• Progress in Medical Physics
• /
• v.29 no.2
• /
• pp.59-65
• /
• 2018

This paper describes the clinical use of the dose verification of multileaf collimator (MLC)-based CyberKnife plans by combining the Octavius 1000SRS detector and water-equivalent RW3 slab phantom. The slab phantom consists of 14 plates, each with a thickness of 10 mm. One plate was modified to support tracking by inserting 14 custom-made fiducials on surface holes positioned at the outer region of $10{\times}10cm^2$. The fiducial-inserted plate was placed on the 1000SRS detector and three plates were additionally stacked up to build the reference depth. Below the detector, 10 plates were placed to avoid longer delivery times caused by proximity detection program alerts. The cross-calibration factor prior to phantom delivery was obtained by performing with 200 monitor units (MU) on the field size of $95{\times}92.5mm^2$. After irradiation, the measured dose distribution of the coronal plane was compared with the dose distribution calculated by the MultiPlan treatment planning system. The results were assessed by comparing the absolute dose at the center point of 1000SRS and the 3-D Gamma (${\gamma}$) index using 220 patient-specific quality assurance (QA). The discrepancy between measured and calculated doses at the center point of 1000SRS detector ranged from -3.9% to 8.2%. In the dosimetric comparison using 3-D ${\gamma}$-function (3%/3 mm criteria), the mean passing rates with ${\gamma}$-parameter ${\leq}1$ were $97.4%{\pm}2.4%$. The combination of the 1000SRS detector and RW3 slab phantom can be utilized for dosimetry validation of patient-specific QA in the CyberKnife MLC system, which made it possible to measure absolute dose distributions regardless of tracking mode.

• The Journal of the Korea Contents Association
• /
• v.20 no.1
• /
• pp.304-316
• /
• 2020

Laos is rich in natural resources but lacks the capital to develop them. Partly alleviating the shortage is FDI from neighboring countries, especially Thailand. Not only does this contribute to directly increasing GDP by increasing effective demand, it also has an additional GDP increase effect by expanding Laos' production capacity. Laos' exports mostly consist of mineral resources and electricity. This, too, contributes to an increase in GDP by increasing the effective demand. Thailand accounts for more than 40 percent of Laos' exports. This paper tries to confirm the economic impact on Laos in Thailand through a econometric analysis of Laos' GDP, Laos' exports to Thailand and Thailand's FDI to Laos. It turns out that economic ties with Thailand, including exports to Thailand and Thailand's FDI, play a very important role in Laos' economic growth. Laos recently recorded relatively robust economic growth, but its driving force is weak. That's because Laos' growth engines are very limited and have no resilience to external shocks. Moreover, economic growth has not been linked to an increase in employment because the economy is not diversified and growth in the hydroelectric power sector does not lead to growth in other sectors. Given this, Laos needs to actively take advantage of its geographical proximity to Thailand. It is necessary to create a more active environment for the inflow of FDI in Thailand, to foster resource-based and labor-based manufacturing to take advantage of the Thai market.

• Journal of the Economic Geographical Society of Korea
• /
• v.23 no.2
• /
• pp.147-165
• /
• 2020

The aim of this study is to find out Korean electronic industries' production network in Hanoi Red River Delta, Vietnam and its change based on customer-following overseas expansion. In-depth interviews with Korean subcontractors were conducted to examine the characteristics of customer-following overseas expansion of Korean subcontractors. Korean subcontracting corporations in electronic industries have expanded into Vietnam as the suppliers to Korean transnational corporations. Since 1990s, Korean corporations have invested into Vietnam but since late 2000s its industrial and geographical concentration has been shifted from textile and clothing industries in Southern Vietnam to electronics in Northern Vietnam. The customer-following overseas expansion of the subcontractors has emerged in three aspects: physical proximity, asymmetrical inter-firm relations and organizational embeddedness. During the process of customer-following overseas expansion, Korean electronic industry production network was transplanted into Vietnam and partially modified. This is because the company's hierarchy and difficulties in changing its trading relationship have affected the process of advancing into overseas markets. Korean transnational corporations seek to establish a stable suppliers through expansion accompanying with its subcontractors, and providing financial and non-financial support to its subcontractors.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.9
• /
• pp.2294-2304
• /
• 1999

Our research purpose in this paper is to improve the performance of query processing in GIS(Geographic Information System) by enhancing the I/O performance exploiting parallel I/O and efficient disk access. By packing adjacent spatial data, which are very likely to be referenced concurrently, into one block or continuous disk blocks, the number of disk accesses and the disk access overhead for query processing can be decreased, and this eventually leads to the I/O time decrease. So, in this paper, we proposes EPR(Enhanced Parallel R-tree) indexing method which integrates the parallel I/O method of the previous Parallel R-tree method and a packing-based clustering method. The major characteristics of EPR method are as follows. First, EPR method arranges spatial data in the increasing order of proximity by using Hilbert space filling curve, and builds a packed R-tree by bottom-up manner. Second, with packing-based clustering in which arranged spatial data are clustered into continuous disk blocks, EPR method generates spatial data clusters. Third, EPR method distributes EPR index nodes and spatial data clusters on multiple disks through round-robin striping. Experimental results show that EPR method achieves up to 30% or more gains over PR method in query processing speed. In particular, the larger the size of disk blocks is and the smaller the size of spatial data objects is, the better the performance of query processing by EPR method is.

• Journal of Veterinary Clinics
• /
• v.34 no.2
• /
• pp.140-145
• /
• 2017

The goal of this study was to investigate risk factors associated with porcine reproductive and respiratory syndrome (PRRS) in pig farms in the Republic of Korea using logistic regression and a multilevel model. A cross-sectional study was applied to 305 pig farms with a questionnaire-based interview by veterinarians between March 2014 and February 2015. The questionnaire comprised eight categories: proximity to neighbors, disinfection, visitors, vehicles, insecticides, wild animals, gilts, and feeding. In total, 61 questions in eight categories related to pig farm biosecurity were investigated. Farms were classified as PRRS stable or unstable based on the results of an antibody test and PCR. For univariate analysis, keeping production records with computers (OR = 0.283, 95% CI = 0.056 - 1.425), accredited farm with no use of antibiotics (OR = 0.412, 95% CI = 0.134 - 1.269), reviewing health record of semen prior to purchasing (OR = 0.492, 95% CI = 0.152 - 1.589), complete isolation of runt pigs (OR = 0.264, 95% CI = 0.084 - 0.829), compulsory registering for visitors (OR = 0.424, 95% CI = 0.111 - 1.612), keeping records of insecticide history (OR = 0.406, 95% CI = 0.089 - 1.846), routine on-farm monitoring by veterinarians (OR = 0.314, 95% CI = 0.069 - 1.423), and use of on-farm checklist for biosecurity monitoring (OR = 0.313, 95% CI = 0.063 - 1.553) were found to decrease the probability of PRRS infection. Multivariate and multilevel analysis revealed only two factors, complete isolation of runt pigs (OR = 0.165, 95% CI = 0.045 - 0.602 and OR = 0.208, 95% CI = 0.055 - 0.782) and compulsory registering for visitors (OR = 0.106, 95% CI = 0.017 - 0.655 and OR = 0.119, 95% CI = 0.017 - 0.809) were found to decrease the probability of PRRS infection. The intracluster correlation coefficient of a province for multilevel model was 0.05. The results of this study might facilitate biosecurity measures for individual farms to reduce the probability of PRRS infection.

• Journal of Korean Neurosurgical Society
• /
• v.62 no.4
• /
• pp.414-421
• /
• 2019

Objective : To evaluate 3-dimensional magnetic resonance imaging (MRI) of Kambin's safe zone to calculate maximum cannula diameter permissible for safe percutaneous endoscopic lumbar discectomy. Methods : Fifty 3D MRIs of 19 males and 31 females (mean, 47 years) were analysed. Oblique, axial and sagittal views were used for image analysis. Three authors calculated the inscribed circle (cannula diameter) individually, within the neural (original) and bony Kambin's triangle in oblique views, disc heights on sagittal views and root to facet distances at upper and lower end plate levels on axial views and their averages were taken. Results : The mean root to facet distances at upper end plate level measured on axial sections increased from $3.42{\pm}3.01mm$ at L12 level to $4.57{\pm}2.49mm$ at L5S1 level. The mean root to facet distances at lower end plate level measured on axial sections also increased from $6.07{\pm}1.13mm$ at L12 level to $12.9{\pm}2.83mm$ at L5S1 level. Mean maximum cannula diameter permissible through the neural Kambin's triangle increased from $5.67{\pm}1.38mm$ at L12 level to $9.7{\pm}3.82mm$ at L5S1 level. The mean maximum cannula diameter permissible through the bony Kambin's triangle also increased from $4.03{\pm}1.08mm$ at L12 level to $6.11{\pm}1mm$ at L5S1 level. Only 2% of the 427 bony Kambin's triangles could accommodate a cannula diameter of 8mm. The base of the bony Kambin's triangle taken in oblique view (3D MRI) was significantly higher than the root to facet distance at lower end plate level taken in axial view. Conclusion : The largest mean diameter of endoscopic cannula passable through "bony" Kambin's triangle was distinctively smaller than the largest mean diameter of endoscopic cannula passable through "neural" Kambin's triangle at all levels. Although proximity of exiting root to the facet joint is always taken into consideration before PELD procedure, our 3D MRI based anatomical study is the first to provide actual maximum cannula dimensions permissible in this region.

• Journal of Conservation Science
• /
• v.38 no.3
• /
• pp.217-233
• /
• 2022

The remains found in Geumcheok-ri, Gyeongju are located in close proximity to the Ancient Tombs in Geumcheok-ri, Gyeongju (Historic Site) which were built between the late 5th and early 6th centuries, and these tombs are known to belong to the powerful rulers of that area. Using metallurgical techniques, this study was conducted on the iron objects obtained from the excavated remains in Geumcheok-ri, Gyeongju which are presumed to have a close relation to the nearby ruins that played an important role in the growth of Silla. To identify differences in manufacturing techniques based on the purpose of the iron objects, eight objects were selected after classifying them by use and the microstructure and non-metallic inclusions were investigated. The analyses results confirmed that the manufacturing process involved forging iron with a high or low carbon content to produce a particular shape, and that the carburization process was applied to iron post forging a shape to increase its strength when necessary. The mechanical properties were improved by selectively applying the steelmaking method and the heat treatment technique considering the functions of the parts, and the low temperature reduction was applied to the smelting process. Furthermore, in comparison with the iron objects excavated from the remains located in the center of Gyeongju and its outskirts, it is confirmed that there is similarity in the smelting and manufacturing techniques between these objects.

• 한국체육학회지인문사회과학편
• /
• v.57 no.2
• /
• pp.279-289
• /
• 2018

The purpose of this study is to investigate features of leisure and recreation scholarship study in The Korean Journal of physical education based on co-authors network and topic modeling through using Word Cloud and LDA Topic Modeling(Latent Dirichlet Allocation). The data collected for this study are 2,697 papers published online from January 2008 to March 2017 on the Korean journal of physical education. Respectively ordered analysis targets are the major author, author of correspondence, co-author 1, co-author 2, co-author n in related document to explore studies' trends using the 369 documents. As a result, the co-author network analysis result found that 451 were linked to the research network, on average researchers had 1.52 relationships and the average distance between researchers was 2.33. The Representative author's concentration of connection was ranked high in the order of the following, Lee. K. M., Hwang. S. H., H., Lee. C. S., and proximity centers were shown in Seo K. B., Han. J. H., Kim. K. J. Finally, parameter-centric features appeared in order of Lee. C. W. and Seo. K. B. was most actively connected between the researchers of the leisure-related academic papers. Future research needs discussions among scholars regarding the trend and direction of future leisure research.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.5
• /
• pp.481-486
• /
• 2014

This study aims at enhancing the performance of file-referring octree, suggested by Han(2014), for efficiently querying huge 3D point clouds, acquired by the 3D terrestrial laser scanning. Han's method(2014) has revealed a problem of heavy declining in query speed, when if it was applied on a very long tunnel, which is the lengthy and narrow shaped anisometric structure. Hereupon, the shape of octree has been analyzed of its influence on the query efficiency with the testing method of generating an independent octree in each isometric subdivision of 3D object boundary. This method tested query speed and main memory usage against the conventional single octree method by capturing about 300 million points in a very long tunnel. Finally, the testing method resulted in which twice faster query speed is taking similar size of memory. It is also approved that the conclusive factor influencing the query speed is the destination level, but the query speed can still increase with more proximity to isometric bounding shape of octree. While an excessive unbalance of octree shape along each axis can heavily degrade the query speed, the improvement of octree shape can be more effectively enhancing the query speed than increasement of destination level.

• Ocean and Polar Research
• /
• v.27 no.3
• /
• pp.299-309
• /
• 2005

The community structure of meiobenthos was studied in the sediment of Kongfjorden, Spitsbergen of Svalbard Island in the Arctic Sea. Samples of meiobenthos were collected in August, 2003. Meiobenthic organisms were collected by SCUBA and van veen grab or acryl sub-corers 34mm in internal diameter, and were taken from upper sediment to a depth of 3cm at each station. A total of 26 meiofaunal groups were found in the sediment of Spitsbergen in Svalbard Island. Nematodes were the most dominant faunal group. Sarcomastigophorans, benthic harpacticoids, and nauplius larvae of crustaceans, were also important components of the meiobenthic community of Kongsfjorden. All of these low faunal groups were comprised of more than 90% of total meiobenthos at every station. The total density of meiobenthos at each station was highest at station MeG 6 $(3,583{\pm}1,137inds./10cm^2)$, and lowest at station $MeG9(28{\pm}1inds./10cm^2)$. Meiobenthos in general showed the highest density in the upper 1cm layer. This may be associated with food and oxygen supply to subsurface. Harpacticoids showed extreme preference at the surface and little presence in layers deeper than 2cm. These animals may be less resistant to oxygen deficiency, and nauplius also showed the same trend. However, in St. MeG 8 and 9, meiobenthos were dense at depths of more than 0-1cm, at especially at depths of 2-3m because of relatively easy penetration of oxygen. Based on the results of cluster analysis, three meiobenthos assemblages were distinguished: one was in the outer and two were in the inner fjord. Station SCU 5 was grouped with the meiobenthos assemblage located in the outer fjord. The outer ford community was characterised by : 1) a relatively low mean number of meiobenthos taxa, 2) a relatively high density of harpacticods and nauplius. One of the inner ford communities (a group of four nation: MeG 2, 3, 8, 9) was in the proximity of the glaciers. Specifically, it was characterised by : 1) a low mean number of meiobenthos taxa, 2) a low density. The other inner ford community was characterised by both a high density and great mean number of meiofaunal taxa.