• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.513-520
• /
• 2002

A 5-row walking garlic harvester with pulling mechanism was developed in the study, based upon a kinematical analysis and related preliminary field tests on the conventional garlic harvesting method. The harvesting efficiency of the developed harvester was more than 98% in the garlic field irrigated before harvesting, 80-85% in the field without irrigation. The harvesting performance of the harvester was 660∼825㎡/hr at the forward speed of harvester of 0.3m/s in the irrigated field before garlic harvesting. For proper garlic drying and collection, the harvester discharged the harvested garlic on the ground uniformly at the angles of 135。∼150。 to its forward direction with the garlic bulb's placing toward the harvester. In the field tests, it was recommended that the forward speed of the harvester be approximately less than 0.2m/s, and that the spacing of planting garlic seeds should be standardized in the future fur increasing its harvesting efficiency.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.2
• /
• pp.39-43
• /
• 2012

This paper presents a study on the design of a pulling module for silicon ingot and an apparatus of manufacturing silicon single crystal ingot using the same method. The pulling module is conceptually designed by using TRIZ. Czochralski method(CZ) is representative way to manufacture single crystal ingot for wafers. The seed can be broken by high tension which is caused by large weight of a silicon ingot. The solution of this problem has been derived using 6SC(6 steps creativity)TRIZ. The pulling module is actuated by DC motor and rollers. High tension in the seed is removed by the rotate-elevate motion of rollers in the pulling module. A rubber belt is included in the rotate-elevate mechanism for increasing friction between rollers and silicon ingot.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1211-1214
• /
• 2004

High-heeled women have been identified with balance control problems. The purposes of this study were to objectively quantify the displacements and velocities of center-of-pressure (COP) of body during waist pulling and to compare the differences between barefooted and high-heeled situations. We used a waist pulling system which has three different magnitudes to sway the subjects. We found that the kinematic information of barefooted and high-heeled women's COP is very important in understanding the mechanism of postural balance control of women in every-day life. In the high-heeled's case, the displacement of COP increases in 200％ as against bare footed. Also the velocity variation of COP grows three times than the bare footed. COP analysis in postural balance study of high-heeled women is also considered useful in development of the safety systems that prevent high-heeled women from falling

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1160-1165
• /
• 2004

The purpose of this study was to calculate three dimensional angular displacements, moments and joint reaction forces of the ankle joint during the waist pulling, and to assess the ankle joint reaction forces according to different perturbation modes and different levels of perturbation magnitude. Ankle joint model was assumed 3-D ball and socket joint which is capable of three rotational movements. We used 6 cameras, force plate and waist pulling system. Two different waist pulling systems were adopted for forward sway with three magnitudes each. From motion data and ground reaction forces, we could calculate 3-D angular displacements, moments and joint reaction forces during the recovery of postural balance control. From the experiment using falling mass perturbation, joint moments were larger than those from the experiment using air cylinder pulling system with milder perturbation. However, JRF were similar nevertheless the difference in joint moment. From this finding, we could conjecture that the human body employs different strategies to protect joints by decreasing joint reaction forces, like using the joint movement of flexion or extension or compensating joint reaction force with surrounding soft tissues. Therefore, biomechanical analysis of human ankle joint presented in this study is considered useful for understanding balance control and ankle injury mechanism.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.698-705
• /
• 2005

This study contains actual scaled site experiments on mediation factors affecting ultimate pulling force of the buoyancy resisting anchor which is installed underground water level suffering buoyancy force and breaking mechanism. Site buoyancy test selected the buoyancy acting site where acting buoyancy to the station structure since the stream and reservoir is neighboured to the vicinity ground and executed site experiments leading to variation of anchoring length, drilling diameter and tendon diameter at the weathered rock ground. The test result showed that pulling force getting increased more and more proportionate to increase of anchoring length, drilling diameter and tendon diameter, and as a result of analysis for correlations between anchoring length-ultimate limited load and drilling diameter-ultimate load (on the basis of 254mm settlement), modulus of correlation showed very high relation 0.9 and 0.99 respectively and correlation formular showed the limited load is increasing proportionate to cubic meters of anchoring length as well as the ultimate load proportionate to alignment of drilling diameter. It is also showed that limited load increased about 42.5% from 392kN to 559kN as a result of change the tendon diameter to 36mm and 50mm.

• The Journal of Korea Robotics Society
• /
• v.3 no.4
• /
• pp.315-322
• /
• 2008

A new soft finger mechanism using a spring as a backbone is proposed in this work. It is a 4 DOF mechanism that consists of a spring and 3 cylinders, which behave like joints with 3 up-and-down rotations and 1 left-and-right rotation. To control each joint, cylinders have small holes in their cross-sectional areas, and wires of different length are penetrated into these holes. We can control each joint by pulling the corresponding wire. The forward kinematics is solved by using the geometry of mechanism. And the relationship (Jacobian) between the linear velocity of the wires and the joint angular rate is obtained. A virtual simulator is developed to test the validity of the kinematic model. In the experiment, first, the position control is conducted by tracking a given trajectory. Second, to verify the flexibility and safety, we show that the soft finger deflects in a safe manner, in spite of the collision with environment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1328-1331
• /
• 2003

As rates of gastric cancer. fatness. and GERD (chronic gastric esophageal reflux disease) patients have been increased in the world, suturing mechanism using endoscope has been focused. which is the medical instrument to apply stitches and suturing inside the body, since it helps the patients lessen pains and reduce operation time. This paper deals with mechanism design, which makes it possible to apply multiple suturing without the repeat of inserting and removing the endoscope. This successive suture mechanism includes gripper, linkage, rotational part, and articulation part. Also, the mechanism is operated through 4mm one-side channel attached to the endoscope by means of pulling wires.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.57-62
• /
• 2000

An experimental study has been performed to investigate friction characteristics of pre-coated metals widely used in domestic appliances. Seven-coated sheet metals are tested by using three friction mechanism such as straight pulling, frictionless roller, and non-rotational roller with three kinds of cylindrical rollers. In this experiment, effects of friction mechanism, blank thickness, and roller diameter on friction coefficient, surface roughness, and scoring factor have been investigated From the experimental results, it has been found that tested pre-coated sheet metals have low friction coefficients ($\mu$ = 0.15~0.20) because films coated on sheets take a role of lubricants. Friction coefficients of pre-coated metals decrease with increasing roller-diameters. Surface of pre-coated metals can be improved by decreasing the blank thickness

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.399-421
• /
• 1996

(1) The solute distribution mechanism was analyzed for the Si0.95Ge0.05 single crystal fiber by u-PD method. (2) The steady-state solutions were obtained for the molten zone and the capillary zone. (3) The effect of the convection in the molten zone on partitioning was not significant for many cases. (4) Intermediate transient rise of Ge was shown by the sudden change of the growth velocity or molten zone height. (5) Periodic compositional modulation can be designed by using the intermediate transient.

• Journal of Computing Science and Engineering
• /
• v.10 no.1
• /
• pp.32-38
• /
• 2016

Navigating a large 3D virtual environment using a generic haptic device can be challenging since the haptic device is usually bounded by its own physical workspace. On the other hand, mouse interaction easily handles the situation with a clutching mechanism-simply lifting the mouse and repositioning its location in the physical space. Since the haptic device is used for both input and output at the same time, in many cases, its freedom needs to be limited in order to accommodate such a situation. In this paper, we propose a new mechanism called Z-Clutching for 3D navigation of a virtual environment by using only the haptic device without any interruption or sacrifice in the given degrees of freedom of the device's handle. We define the clutching state which is set by pulling the haptic handle back into space. It acts similarly to lifting the mouse off the desk. In this way, the user naturally feels the haptic feedback based on the depth (z-direction), while manipulating the haptic device and moving the view as desired. We conducted a user study to evaluate the proposed interaction technique, and the results are promising in terms of the usefulness of the proposed mechanism.