Journal of the Korea institute for structural maintenance and inspection (한국구조물진단유지관리공학회 논문집)

Korea Institute for Structural Maintenance Inspection (한국구조물진단유지관리공학회)
권호 표지
DOI QR코드

DOI QR Code

Evaluation of Residual Bond Stress between Carbon-fiber Reinforced Polymer and Steel Rebar Using Ultra-High-Performance-Concrete after Elevated Temperature

초고강도 콘크리트를 활용한 고온가열 이후의 탄소 보강근과 철근의 잔류 부착성능 평가

  • 유선재 (고려대학교, 건축사회환경공학부) ;
  • 이호진 (고려대학교, 건축사회환경공학부) ;
  • 원천봉 (고려대학교, 건축사회환경공학부) ;
  • 윤영수 (고려대학교, 건축사회환경공학부)
  • Received : 2021.10.21
  • Accepted : 2021.11.07
  • Published : 2021.12.31
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, pull-out tests were conducted at room temperature, 150 ℃ and 250 ℃ to evaluate the residual bond strength of carbon fiber reinforcement polymer, CFRP after elevated temperature and deformed steel rebar of D10 and D13 were also evaluated after the high temperature heating for comparison. As a result of the experiment, the bond strength of the CFRP after 150 ℃ and 250 ℃ decreased by 9.94 % and 41 %, respectively. On the other hand, after thermal heating, both the steel rebar of D10 and D13 had a lower rate of reduction in bond strength than that of the CFRP. Also slip at the maximum bond strength also decreased after the heating for both the CFRP and the rebars. Through it, the correlation between the bond strength and the slip reduction due to thermal heating was confirmed and bond slip models were presented. Finally the experimental result was evaluated as relative bond strength to identify the residual bond performance of the CFRP and the rebar after the heating was confirmed by comparing with the existing test result of the bond strength after elevated temperature.

본 연구에서는 고온가열 이후의 탄소 보강근의 잔류 부착 강도 평가를 위하여 상온, 150℃에 따른 부착실험을 수행하였으며, 탄소 보강근과의 비교를 위한 D10 및 D13 철근도 고온 가열한 이후 잔류 부착 강도를 평가하였다. 실험 결과, 150℃ 가열 이후 탄소 보강근의 부착 강도는 상온 대비 약 9.94% 감소하였다. 반면 가열 이후 D10 철근 및 D13 철근 모두 탄소 보강근 대비 부착 강도 감소율이 적게 나타났다. 또한 온도 가열 이후 최대부착 강도에서 발생한 슬립도 탄소 보강근과 철근 모두 줄어드는 경향을 보였다. 이를 통해 고온가열에 따른 부착 강도와 슬립 감소의 상관관계를 확인하였으며, 부착-슬립 곡선을 나타내었다. 최종적으로는 실험 결괏값을 상대부착 강도로 나타냄으로써 가열 이후 탄소 보강근 및 철근의 잔류 부착성능을 확인하고자 하였다.

Keywords

Acknowledgement

본 연구는 국토교통부/국토교통과학기술진흥원의 지원으로 수행되었음(과제번호21CFRP-C163381-01).

References

  1. ACI 408R-03. (2003), Bond and Development of Straight Fig. 8 Residual bond strength ratio after elevated temperature Reinforcing Bars in Tension, American Concrete Institute.
  2. ACI 440.1R-15. (2015), Guide for the Design and Construction of Structural Concrete Reinforced with FRP Bars, American Concrete Institute.
  3. ACI 440.6M-08. (2008), Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, American Concrete Institute.
  4. ASTM, C. 39. (2007), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, West Conshohocken, PA; ASTM International
  5. ASTM C. 1609. (2012), Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam with Third-Point Loading). ASTM International.
  6. ASTM D 3916-02. (2002), Standard Test Method for Tensile Properties of Pulltruded Glass-Fiber-Reinforced-Plastic Rods. West Conshohocken, PA; ASTM International
  7. Baena, M., Torres, L., Turon, A., and Barris, C. (2009), Experimental Study of Bond Behaviour between Concrete and FRP Bars Using a Pull-out Test, Composites Part B: Engineering, 40(8), 784-797. https://doi.org/10.1016/j.compositesb.2009.07.003
  8. Banthia, N and Gupta, R. (2004), Hybrid Fiber Reinforced Concrete (HyFRC): Fiber Synergy in High Strength Matrices, Materials and Structures, 37(10), 707-716. https://doi.org/10.1007/BF02480516
  9. Benmokrane, B., Wang, P., Ton-That, T. M., Rahman, H., and Robert, J.-F. (2002), Durability of Glass Fiber Reinforced Polymer Reinforcing Bars in Concrete Environment, Journal of Composites for Construction 6(3), 143-155. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:3(143)
  10. CEB-FIP Model. (2010), CEB-FIB Model Code, Comite Euro-International Du Beton, Thomas Telford, London.
  11. CSA S806-12. (2017), Canadian Standards Association. Design and Construction of Building Structures with Fibre-Reinforced Polymers, Canadian Standards Association. Mississauga, ON, Canada.
  12. Davalos, J. F., Chen, Y., and Ray, I. (2008), Effect of FRP Bar Degradation on Interface Bond with High Strength Concrete, Cement and Concrete Composites 30(8), 722-730. https://doi.org/10.1016/j.cemconcomp.2008.05.006
  13. Ellis, D. S., Tabatabai, H., and Nabizadeh, A. (2018), Residual Tensile Strength and Bond Properties of GFRP Bars after Exposure to Elevated Temperatures, Materials, 11(3), 346-359. https://doi.org/10.3390/ma11030346
  14. Hamad, R. J., Johari, M. M., and Haddad, R. H. (2017), Mechanical Properties and Bond Characteristics of Different Fiber Reinforced Polymer Rebars at Elevated Temperatures, Construction and Building Materials, 142, 521-535. https://doi.org/10.1016/j.conbuildmat.2017.03.113
  15. ISO 834. (1999), Fire-Resistance Tests: Elements of Building Construction-part 1.1: General Requirements for Fire Resistance Testing, INTERNATIONAL ORGANIZATION FOR STANDARDIZATION.
  16. Katz, A., Berman, N., and Bank, L. C. (1999), Effect of High Temperature on the Bond Strength of FRP Rebars, Journal of Composites for Construction, 3(2), 73-81. https://doi.org/10.1061/(ASCE)1090-0268(1999)3:2(73)
  17. Kook, K.H., Shin, H.O., Kwahk, I.J., and Yoon, Y.S. (2010), Bond Characteristics of Ultra High Performance Concrete, Journal of the Korea Concrete Institute, 22(6), 753-760. https://doi.org/10.4334/JKCI.2010.22.6.753
  18. Lee, J. Y., Kim, T. Y., Kim, T. J., Yi, C. K., Park, J. S., You, Y. C., and Park, Y. H. (2008), Interfacial Bond Strength of Glass Fiber Reinforced Polymer Bars in High-Strength Concrete, Composites Part B: Engineering, 39(2), 258-270. https://doi.org/10.1016/j.compositesb.2007.03.008
  19. Lee, Y.H., Choi, J.H., Kim, H.C., Kim, D.H., and Na, S.J. (2008), Experimental Study on Bond Strength of CFRP Rebar in Concrete, Journal of the Architectural Institute of Korea Structure and Construction, 24(11), 53-60.
  20. Moon, D. Y., Sim, J., and Oh, H. (2006), A Study on Methodology for Improvement of Bond of FRP reinforcement to Concrete, Journal of The Korean Society of Civil Engineers, 26(4A), 775-785.
  21. Mouritz, A.P and Gibson, A. G. (2007), Fire Properties of Polymer Composite Materials, Springer Science & Business Media 143
  22. Nigro, E., Bilotta, A., Cefarelli, G., Manfredi, G., and Cosenza, E. (2012), Performance under Fire Situations of Concrete Members Reinforced with FRP Rods : Bond Models and Design Nomograms, Journal of Composites for Construction, 16(4), 395-406. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000279
  23. Okelo, R and Yuan, R. L. (2005), Bond Strength of Fiber Reinforced Polymer Rebars in Normal Strength Concrete, Journal of Composites for Construction, 9(3), 203-213. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:3(203)
  24. Okelo, R. (2007), Realistic Bond Strength of FRP Rebars in NSC from Beam Specimens, Journal of Aerospace Engineering, 20(3), 133-140. https://doi.org/10.1061/(ASCE)0893-1321(2007)20:3(133)
  25. Ozkal, F. M., Polat, M., Yagan, M., and Ozturk, M. O. (2018), Mechanical Properties and Bond Strength Degradation of GFRP and Steel Rebars at Elevated Temperatures, Construction and Building Materials, 184, 45-57. https://doi.org/10.1016/j.conbuildmat.2018.06.203
  26. Pokorny, P., Kolisko, J., Citek, D., and Kostelecka, M. (2020), Effect of Elevated Temperature on the Bond Strength of Prestressing Reinforcement in UHPC, Materials, 13(21), 4990-5010. https://doi.org/10.3390/ma13214990
  27. Yoo, D.Y., Park, J.J., Kim, S.W., and Yoon, Y.S. (2014), Influence of Reinfocing Bar Type on Autogenous Shrinkage Stress and Bond Behavior of Ulta High Peformance Concrete, Journal of the Cement Concrete Composite, 48, 150-161. https://doi.org/10.1016/j.cemconcomp.2013.11.014
  28. Yoo, D. Y and Yoon, Y. S. (2017), Bond behavior of GFRP and Steel Bars in Ultra-High-Performance Fiber-Reinforced Concrete. Advanced Composite Materials, 26(6), 493-510. https://doi.org/10.1080/09243046.2016.1197493
  29. Yuan, T.F., Lee, J.Y., Min, K.H., and Yoon, Y.S. (2019), Experimental Investigation on Mechanical Properties of Hybrid Steel and Polyethylene Fiber-Reinforced No Slump High-Strength Concrete, International Journal of Polymer Science, 2019, 1-11.
  30. Xiao, J and Falkner, H. (2007), Bond Behaviour between Recycled Aggregate Concrete and Steel Rebars, Construction and Building Materials, 21(2), 395-401. https://doi.org/10.1016/j.conbuildmat.2005.08.008