• 한국방재학회 논문집
• /
• 제7권1호통권24호
• /
• pp.11-20
• /
• 2007

본 연구에서는 H형 기둥-보 접합부에서 스캘럽 주변의 파단을 피하기 위해 스캘럽을 생략하고 보와 기둥의 쉬어탭을 볼트로 체결한 후 보 플랜지의 양면에 커버 플레이트와 리브로 보강하는 방법을 제안하였다. 스캘럽을 생략함으로써 스캘럽에서의 응력집중의 빈도를 줄이고 용접부 주위에서의 취성파괴를 방지하여 건축물의 내진성능을 향상시키는데 본 연구의 목적을 둔다. 본 목적을 위해 총 4개의 실험체를 제작하고 반복 가력 실험을 실시하였다. 주요 실험변수는 패널존 강도비이고 실험체의 항복강도, 초기강성, 총소성회전에 대한각 부재의 기여도, 에너지 소산능력으로부터 제작된 실험체들이 특수모멘트골조 내진규정에 만족을 하는지와 실험에 사용된 변수에 대한 여러 영향을 밝히고자 하였다. 그 결과 모든 실험체는 층간변위 4%, 총소성회전 0.03rad.에 충분이 도달하여 1997 AISC의 내진규정에 따라 특수모멘트골조에 만족할 것이라 판단된다.

• Elastomers and Composites
• /
• 제42권3호
• /
• pp.168-176
• /
• 2007

카본블랙이나 실리카 등으로 보강된 고무 가황체는 순수한 초기상태에서 하중(부하)를 가하고 제거하는 반복과정에서 응력은 점점 연화되어 초기상태에서 얻어진 응력보다 작게 나타난다. 이러한 응력 연화 현상을 Mullins 효과라고 부른다. 이러한 응력 연화 거동을 이론적으로 표현하기 위하여 Ogden-Roxburgh 등이 손상 파라미터를 이용하여 제안한 pseudo-elastic 개념을 적용하여 보강제가 함유된 고무 가황체의 변형률 에너지 함수를 구하였다. 카본블랙으로 보강된 NR 가황체를 이용하여 준정적 반복 부하 시험을 실시하였으며, pseudo-elastic 모델에서의 손상 파라미터가 제하 및 재 부하 시 응력-변형률 곡선에 어떠한 영향을 주는가와 더불어 손상 파라미터의 두 가지 변수인 r과 m의 물리적 의미를 파악하였다. 또한 보강제 함량을 달리하여 제작한 고무 가황체의 응력연화 변형률 에너지 함수를 결정하고 비교하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.703-712
• /
• 2004

A variant of the magnetoplasma jet engine (magjet) is here proposed for airbreathing flight in the hypersonic regime. As shown in Figure 1, the engine consists of two distinct ducts: the high-speed duct, in which power is added electromagnetically to the incoming air by a momentum addition device, and the fuel cell duct in which the flow stagnation temperature is reduced by extracting energy through the use of a magnetoplas-madynamic (MPD) generator. The power generated is then used to accelerate the flow exiting the fuel cells with a fraction bypassed to the high-speed duct. The analysis is performed using a quasi one-dimensional model neglecting the Hall and ion slip effects, and fix-ing the fuel cell efficiency to 0.6. Results obtained show that the specific impulse of the magjet is at least equal to and up to 3 times the one of a turbojet, ram-jet, or scramjet in their respective flight Mach number range. Should the air stagnation temperature in the fuel cell compartment not exceed 5 times the incoming air static temperature, the maximal flight Mach number possible would vary between 6.5 and 15 for a magnitude of the ratio between the Joule heating and the work interaction in the MPD generator varied between 0.25 and 0.01, respectively. Increasing the mass flow rate ratio between the high speed and fuel cell ducts from 0.2 to 20 increases the engine efficiency by as much as 3 times in the lower supersonic range, while resulting in a less than 10% increase for a flight Mach number exceeding 8.

• 한국위성정보통신학회논문지
• /
• 제5권1호
• /
• pp.80-84
• /
• 2010

위성 구조계의 가장 기본적인 임무 및 역할은, 우선 위성 자체의 미션 및 기능을 위해 필요한 여러 탑재체 및 장비들을 장착하고 지지할 수 있는 공간을 제공하고, 발사 시에 발생하는 이런 극심한 발사환경 하중에서 위성체 및 탑재체들을 안전하게 보호하는 것이다. 위성체가 발사체에 실려 발사될 때에 매우 높은 가속도에 의한 정적하중 및 공기의 저항에 의한 하중, 연소 가스 분출 시 발생하는 음향에 의한 하중, 발사체로부터 분리될 때 발생하는 충격 하중 등 여러 가지의 극심한 하중을 겪게 된다. 이런 여러 발사환경 중, 저주파 동적 하중 환경의 검증을 위한 정현파 가진 시험 시에 주요 탑재체 및 장비들의 고유모드에서 과도한 하중이 가해지는 것을 피하기 위해 정현파 가진 규격에 노칭을 적용하게 된다. 본 논문은 정현파 가진 시험을 주요 내용으로 하며, 시험을 수행하기 위한 노칭된 예측 입력하중과 실제 시험에 사용된 입력하중을 비교하여 유한요소모델 및 예측의 정확성을 확인해 보고자 한다.

• Structural Engineering and Mechanics
• /
• 제74권3호
• /
• pp.351-363
• /
• 2020

Based on the dynamic tests of recycled aggregate concrete (RAC) short columns confined by the hoop reinforcement, the dynamic failure mechanism and the mechanical parameters related to the constitutive relation of confined recycled aggregate concrete (CRAC) were investigated thoroughly. The fracturing sections were relatively flat and smooth at higher strain rates rather than those at a quasi-static strain rate. With the increasing stirrup volume ratio, the crack mode is transited from splitting crack to slipping crack constrained with large transverse confinement. The compressive peak stress, peak strain, and ultimate strain increase with the increase of stirrup volume ratio, as well as the increasing strain rate. The dynamic confining increase factors of the compressive peak stress, peak strain, and ultimate strain increase by about 33%, 39%, and 103% when the volume ratio of hoop reinforcement is increased from 0 to 2%, but decrease by about 3.7%, 4.2%, and 9.1% when the stirrup spacing is increased from 20mm to 60mm, respectively. This sentence is rephrased as follows: When the stirrup volume ratios are up to 0.675%, and 2%, the contributions of the hoop confinement effect to the dynamic confining increase factors of the compressive peak strain and the compressive peak stress are greater than those of the strain rate effect, respectively. The dynamic confining increase factor (DCIF) models of the compressive peak stress, peak strain, and ultimate strain of CRAC are proposed in the paper. Through the confinement of the hoop reinforcement, the ductility of RAC, which is generally slightly lower than that of NAC, is significantly improved.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1336-1349
• /
• 2018

Generally, a precast prestressed concrete (PSC) beam is used as girders for short-to-medium span (less than 30 m) bridges due to the advantages of simple design and construction, reduction of construction budget, maintenance convenience. In order to increase the span length beyond 50 m of precast PSC girder, PSC hollow box girder with unbonded prestressed H-type steel beam placed at the compressive region is proposed. The unbonded compressive prestressing in the H-type steel beams in the girder is made to recover plastic deflection of PSC girder when the pre-stressing is released. Also, the H-steel beams allow minimization of depth-to-length ratio of the girder by reducing the compressive region of the cross-section, thereby reducing the weight of the girder. A quasi-static 3-point bending test with 4 different loading steps is performed to verify safety and plastic deflection recovery of the girder. The experimental results showed that the maximum applied load exceeded the maximum design load and most of the plastic deflection was recovered when the compressive prestressing of H-type steel beams is released. Also using prestressed H-type steel as compression reinforcements in the upper part of cross section, repair and restoration difficulty and cost of PSC girders should be significantly reduced. The study result and analysis are discussed in detail in the paper.

• Steel and Composite Structures
• /
• 제41권5호
• /
• pp.663-679
• /
• 2021

To elucidate the differences in the collapse behavior between a single-story beam-column assembly and multi-story frame, two 1/3-scale two-bay composite frames, including a single-story composite beam-column assembly and a three-story composite sub-frame, were designed and quasi-statically tested. The load-displacement responses, failure modes, and internal force development of the two frames were analyzed and compared in detail. Furthermore, the resistance mechanisms of the two specimens were explored, and the respective contributions of different load-resisting mechanisms to the total resistances were quantitatively separated to gain deeper insights. The experimental tests indicated that Vierendeel action was present in the two-dimensional multi-story frames, which led to an uneven internal force distribution among the three stories. The collapse resistance of TSDWA-3S in the flexural stage was not significantly increased by the structural redundancy provided by the additional story, as compared to that of TSDWA-1S. Although the development of the load response was similar in the two specimens at flexural stage, the collapse mechanisms of the multi-story composite frame were much more complicated than those of the single-story beam-column assembly, and the combined action between stories was critical in determining the internal force redistribution and rebalancing of the remaining structure.

• Steel and Composite Structures
• /
• 제44권4호
• /
• pp.503-517
• /
• 2022

This paper presents the mechanical buckling of bi-directional functionally graded sandwich beams (BFGSW) with various boundary conditions employing a quasi-3D beam theory, including an integral term in the displacement field, which reduces the number of unknowns and governing equations. The beams are composed of three layers. The core is made from two constituents and varies across the thickness; however, the covering layers of the beams are made of bidirectional functionally graded material (BFGSW) and vary smoothly along the beam length and thickness directions. The power gradation model is considered to estimate the variation of material properties. The used formulation reflects the transverse shear effect and uses only three variables without including the correction factor used in the first shear deformation theory (FSDT) proposed by Timoshenko. The principle of virtual forces is used to obtain stability equations. Moreover, the impacts of the control of the power-law index, layer thickness ratio, length-to-depth ratio, and boundary conditions on buckling response are demonstrated. Our contribution in the present work is applying an analytical solution to investigate the stability behavior of bidirectional FG sandwich beams under various boundary conditions.

• Computers and Concrete
• /
• 제32권5호
• /
• pp.455-464
• /
• 2023

Seismologists now suggest that the earth has entered an active seismic period; many earthquake-related events are occurring globally. Consequently, numerous casualties, as well as economic losses due to earthquakes, have been reported in recent years. Primarily, significant and colossal damage occurs in reinforced concrete (RC) buildings with masonry infill wall systems, and the construction of these types of structures have increased worldwide. According to a report from the Ministry of Education in the Republic of Korea, many buildings were built with RC frames with masonry infill walls in the Republic of Korea during the 1980s. For years, most structures of this type have been school buildings, and since the Pohang earthquake in 2017, the government of the Republic of Korea has paid close attention to this social event and focused on damage from earthquakes. From a long-term research perspective, damage from structural collapse due to the short column effect has been a major concern, specifically because the RC frame with a masonry infill wall system is the typical form of structure for school buildings. Therefore, the short column effect has recently been a major topic for research. This study compares one RC frame with four different types of RC frames with masonry infill wall systems. Structural damage due to the short column effect is clearly analyzed, as the result of this research is giving in a higher infill wall system produces a greater shear force on the connecting point between the infill wall system and the column. The study is expected to be a useful reference for research on the short column effect in RC frames with masonry infill wall systems.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권6호
• /
• pp.18-28
• /
• 2015

이 연구의 목표는 학교 건물과 같은 저층 보-기둥 철근콘크리트 구조 건물에서 프리캐스트 벽패널을 사용한 새로운 내진보강 방법을 개발하는데 있다. 1개의 무 보강 보-기둥 실험체와 U형 PC 패널로 보강한 2개의 보강 보-기둥 실험체에 대한 정적 이력 하중실험을 진행하였다. 앵커 접합부 실험체는 전단 파괴될 것으로 해석되었고 철판 용접 접합부 실험체는 휨 파괴할 것으로 예측되었다. 실험체의 종국 내력은 상부 접합부의 전단 내력과 PC 패널 절곡 부 휨 위험단면에서 휨 내력 중 약한 것으로 결정되었다. 이 실험체에서, 한쪽 RC기둥이 가 하중(미는 실험 하중)을 받아 PC 패널 부재를 밀게 된다면, 다른 쪽 내부 수직부재는 상부 전단 접합부로부터 부 하중(당기는 실험 하중)을 받게 되어있었다. 가 하중을 받는 2개의 부재는 합성 휨 거동이 지배적이므로 합성단면의 휨 내력이 실험체의 최종 내력을 결정하게 되지만, 이 경우 최종 내력에 대하여 상부 전단 접합부 강도의 직접적인 영향은 없다고 볼 수 있다. 그러나 부 하중(당기는 하중)을 받는 RC 기둥과 PC 패널 부재는 비합성 거동이 지배적이고 실험체의 최종 내력은 상부 전단 접합부 전단내력의 크기에서 직접 영향을 받는 것으로 파악되었다. ACI 318M-11 Appendix-D 앵커 전단설계에 기초한 전단내력 그리고 실험에서 얻은 최대하중을 적용하여 마이다스 젠 탄성설계에 의하여 계산한 전단 외력에 대한 비교 해석결과는 실험결과와 일치하는 해석결과를 보여주었다.