• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.356-361
• /
• 2005

In this paper, a new scheme of current programmed control for three phase PWM AC-AC converter is presented. Compared to duty-ratio voltage control, current programmed control has several advantages such as reduction of system order and inherent current protection. By considering only the magnitude components, the same scheme in the DC-DC converter can be extended to the three phase PWM AC-AC converter. Sensing the output voltage and the inductor current, an error signal will be generated by comparing the output voltage magnitude with a reference value. Then the error signal will be processed by a PI compensator to generate the current command. The converter switches will the change the state by a periodic clock pulse or at the instants when the inductor current magnitude reaches the current command. As an example case, the buck converter is treated. The converter analysis is carried out by applying the complex DQ circuit transformation to obtain basic physical insight into the converter operation and to establish some important characteristic equations for control purpose. The simulation with Simplorer shows the validity of the proposed scheme and the experimental results support the verification of the design.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권4호
• /
• pp.231-237
• /
• 2006

This paper proposes an effective drive of high intensity discharge (HID) lamp ballast for cars. All control functions of the proposed ballast are implemented using a low-cost single chip microcontroller, PIC16C73 to optimize the total system size and to minimize cost through minimization of total component number. The proposed ballast generates high open-circuit voltage to ignite the lamp and is controlled to supply effectively the power required to shorten warm-up period after the breakdown. The DC-DC converter of the DC-AC converter part of the ballast utilizes the flyback converter topology that can minimize component number. Also, because to more minimize the ballast size, the transformer size must be minimized, for this, PWM (Pulse Width Modulation) pulses are generated with high frequency using the PWM module of the microcontroller. An analysis for this is explained, briefly. As if the operation of the lamp and ballast arrives at steady-state, then the ballast must AC-control the lamp, for this, the microcontroller utilizes the other PWM module. And the part related to the igniter is explained, briefly. It is shown through experimental results that the controller of the proposed ballast has good performance for the HID lamp for cars.

• 대한치과의사협회지
• /
• 제49권11호
• /
• pp.660-669
• /
• 2011

Er: YAG laser irradiation utilizing the newly developed RCLase side-firing spiral tip was used for the cleansing of root canals following their bio-mechanical preparation with ProTaper Ni-Ti files. The distal and palatal roots of 20 freshly extracted molar teeth were instrumented to size F3 with ProTaper files. In the experimental group (10 teeth) the pulp chamber and the root canals were filled with EDTA 17% and the root canals were lased for 30 s using the Er: YAG laser irradiation at 600 mJ per pulse and a frequency of 12 Hz. In the control group (10 teeth) the root canals were not lased. Scanning electron microscope analysis showed clean wall surfaces of the lased root canals with open dentinal tubules, free of smear layer and debris. In the scanning electron microscope photographs of the walls of the non-lased root canals a considerable amount of debris could be detected. It appears that an efficient cleansing of the root canal system can be achieved by using the Er: YAG laser irradiation with the RCLase Side-firing Spiral Tip following bio-mechanical preparation of the root canal with Ni-Ti Taper files.

• 한국전기전자재료학회논문지
• /
• 제24권1호
• /
• pp.36-41
• /
• 2011

Medical X-ray has been brought many changes according to the rapid development of high technology. Especially, for high-voltage generator which is the most important in X-ray generation the traditional way is to use high-voltage electric transformers primarily. However, since it is large and heavy and the ripple rate of DC high-voltage applied to X-ray tube is too big, it has a disadvantage of low X-ray production efficiency. To solve these problems, the studies about high-voltage power supply are now proceeding. At present, the high-voltage generator that generates high-voltage by making high frequency using inverter control circuit consisting of semiconductor device is mainly used. High-voltage generator using inverter has advantages in the diagnosis using X-ray including high performance with short-term use, miniaturization of power supply and ripple reduction. In this study, the X-ray high-voltage device with inverter type using pulse width modulation scheme to the control of tube voltage and tube current was designed and produced. For performance evaluation of produced device, the control signal analysis, irradiation dose change and beam quality depending on the load variation of tube voltage and tube current were evaluated.

• 대한전자공학회논문지TC
• /
• 제47권7호
• /
• pp.18-22
• /
• 2010

본 논문에서는 실내 환경에서 초광대역 무선통신을 이용한 양방향 위치인식 기법의 성능을 분석하였다. 실험 환경은 IEEE802.15.3a 채널을 사용하였고, 위치인식 기법으로 TOA를 적용하여 분석하였다. 초광대역 무선통신 기술은 낮은 송신 전력으로 기존 시스템에 간섭의 영향이 적고, 주파수 공유가 가능하므로 주파수 효율을 높일 수 있다. 그리고 매우 좁은 폭을 갖는 펄스를 사용하기 때문에 위치인식의 정밀도가 높다. 비동기 TWR 프로토콜을 이용한 TOA방식은 단말과 기지국뿐만 아니라 기지국들 간에도 동기화를 수행하지 않아도 되는 장점이 있다. 모의실험을 통하여 초광대역 무선통신을 이용한 위치인식 기법의 실내 채널 영향에 대한 오류 확률 및 위치인식 성능에 대해 분석하였고 제안된 기법의 유용성을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.19-23
• /
• 1996

Deburring and edge finishing technology as the last process of machining operation is required for manufacturing of advanced procesion components, duburring has treated as a difficult problem on going tothe highefficency, automation in the FMS. Removal of butt with various shapes, dimensions and properties coultn't has a standard and has depended on manual treatment. Especially, deburring for cross hole inside owing to passing through out perpendicular to a main hole is more difficult, the electrolytic method is proper as its solution at practical aspects. Therefore, for the high effciency and automation of intermal deburring in the cross hole, development of electrolytic debutting technology is needed. So, the new process in the burr treatment is supposed. In this study, in the eliminating burr inside cross hole, the principle and machining performances of electrochemical deburring by Cubic-Boron-Nitrade abrasive electroplate wheel are investigated, Design and manufacture of CBN electroplated wheel and analysis of characteristics with electrolytic debutting are achieved. Also deburring efficiency and electrolytic performance for cross hole were examined according to electrolytic current and electrolytic deburring condition corresponding to acquired edge quality was found out.

• 자동차안전학회지
• /
• 제6권2호
• /
• pp.49-54
• /
• 2014

Development in vehicle industry could increase interest in children's safety recently. However the research of children safety is not being conducted as many as that of adult's. Especially the basic study for the vehicle crash on-board children was not much. This study focused on the effect of seatbelt anchorage points to evaluate children's safety in frontal crash. The current regulation of the seatbelt anchorage points is suitable for ranged from female 5% to male 95%. The assessment of children's safety at buckle up of no used CRS(child restraint system) was performed using frontal sled tests. The frontal crash pulse in sled tests was designed to the average of about 30 KNCAP frontal crash pulses. To reduce number of experiments, DOE is used. The Q6 child dummy and standard seat in UN R 129 were used. According to the analysis of test results, children's safety has been influenced by the points of seatbelt anchorage.

• Journal of Power Electronics
• /
• 제12권3호
• /
• pp.377-386
• /
• 2012

An interleaved bridgeless buck-boost AC/DC converter is presented in this paper to achieve the characteristics of low conduction loss, a high power factor and low harmonic and ripple currents. There are only two power semiconductors in the line current path instead of the three power semiconductors in a conventional boost AC/DC converter. A buck-boost converter operated in the boundary conduction mode (BCM) is adopted to control the active switches to achieve the following characteristics: no diode reverse recovery problem, zero current switching (ZCS) turn-off of the rectifier diodes, ZCS turn-on of the power switches, and a low DC bus voltage to reduce the voltage stress of the MOSFETs in the second DC/DC converter. Interleaved pulse-width modulation (PWM) is used to control the switches such that the input and output ripple currents are reduced such that the output capacitance can be reduced. The voltage doubler topology is adopted to double the output voltage in order to extend the useable energy of the capacitor when the line voltage is off. The circuit configuration, principle operation, system analysis, and a design example are discussed and presented in detail. Finally, experiments on a 500W prototype are provided to demonstrate the performance of the proposed converter.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.12-18
• /
• 2004

Transient natures of diesel sprays are often characterized with spray visualization, since it is a non-intrusive and straightforward technique to be applied. However, as injection pressure is increased higher than a thousand bar in a modern direct injection diesel engine, very fine temporal and spatial resolutions in the spray visualization are required while sprays become optically denser. Discussed in this paper are macroscopic and microscopic spray visualization techniques and an example of image processing process for efficient and consistent measurement of spray parameters. The injection rate measurement method based on hydraulic pulse principle was suggested as a way of estimating injection velocity for transient diesel sprays. The spray visualization and injection rate measurement techniques were applied to analyze transient diesel sprays from a common-rail injection system and found to be practically effective.

• 한국전자파학회논문지
• /
• 제8권6호
• /
• pp.645-655
• /
• 1997

본 논문에서는 CDMA 시스댐에 적용하기 위해 기저 대역에서 설계된 비동기식 동기 추적 회로의 성능을 이론적으로 분석하고 컴퓨터 시뮬레이션을 통해 검증한다. AWGN 채널 환경에서 지터 분산을 펼스 성형 필터, 타이밍 오프셋, 신호 대 잡음 비, 루우프 필터 계수의 함수로 이론적으로 유도하고 2차 동기 추적 회로를 중심으로 루우프 필터의 설계에 판해 고찰한다. 끝으로, 설계된 동기 추적 회로를 ETRI에서 IMT-2000을 위해 설계한 동기식 CDMA 시스템의 역방향 링크에 적용하여 AWGN과 레일라이 페이딩 환경에서의 성능을 시율레이션을 통해 검증한다.