• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.965-970
• /
• 2002

The strengthening of concrete structures in situ with externally bonded carbon fiber is increasingly being used for repair and rehabilitation of existing structures. Carbon fiber is attractive for this application due to its good tensile strength, resistances to corrosion, and low weight. Generally bond strength and behavior between concrete and carbon fiber mesh(CFM) is very important, because of the enhanced bond of CFM. Therefore if bond strength is sufficient, it will be expected to enhance reinforcement effect. If insufficient, reinforcement effect can not be enhanced because of bond failure between concrete and CFM. This study is to investigate the bond strength of CFM to the concrete using direct pull-out test and tensile-shear test. The key variables of the experiment are the location of clip, number of clips and thickness of cover mortar. The general results indicate that the clip anchorage technique for increasing bond strength with CFM appear to be effective to maintain the good post-failure behavior.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.8
• /
• pp.1062-1066
• /
• 2001

Studies were carried out on forty young bulls of the Hariana breed (around 18 months of age) selected on the basis of their dam's milk yield at the animal farm of CCS HAU, Hisar during the period 1993-1999. Since animals showed variation in capacity to work over prolonged periods, they were subjected to regimes of carting without load and with 8 qtls. of load for three hours. The study revealed that maximum change took place in the pulse rate, followed by respiration rate and rectal temperature. The mean fatigue score for pulling an empty cart ranged between 1.66 to 2.20 after two hours work, and 2.36 to 2.73 after three hours work. For a cart loaded with 8 qtls., the corresponding ranges were 2.90 to 3.36 and 3.40 to 4.10, respectively. These results indicated that the animals under experiment had the capacity to pull moderate load (8 qtls.) for about two hours without showing any serious effect on the ability to recover and soon to work again.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.2
• /
• pp.45-51
• /
• 2009

Three-dimensional numerical analyses of mechanical ventilation system in vent shaft of subway in operation are carried out in relation with the different air flow passage of vent shaft and two ventilation operation modes of push/pull, The ventilation characteristics of vent shaft with regard to the shape change are evaluated. And the air flow rate through the vent shaft by ventilation system is measured within subway in operation to assess the accuracy and applicability of the numerical analysis method. The decrease of air flow rate due to vent-shaft change are between 0.7 to 2.2% in the cases examined.

• Journal of the Korean Home Economics Association
• /
• v.20 no.1
• /
• pp.1-10
• /
• 1982

This experiment was made on the basis of the general observation that silk fabrics is flaccid in sun light. The purpose of this test is to examine efficiency between the processed thread and the unprocessed one after putting the later under the xenon-lit system, which produces continuous spectrum of bright white beam similar to sun light. (i) Color division of silk thread : white, yellow blue (ii) light division and irradiation time : sun lightlongrightarrow210 hrs, Xenonlongrightarrow50,100, 150 hrs. Under the above conditions each object was be tested with and extensometer, TENSILON Type III for the results of (a) the weight-expansibility curve of the silk thread (b) the relationship between cutting in tensity and maximum, weight (c) maximum expansion rate (d) the expansion energy of the tested silk thread (e) the beginning pull-stretch resistance rate of the tested silk thread (f) color difference after processing The results are illustrated in the appropriate tables and figures. Consequently the generalobservation that silk fabrics is flaccid is relevant only in terms of color. So for as Cutting-intensaty is concerned, it turned out to be less flaccid than in color. On the contrary when the untested silk thread was conpared with the xenon-irradiated ones, the latter proved itself to be more flaccid in cutting expansibility than the former. We have learned through this experiment that, after the all rounds of this test, the color tone and chroma of the colored materials remained without significant change, where as their color value changed to a large extent.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.1
• /
• pp.58-64
• /
• 2003

A mechanical press joining was investigated in ender for joining A1-5052 sheets for automobile body weight reduction. Static tensile and fatigue tests were conducted using tensile-shear specimens for evaluation of fatigue strength of the joint. During Tox joining process for A1-5052 plates, using the current sheet thickness and punch diameter, the optimal applied punching force was found to be 32 kN under the current joining condition. For the static tensile-shear experiment results, the fracture mode is classified into interface fracture mode, in which the neck area fractured due to influence of neck thickness, and pull-out fracture mode due to influence of plastic deformation of the joining area. And, during fatigue tests for the A1-5052 tensile shear specimens, interface failure mode occurred in the region of low cycle. The fatigue endurance limit approached to 6 percents of the maximum applied load, considering fatigue lifetime of $2.5\times10^6$ cycles.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.1-6
• /
• 2015

Self-piercing riveting (SPR) is receiving more recognition as a possible and effective solution for joining automotive body panels and structures, particularly for aluminum parts and dissimilar parts. In this study, static strength and fatigue tests were conducted using coach-peel and cross-tension specimens with Al-5052 plates for evaluation of fatigue strength of the SPR joints. For the static experiment results, the fracture modes are classified into pull-out fracture due to influence of plastic deformation of joining area. During the fatigue tests for the coach-peel and cross-tension specimens with Al-5052, interface failure mode occurred on the top substrate close to the rivet head in the most cycle region. There were relationship between applied load amplitude $P_{amp}$ and life time of cycle N, $P_{amp}=715.5{\times}N^{-0.166}$ and $P_{amp}=1967.3{\times}N^{-0.162}$ were for the coach-peel and cross- tension specimens, respectively. The finite element analysis results for specimens were adopted for the parameters of fatigue lifetime prediction. The relation between SWT fatigue parameter and number of cycles was found to be $SWT=192.8N_f^{-0.44}$.

• Journal of Biosystems Engineering
• /
• v.17 no.3
• /
• pp.237-246
• /
• 1992

This study was conducted to investigate experimentally the effect of track tension on the tractive performance of rice combine. The experiment was carried out at the two in-door soil bins with soil types of loam and sandy loam. The initial track tension was varied by three different values of 0.71, 1.75 and 3.84kN at three different forward velocity settings of 0.17, 0.32 and 0.45m/s, respectively. The data acquisition system was designed and used for the measurement of pull, driving axle torque and its velocity under the test conditions to calculate the tractive efficiency. Results of the study were summarized as follows : 1) The effect of the initial track tension on the tractive efficiency was found being significantly dependent on soil types but not on forward velocities. Therefore, the benifit of adjusting the initial track tension may be obtained when the types of soils on which combines operate are changed. 2) In loam, tractive efficiency decreased with increase in track tension. However, it increased in sandy loam until it reached to a peak value and then decreased with increase in track tension. 3) The maximum tractive efficiency of the tested combine was obtained with an initial track tension of about 1.75kN on sandy loam, and below that on loam at about 5% slippage without being noticeably influenced by the forward velocity.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.219-223
• /
• 2009

This paper is the result of investigation of ONO PPSM(ONO PORTABLE SLIP METER) by way of experiment to see the validity as a slip meter, ONO PPSM is a portable slip meter which was made up for the weak points of O-Y PSM(ONO-YOSHIOKA PULL SLIP METER) which takes an accurate measurement of the slip resistance but very heavy and hard to operate. In order to know the stability of the measurement result of ONO PPSM, we measured the slip resistance against 4 different kind of floor materials. As a result of this, we found out that the coefficient of variability of CSR' is less than 0.05. Also, we verified the relation between CSR' and CSR. more specifically by doing the slip test against 7 different kinds of inorganic matter floor materials. We increased the usability of ONO PPSM as a slip meter by suggesting the method of sharing the evaluation index of slip of CSR' and C.S.R.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1275-1284
• /
• 2018

The coaxial magnetic gear with the flux concentrating structure is known that it has the torque performance advantage over the coaxial magnetic gear having surface mounted permanent magnet, thanks to the flux focusing effect. But, if the solid cores are used in the modulating pieces and rotor cores to consider the mechanical reliability and cost reduction, the operating torque of the flux concentrating coaxial magnetic gear can be significantly diminished because the iron losses at the solid cores affect the actual transmitted torque. Furthermore, the modulating pieces and rotor cores have different characteristics of the iron losses from one another, because the space harmonic components of the magnetic flux density, which cause the iron losses, are different. Thus, in this paper, we focused on the analysis of the characteristics of the space harmonic components of the magnetic flux density and resultant eddy current losses in the surface mounted PM and flux concentrating coaxial magnetic gears, when these coaxial magnetic gears have the solid cores at the modulating pieces and rotor cores. The characteristics of pull-out torque (static torque), operating torque (dynamic torque), and efficiency are also researched, and compared by the 3D finite element analysis (FEA) and experiment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.169-176
• /
• 2021

In this study, pull-out tests were conducted at room temperature, 150 ℃ and 250 ℃ to evaluate the residual bond strength of carbon fiber reinforcement polymer, CFRP after elevated temperature and deformed steel rebar of D10 and D13 were also evaluated after the high temperature heating for comparison. As a result of the experiment, the bond strength of the CFRP after 150 ℃ and 250 ℃ decreased by 9.94 % and 41 %, respectively. On the other hand, after thermal heating, both the steel rebar of D10 and D13 had a lower rate of reduction in bond strength than that of the CFRP. Also slip at the maximum bond strength also decreased after the heating for both the CFRP and the rebars. Through it, the correlation between the bond strength and the slip reduction due to thermal heating was confirmed and bond slip models were presented. Finally the experimental result was evaluated as relative bond strength to identify the residual bond performance of the CFRP and the rebar after the heating was confirmed by comparing with the existing test result of the bond strength after elevated temperature.