• Nuclear Engineering and Technology
• /
• 제43권3호
• /
• pp.195-204
• /
• 2011

The effects on pool boiling heat transfer of aqueous solutions of boric acid ($H_3BO_3$) and sodium chloride (NaCl) as working fluids have been studied. Borated and NaCl water were prepared by dissolving 0.5~5% volume concentration of boric acid and NaCl in distilled-deionized water. The pool boiling tests were conducted using $1{\times}1\;cm^2$ flat heaters at 1 atm. The critical heat flux (CHF) dramatically increased compared to boiling pure water. At the end of boiling tests it was observed that particles of boric acid and NaCl had deposited and formed a coating on the heater surface. The CHF enhancement and surface modification during boiling tests were very similar to those obtained from boiling with nanofluids. Additional experiments were carried out to investigate the reliability of the additives deposition in pure water. The boric acid and NaCl coatings disappeared after repeated boiling tests on the same surface due to the soluble nature of the coatings, thus CHF enhancement no longer existed. These results demonstrate that not only insoluble nanoparticles but also soluble salts can be deposited during boiling process and the deposited layer is solely responsible for significant CHF enhancement.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권5호
• /
• pp.213-213
• /
• 2003

We investigated the monolayer behavior at the air-water interface with metal solution, the surface morphologies and the electrical properties such as conductivity, The calculated conductivity values of pure water subphase and its complexes with L $i^{+}$ ions are 5.6$\times$10$^{-l6}$ and 1.9$\times$10$^{-14}$ [S/cm], respectively. And the calculated barrier height D values of pure water subphase and its complexes with Li. ions are 0.70 and 0.66 [eV], respectively. We also attempted to fabricate a crown dendrimer Langmuir-Blodgett (LB) films containing functional end group that could form a complex structure with metal ions. Also, we investigated the surface activity of dendrimer films at air-water interface. In AFM images. the larger domains irregularly shaped structures on the top while the smaller ones were free from such defects. In conclusion, it is demonstrated that the metal ion around dendrimer and polymer included crown function group can contribute to make formation of network structure among crown function group and result in change of electrical properties.s.s.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권5호
• /
• pp.213-218
• /
• 2003

We investigated the monolayer behavior at the air-water interface with metal solution, the surface morphologies and the electrical properties such as conductivity, The calculated conductivity values of pure water subphase and its complexes with L $i^{+}$ ions are 5.6$\times$10$^{-l6}$ and 1.9$\times$10$^{-14}$ [S/cm], respectively. And the calculated barrier height D values of pure water subphase and its complexes with Li. ions are 0.70 and 0.66 [eV], respectively. We also attempted to fabricate a crown dendrimer Langmuir-Blodgett (LB) films containing functional end group that could form a complex structure with metal ions. Also, we investigated the surface activity of dendrimer films at air-water interface. In AFM images. the larger domains irregularly shaped structures on the top while the smaller ones were free from such defects. In conclusion, it is demonstrated that the metal ion around dendrimer and polymer included crown function group can contribute to make formation of network structure among crown function group and result in change of electrical properties.s.s.

• Geomechanics and Engineering
• /
• 제17권5호
• /
• pp.475-483
• /
• 2019

Vegetation cover plays a vital role in stabilizing the soil structure, thereby contributing to surface erosion control. Surface vegetation acts as a shelterbelt that controls the flow velocity and reduces the kinetic energy of the water near the soil surface, whereas vegetation roots reinforce the soil via the formation of root-particle interactions that reduce particle detachment. In this study, two vegetation-testing trials were conducted. The first trial was held on cool-season turfgrasses seeded in a biopolymer-treated site soil in an open greenhouse. At the end of the test, the most suitable grass type was suggested for the second vegetation test, which was conducted in an environmental control chamber. In the second test, biopolymers, namely, starch and xanthan gum hydrogels (pure starch, pure xanthan gum, and xanthan gum-starch mixtures), were tested as soil conditioners for improving the water-holding capacity and vegetation growth in sandy soils. The results support the possibility that biopolymer treatments may enhance the survival rate of vegetation under severe drought environments, which could be applicable for soil stabilization in arid and semiarid regions.

• Journal of Electrochemical Science and Technology
• /
• 제14권3호
• /
• pp.283-292
• /
• 2023

Currently, spray coating has attracted interest in the mass production of anode catalyst layers for proton exchange membrane water electrolysis (PEMWE). The solvent in the spray ink is a critical factor for the catalyst dispersion in ink, the microstructure of the catalyst layer, and the PEMWE performance. Herein, various pure organic solvents were examined as a substitute for conventional isopropanol-deionized water (IPA-DIW) mixture for ink solvent. Among the polar solvents that exhibited better IrO₂ dispersion over nonpolar solvents, 2-butanol (2-BuOH) was selected as a suitable candidate. The PEMWE single cells were fabricated using 2-BuOH at various ionomer contents, spray nozzle types, and drying temperatures, and their performance was compared to the cells fabricated using a conventional IPA-DIW mixture. The PEMWE single cells with 2-BuOH solvent showed good performances comparable to the conventional IPA-DIW mixture case and highly durable performances under accelerated degradation tests.

• 반도체디스플레이기술학회지
• /
• 제4권4호
• /
• pp.19-26
• /
• 2005

The process optimization of ozone concentration and half life time was investigated in ultra pure water and alkaline solutions for the wet cleaning of silicon wafer surface at room temperature. In the ultra pure water,. the maximum concentration (35 ppm) of ozone was measured at oxygen flow rate of 3 liters/min and ozone generator power over 60%. The half life time of ozone increased at lower power of ozone generator. Additive gases such as $N_2$ and $CO_2$ were added to increase the concentration and half life time of ozone. Although the maximum ozone concentration was higher with the addition of $N_2$ gas, a longer half life time was observed with the addition of $CO_2$. When $NH_4OH$ of 0.05 or 0.10 vol% was added in DI water, the pH of the solution was around 10. The addition of ozone resulted in the half life time less than 1 min. In order to maintain high pH and ozone concentration, ozone was continuously supplied in 0.05 vol% ammonia solutions. 3 ppm of ozone was dissolved in ammonia solutions. The static contact angle of silicon wafer surface became hydrophilic. The particle removal was possible alkaline ozone solutions. The organic contamination can be removed by ozonated ultra pure water and then alkaline solution containing ozone can remove the particles on silicon surface at room temperature.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1799-1807
• /
• 1994

Natural convection from a slightly inclined circular cylinders immersed in quiescent cold pure water was studied experimentally. The experiment was carried out for circular cylinders with uniform heat flux ranging from $100W/m^{2} to 800 W/m^{2}$ and inclined angle ranging from horizontal $({\phi}=0^{\circ}) to 15^{\circ}$. The flow fields around cylinder were visualized and heat transfer characteristics investigated by measuring the surface temperatures for each case. As the results, it is shown that flow patterns are changed consecutively through the sequence of steady state downflow, unsteady state flow and steady state upflow with increasing heat flux. At the same inclined angle, as heat flux increases, the average Nusselt number decreases and then increases. At the same heat flux, as inclined angle increases, the average Nusselt number decreases.

• 한국분무공학회지
• /
• 제19권1호
• /
• pp.15-18
• /
• 2014

In the present study, experiment on the evaporation of pure water droplet on heated surface was conducted, and the evaporative heat transfer coefficients were calculated from experimental results. The pure water droplet of about $10{\mu}l$ was applied onto the heat transfer surface, then the shape of the droplet was analyzed during the evaporation. In addition, the effect of surface roughness on the evaporative heat transfer was also investigated. Experimental results showed that the evaporative heat transfer coefficients increased rapidly along with the increase of surface temperature and the heat transfer coefficients increased with the increase of surface roughness.

• 대한기계학회논문집B
• /
• 제31권11호
• /
• pp.949-956
• /
• 2007

Pool boiling critical heat flux (CHF) of nanofluids with oxide nanoparticles of $TiO_2$ or $Al_2O_3$ was experimentally investigated under atmospheric pressure. The results showed that a dispersion of oxide nanoparticles significantly enhances the CHF over that of pure water. Moreover it was found that nanoparticles were seriously deposited on the heater surface during pool boiling of nanofluids. CHF of pure water on a nanoparticle-deposited surface, which is produced during the boiling of nanofluids, was not less than that of nanofluids. The result reveals that the CHF enhancement of nanofluids is absolutely attributed to modification of the heater surface by the nanoparticle deposition. Then, the nanoparticle-deposited surface was characterized with parameters closely related to pool boiling CHF, such as surface roughness, contact angle, and capillary wicking. Finally, reason of the CHF enhancement of nanofluids is discussed based on the changes of the parameters.

• 설비공학논문집
• /
• 제2권4호
• /
• pp.268-278
• /
• 1990

Hydrodynamic stability equations are formulated for natural convection flows adjacent to a heated or cooled, inclined, isothermal surface in pure water at $4^{\circ}C$, where the density variation with temperature becomes nonlinear. The resulting stability equations, when reduced to ordinary differential equations by a similarity transformation, constitute a two-point boundary-value problem, which was solved numerically. It is found from the obtained stability results that the neutral stability curves are systematically shifted to have lower critical Grashof numbers, as the inclination angle of upward-facing plate increases. Also, the nose of the neutral stability curve becomes blunter as the angle increases. It implies that the greater the inclination of the upward-facing plate, the more susceptible of the flow to instability for the wide range of disturbance wave number and frequency.