 수신 안테나가 다수인 기지국에서 MMSE-SIC 수신기를 기반으로 신호를 검출하는 시스템에서는 하나의 부대역 내에서 동시에 전송 가능한 사용자의 수가 기지국에서의 수신안테나 수보다 작아야 하는 제한 조건을 가지고 있다. 따라서 사용자간 공정성을 보장하고 시스템의 효율성을 높이기 위해 낮은 복잡도를 가지는 비례 공정(Proportional fair) 스케줄링 알고리즘을 제안한다. 제안된 비례 공정 스케줄링 알고리즘에서는 부대역 내에서 다중 사용자 채널 행렬을 기반으로 동시에 전송하는 사용자들의 집합을 찾는다. 평균 채널 이득이 사용자마다 다른 환경에서의 모의실험을 통해 제안된 비례 공정 스케줄링 기법의 성능을 알아본다. 제안된 비례 공정 스케줄링 기법은 기존의 공정성을 기반으로 하는 스케줄링 알고리즘보다 더 큰 일반 비례 공정(General proportional fair) 기준과 더 높은 셀 수율(Cell throughput)을 가지는 것을 보이고 있다.

• International Journal of Contents
• /
• v.11 no.1
• /
• pp.7-14
• /
• 2015

In this paper, we derive the outage probability for M-ary phase shifting keying (MPSK) and M-ary quadrature amplitude modulation (MQAM) burst transmission (BT) of adaptive decode-and-forward (ADF) cooperative relay systems over quasi-static Rayleigh fading channels. Within a burst, there are pilot symbols and data symbols. Pilot symbols are used for channel estimation schemes and each relay node's transmission mode selection schemes. At first, we focus on ADF relay systems in which the probability density function (PDF) is derived on the basis of error events at relay nodes corresponding to channel estimation errors. Next, the average outage probability is derived as an approximate expression for an arbitrary link signal-to-noise ratio (SNR) for different modulation orders. Its accuracy is demonstrated by comparison with simulation results. Further, it is confirmed that BT-ADF relay systems with pilot symbol based channel estimation schemes enables to select correctly decoded relay nodes without additional signaling between relay nodes and the destination node, and it is verified that the ideal performance is achieved with small SNR loss.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1799-1802
• /
• 2003

The commercial success of a new product is influenced by the time to market. Shorter product leadtimes are of importance in a competitive market. This can be achieved only if the product development process can be realized in a relatively small time period. New cutting inserts are developed by a time consuming trial and error process guided by empirical knowledge of the mechanical cutting process. The effect of previous cutting on chip formation and the surface residual stresses has been studied. The chip formation is not affected much. There is only a minor influence from the residual stress on the surface from tile first cutting on the second pass chip formation. Thus, it is deemed to be sufficient to simulate only the first pass. The influence of the cutting speed and feed on the residual stresses has been computed and verified by the experiments. It is shown that the state of residual stresses in the workpiece increases with the cutting speed. This paper presents experimental results which can be used for evaluating computational models to assure robust solutions. The general finite element code ABAQUS/Standard has been used in the simulations. A quasi-static simulation with adiabatic heating was performed. The path for separating the chip from the workpiece is predetermined. The agreement between measurements and calculation is good considering the simplifications introduced.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.9
• /
• pp.24-29
• /
• 2010

This paper presents the RF modeling for silicon nanowire MOSFET with 30 nm channel length and 5 nm channel radius. Equations for analytical parameter extraction are derived by analysis of Y-parameter. Accuracies of the new model and extracted parameters have been verified by 3-dimensional device simulation data up to 100 GHz. The model verifications are performed under conditions of saturation region ($V_{gs}$ = $_{ds}$ = 1 V) and linear region ($V_{gs}$ = 1 V, $V_{ds}$ = 0.5 V). The RMS modeling error of Y-parameters was calculated to be 1 %.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.331-338
• /
• 2018

Electrohydraulic forming (EHF) process is a high speed forming process that utilizes the electric energy discharge in fluid-filled chamber to deform a sheet material. This process is completed in a very short time of less than 1ms. Therefore, finite element analysis is essential to observe the deformation mechanism of the material in detail. In addition, to perform the numerical simulation of EHF, the material properties obtained from the high-speed status, not quasi static conditions, should be applied. In this study, to obtain the parameters in the constitutive equation of Al 6061-T6 at high strain rate condition, a surrogate model using an artificial neural network (ANN) technique was employed. Using the results of the numerical simulation with free-bulging die in LS-DYNA, the surrogate model was constructed by ANN technique. By comparing the z-displacement with respect to the x-axis position in the experiment with the z-displacement in the ANN model, the parameters for the smallest error are obtained. Finally, the acquired parameters were validated by comparing the results of the finite element analysis, the ANN model and the experiment.