• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.5
• /
• pp.700-705
• /
• 2012

$Prunus$ $mume$ was steamed for easier removal of the pulp. The steamed fruit pulp was vacuum dried and powdered. The steamed $Prunus$ $mume$ powder (SPP) was passed through a 250 ${\mu}m$ sieve, fluidized in a fluid-bed granulator, and then granulated by top-spraying with water (SPPGW) or the extract obtained from steam (SPPGE). Then the physicochemical and sensory properties of SPP, SPPGW, and SPPGE were evaluated. The flowability of powder (angle of repose $^{\circ}$) of SPP, SPPGW and SPPGE was $23.59^{\circ}$, $11.07^{\circ}$, and $13.94^{\circ}$, respectively. The water dispersibility of SPP, SPPGW, and SPPGE was 18.69, 10.04 and 6.00 sec, respectively. Also, the overall acceptance of SPP, SPPGW and SPPGE was 3.00, 3.44 and 6.56, respectively. In conclusion, SPPGE can be used as granular steamed whole fruit pulp with good powder flowability and dispersibility, and therefore consumer acceptance.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.61-67
• /
• 2015

As the production of palm oil has been increased, the generation of oil palm biomass is also increased and the utilization of the oil palm biomass become more significant topic. One third of the oil palm biomass is empty fruit bunch (EFB) and the other two thirds are oil palm trunks and fronds. However, the effective use of oil palm biomass has not been developed and most of it is discarded near oil palm plants. In this study, we investigated the applicability of EFB to the paperboard mills, as an organic filler. The new organic filler was manufactured in a laboratory by grinding and fractionating dried EFB powder, and its properties were analyzed. The particles of EFB organic filler were larger and more spherical than those of the commercial wood powder. The use of EFB organic filler resulted in a higher bulk of the handsheets with similar trends of physical strength, compared to those made with wood powder. It was concluded that EFB could be used as a raw material to manufacture organic filler for paperboard production.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.4 s.107
• /
• pp.60-66
• /
• 2004

In this paper, oyster shell, diatomaceous earth, and active carbon were used as filter media for treating wastewater produced in paper mills. After filtering, the changes of COD and turbidity were investigated. As the results of estimating the efficiency of wasterwater treatment, porous oyster shell having higher specific surface area in powder was more effective than the others in removal of contaminants in waterwater, especially turbidity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.3
• /
• pp.53-58
• /
• 2008

Wood composite, could generally be made from very fine wood powder(<150 mesh) because more large size of wood particle had much less plasticity compared of polymer. To make more high plasticity of relatively large size of wood particle, wood particles were chemically modified with some reagent for acetylation and esterification, etc. WPC(wood plastic composite) was prepared with chemically modified wood particles and the mechanical properties of WPC were evaluated. WPC of esterified wood with maleic anhydride shows the highest level in tensile strength and breaking elongation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.2
• /
• pp.24-32
• /
• 2004

Toner used in xerographic printing process is hydrophobic powder with low surface energy. The toner ink film fused on paper surface can be efficiently detached from a fiber surface during pulping, but it does not fragment again into fine toner particles. Ink agglomerates that result have too large particle size to be deinked by flotation. The purpose of this study is to enhance toner agglomeration using 1-octadecanol for improving the toner removal by screening. The effect of pH, pulping temperature, and 1-octadecanol on toner agglomeration and removal by screening was investigated using image analysis methods. Results showed that the size of toner agglomerates increased substantially when pulping was carried out at high temperature under acidic condition. When toner agglomerates showed spherical shape, the particle removal efficiency of screening was improved.

• Journal of Powder Materials
• /
• v.25 no.3
• /
• pp.232-239
• /
• 2018

In this paper, the recovery and nanoparticle synthesis of Ag from low temperature co-fired ceramic (LTCC) by-products are studied. The effect of reaction behavior on Ag leaching conditions from the LTCC by-products is confirmed. The optimum leaching conditions are determined to be: 5 M $HNO_3$, a reaction temperature of $75^{\circ}C$, and a pulp density of 50 g/L at 60 min. For the selective recovery of Ag, the [Cl]/[Ag] equivalence ratio experiment is performed using added HCl; most of the Ag (more than 99%) is recovered. The XRD and MP-AES results confirm that the powder is AgCl and that impurities are at less than 1%. Ag nanoparticles are synthesized using a chemical reduction process for recycling, $NaBH_4$ and PVP are used as reducing agents and dispersion stabilizers. UV-vis and FE-SEM results show that AgCl powder is precipitated and that Ag nanoparticles are synthesized. Ag nanoparticles of 100% Ag are obtained under the chemical reaction conditions.

• Clean Technology
• /
• v.29 no.2
• /
• pp.87-94
• /
• 2023

The recovery of valuable metals from waste lithium-based secondary batteries is very important in terms of efficiently utilizing earth's limited number of resources. Currently, the cathode material of a LiFePO₄ battery, a type of battery which is widely used in automobiles, contains approximately 5% lithium. After use, the lithium in these batteries can be used again as a raw material for new batteries through lithium recycling. In this study, low-concentration sulfuric acid, a commonly used type of inorganic acid, was used to selectively leach the lithium contained in a waste LiFePO₄ cathode material powder. In addition, in order to compare and analyze the leaching efficiency and separation efficiency of each component, the optimalleaching conditions were derived by applying a two-step leaching process with pulp density being used as a variable during leaching. When leaching with pulp density as a variable, it was confirmed that at a pulp density of 200 g/L, the separation efficiency was approximately 200 times higher than at other pulp densities because the iron and phosphorus components were hardly leached at this pulp density. Accordingly, the pulp density of 200 g/L was used tooptimize the leaching conditions for the selective leaching and recovery of lithium.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.1-6
• /
• 2009

The purpose of this study was to investigate effects of lignocellulosic fillers made of wood powder and inorganic fillers, such as GCC and PCC, on physical properties of papers. Mechanical treatment and chemical treatment were carried out subsequently for generating lignocellulosic fillers, and then inorganic filler and wood powder were mixed together, and then mechanically treated for making lignocellulosic fillers covered with inorganic fillers. Consequently the particle size of lignocellulosic fillers was higher than that of inorganic fillers, which led to lumen loading and simultaneously surface coverage of fine inorganic fillers. Lignocellulosic fillers contributed to the increase of both bulk and opacity of handsheets dramatically, but some of properties including tensile strength, brightness and roughness decreased compared to inorganic fillers.

• Textile Coloration and Finishing
• /
• v.27 no.2
• /
• pp.149-154
• /
• 2015

To investigate the biodegradation of the cellulose powder(CP) derived from Styela clava tunics(SCT), some physico-chemical properties and biodegradability of SCT-CP were measured after the incubation for 45 days. The particles size of SCT-CP prepared with washing, bleaching, drying, and grinding processes was $150-400{\mu}m$ although most of particles (70%) was more than $400{\mu}m$. The cellulose structures of SCT-CP detected using the X-ray diffraction and DSC analysis was very similar with that of wood pulp powder(WP-CP). The glass transition temperature was not detected in both samples. Furthermore, more than 90% of the SCT-CP was degraded, whereas only over 70% of the WP-CP was degraded after the incubation for 45 days. Therefore, these results suggest the possibility that SCT-CP is particularly applicable to prepare medical fiber and film for disease treatment.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.2
• /
• pp.33-40
• /
• 2013

Powdered additive or organic filler is used to improve paperboard thickness and to reduce drying energy consumption in the Korean paperboard industry. In a previous study, we identified alternative non-lignocellulosic resources to wood powder, specifically brewers grain and oil palm frond powders, and verified that these materials had the same functionality as wood powder. The main drawback of the use of such additives, including both lignocellulosic and non-lignocellulosic resources, is the deterioration in paperboard strengths. Therefore, we carried out a basic study on the surface modification of brewers grain and oil palm frond powders to improve the strengths of paperboard. Surface modification was performed using various types of cationic and oxidized starches. The streaming current and zeta-potential of the two non-lignocellulosic powders were measured and CLSM images were taken to assess the surface modification.