• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.37-42
• /
• 2013

Tristructural-isotropic (TRISO)-coated particles were fabricated by a fluidized-bed chemical vapor deposition (FBCVD) method for use in a very high temperature gas-cooled reactor (VHTR). ZrC as a constituent layer of TRISO coating layers was deposited by a chloride process using $ZrCl_4$ and $CH_4$ source gases in a temperature range of $1400^{\circ}C$ and $1550^{\circ}C$. The change in the microstructure of ZrC depending on the deposition temperature and its effect on the hardness were evaluated. As the deposition temperature increased to $1500^{\circ}C$, the grain size of the ZrC increased and the hardness of the ZrC decreased according to the Hall-Petch relationship. However, at $1550^{\circ}C$, the ZrC layer was highly non-stoichiometric and carbon-rich and did not obey the Hall-Petch relationship in spite of the decrease of the grain size. A considerable amount of pyrolytic carbon at the grain boundaries of the ZrC as well as coarse granular pyrolytic carbon were locally distributed in the ZrC layer deposited at $1550^{\circ}C$. Therefore, the hardness decreased largely due to the formation of a large amount of pyrolytic carbon in the ZrC layer.

• 환경위생공학
• /
• 제15권4호
• /
• pp.98-104
• /
• 2000

Commercial rubber(IR, NR, BR), SBR, and tire were degraded by thermal degradation process. The oil yield of rubbers and tire ranges about 37~86%, it was increased with increase of operation temperature in pyrolysis. And the yield of pyrolytic oil was increased with increase of heating rate. The maximum oil yields of IR, NR, BR, SBR, and tire were 80, 73, 83, 86 and 55% each at $700^{\circ}C$ with a heating rate of $20^{\circ}C$/min, respectively. The pyrolytic oil components were consisted of about 50 aromatic compounds. The calorific value of purolytic oil of commercial rubber, SBR, and tire was measured by calorimeter, it was 39~40 kJ/g. The BET surface area of pyroblack was $47~63m^2/g$. The optimum condition of pyrolysis was operating temperature of $700^{\circ}C$ with heating rate of $20^{\circ}C$. Therefore, the pyrolytic oil and pyroblack are possible to alternative fuel and carbon black.

• 환경위생공학
• /
• 제11권1호
• /
• pp.57-61
• /
• 1996

This study was to decompose carbon tetrachloride and CFC with pyrolytic incineration unit because of prohibition of their usage sooner or later. We have investigated heating value and temperature versus decomposing rate, removal of $Cl_2$ and dust in the flue gas, The results obtained were as follows; 1. In combustion condition to decompose $CCl_4$ heating value was 3,300Kcal/Kg, retention time was 2,0 sec. incinerator exit temperature was $950^{\circ}C$. 2.The removal of HCI and $Cl_2$ in flue gas used NaOH as reagent, then molar ratio o of $Na^+/Cl^-$ was 1.07. 3. NaCI of dust component was more than 90 %, 2 stage venturi scrubber was used to remove dust, then removal rate of dust was 99% over at L/G of $1.7Vm^3$

• 항공우주기술
• /
• 제10권2호
• /
• pp.114-120
• /
• 2011

인공위성의 효율적인 열제어를 위해 알루미늄으로 만들어진 하니콤 패널과 OSR로 구성된 방열판을 사용한다. 또한 추가적으로 발열량이 많은 부품의 경우, 알루미늄으로 만들어진 더블러와 히트파이프 등을 이용하여 열제어를 수행한다. 최근 위성 전장 부품의 발열량의 증가로 정해진 위성의 크기, 발사 중량 및 비용으로 더 많은 열을 외부로 효율적으로 방출할 수 있는 방열 능력향상에 대한 필요성으로 새로운 열제어 물질에 대한 연구가 진행 중이다. 특히, 탄소 복합재는 일반적으로 열전도가 매우 높고, 가볍고, 기계적 강성에 좋은 특성이 있어 차세대 열제어를 위한 물질로 많은 연구가 진행되고 있다. 본 논문에서는 차세대 탄소 복합재인, APG(Annealed Pyrolytic Graphite)와 탄소-탄소 복합재(carbon-carbon composites)를 이용하여 통신패널의 열제어를 수행하는 경우와 기존의 열제어 방식과의 차이를 수치적으로 비교하였다.

• Korean Chemical Engineering Research
• /
• 제56권6호
• /
• pp.798-803
• /
• 2018

Si을 리튬이온전지 음극활물질로 사용하기 위해 입도를 $0.5{\mu}m$ 보다 작은 크기로 제어하였고 표면에 탄소를 약 10 nm 두께로 코팅하였다. 그 위에 탄소섬유를 50~150 wt% 양으로 성장시키고 다시 한 번 탄소코팅을 진행하였다. 이렇게 만들어진 Si 합성물질은 전기전도성을 높이기 위한 공정으로 이종 금속을 혼합하였으며 수명 특성을 개선하기 위해 흑연과 복합화하였다. 실험 변수에 따른 재료들의 물리화학적 특성을 XRD, SEM 및 TEM을 사용하여 측정하였고 코인셀을 제조하여 전기화학적 특성을 평가하였다. Si/PC (Pyrolytic Carbon)/CNF (Carbon Nano Fiber)보다 Si/PC/CNF/PC가 전체적으로 Si 함량이 줄어 방전용량은 상대적으로 낮게 나타났지만 전지평가에서 중요한 수명특성에서는 좋은 결과를 보여주었다. 0.2 C rate에서 $1512mA\;h\;g^{-1}$의 초기 방전 용량과 78%의 초기 효율을 나타내었고 10 싸이클에서 94%의 용량 보존율을 보여주었다.

• 한국세라믹학회지
• /
• 제45권9호
• /
• pp.561-566
• /
• 2008

Carbon fiber fabric-silicon carbide composites were fabricated by liquid silicon infiltration (LSI) process. The porous two-dimensional carbon fiber fabric performs were prepared by 13 plies of 2D-plain-weave fabric in a three laminating method, [0/90], [${\pm}45$], [$0/90/{\pm}45$] lay-up, respectively. Before laminating, a thin pyrolytic carbon (PyC) layer deposited on the surface of 2D-plain weave fabric sheets as interfacial layer with $C_3H_8$ and $N_2$ gas at $900^{\circ}C$. A densification of the preforms for $C_f-Si-SiC$ matrix composite was achieved according to the LSI process at $1650^{\circ}C$ for 30 min. in vacuum atmosphere. The bending strength of the each composite were measured and the microstructural consideration was performed by a FE-SEM.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2006년도 고분자리싸이클링 심포지엄
• /
• pp.15-32
• /
• 2006

Biomass had been attracted public attention as eco-friendly resource which not increases the greenhouse gas like carbon dioxide. In this study, it had been collected pyrolytic products such as bio-oil, char and pyrolytic gas from various biomass in a fluidized bed reactor which is one of the fast pyrolysis processes. To understand the characteristics of biomass pyrolysis, the variation of products yield and chemical composition was determined with various operating parameters like temperature, gas velocity($U_{0}/U_{mf}$) and bed height(L/D). In the optimum operating conditions, gas yield and water content was the lowest and concentration of guaiacols and syringols were the highest. The maximum yields of bio-oil was from 55% to 58% at $400^{\circ}C$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.914-917
• /
• 2002

Fabrication of micro carbon structures and patterns using laser-assisted chemical vapor deposition is studied. Argon ion laser and ethylene were used to grow micro carbon rod through pyrolytic decomposition of the reaction gas. The influence of reaction gas pressure and incident laser power on the diameter and growth rate of the micro carbon rod was experimentally investigated. The diameter of micro carbon rods increases linearly with respect to the laser power but is almost independent of the reaction gas pressure. Growth rate of the rod changes little with gas pressure when the laser power remains below 1W. When the carbon rod was grown at near threshold laser power, a very smooth surface is obtained on the rod. By continuously moving the focusing lens in the direction of growth, a micro carbon rod with a diameter of 28 ${\mu}{\textrm}{m}$ and aspect ratio of 100 was fabricated.

• 멤브레인
• /
• 제7권1호
• /
• pp.15-21
• /
• 1997

Carbon molecular sieve (CMS) membranes were synthesized by the pyrolysis of polymeric precursors. The CMS materials had oxygen-nitrogen selectivities much higher than those observed for the polymeric precursors. Typically molecular sieving materials have diffusion selectivities much higher than polymeric materials. This has been identified as a result of higher entropic selectivity of the molecular sieving materials. A study of the development of molecular sieving properties as the polymeric precursor is pyrolyzed into a CMS material will offer us an insight into polymeric molecular structures needed for enhanced entropic selectivity membrane materials.

• 한국세라믹학회지
• /
• 제44권3호
• /
• pp.169-174
• /
• 2007

TRISO coated fuel particle is one of the most important materials for hydrogen production using HTGR (high temperature gas cooled reactors). It is composed of three isotropic layers: inner pyrolytic carbon (IPyC), silicon carbide (SiC), outer pyrolytic carbon (OPyC) layers. In this study, TRISO coated fuel particle layers were deposited through CVD process in a horizontal hot wall deposition system. Also the computational simulations of input gas velocity, temperature profile and pressure in the reaction chamber were conducted with varying process variable (i.e temperature and input gas ratios). As deposition temperature increased, microstructure, chemical composition and growth behavior changed and deposition rate increased. The simulation showed that the change of reactant states affected growth rate at each position of the susceptor. The experimental results showed a close correlation with the simulation results.