• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.10
• /
• pp.1376-1382
• /
• 2013

This paper analyzes the propagation characteristics of lightning surge according to the type of branch line in distribution system. The types of branch line considered are H-type and PI-type. At each type, the length of main feeder is same, while the number and length of branch line are different. The distribution line is modeled and the various lightning locations are simulated by Electromagnetic Transient Program(EMTP). For each lightning, the various measuring points are selected. Based on the simulation results, the propagation characteristics of lightning surge at each measuring point are analyzed. The analyzed results are verified by travelling wave theory.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.798-803
• /
• 2010

This paper describes the characteristics of electromagnetic wave propagation in power transformer. A transformer which is similar to 154 kV single phase on-site transformer unit was provided for the purpose of the experiment. The 12 dielectric windows on the transformer enclosure to install UHF (ultra high frequency) sensors and the full scale mock ups of winding and the core were also equipped in the transformer. Every sensors to be installed to the transformer was tested and verified whether they show same characteristics or not before the experiment. A discharge gap which was used as a PD (partial discharge) source moved to several necessary locations in the transformer to simulate dielectric defects. Propagation times of electromagnetic wave signal from PD source to sensors decided by the routes of both reflection phenomenon and diffraction phenomenon were compared each other. The experimental results showed propagation route of the PD signal makes an effect on the frequency spectrum of front part of the signal and the magnitude of the signal and propagation time of the signal when the signal is captured on the sensor.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1281-1287
• /
• 2000

The studies of probability distribution of the fatigue crack growth life have been somewhat reported. But the study on the probability distribution of the fatigue crack growth life considering the crack coalescence for three dimensional surface fatigue crack has apparently not been reported to date. In this study, the computer program has been developed to predict the probability distribution of the fatigue crack growth life considering the crack coalescence. The effects of parameters for the distribution of the fatigue crack propagation life were evaluated by using the program.

• Wind and Structures
• /
• v.28 no.1
• /
• pp.49-62
• /
• 2019

In this paper, an analytical analysis for the study of vibratory behavior and wave propagation of functionally graded plates (FGM) is presented based on a high order shear deformation theory. The manufacture of these plates' defects can appear in the form of porosity. This latter can question and modify the global behavior of such plates. A new shape of the distribution of porosity according to the thickness of the plate was used. The field of displacement of this theory is present of indeterminate integral variables. The modulus of elasticity and the mass density of these plates are assumed to vary according to the thickness of the plate. Equations of motion are derived by the principle of minimization of energies. Analytical solutions of free vibration and wave propagation are obtained for FGM plates simply supported by integrating the analytic dispersion relation. Illustrative examples are given also to show the effects of variation of various parameters such as(porosity parameter, material graduation, thickness-length ratio, porosity distribution) on vibration and wave propagation of FGM plates.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.7 s.250
• /
• pp.826-832
• /
• 2006

For the improvement of safety and endurance in welded steel structure, it is needed to consider welding residual stress distribution and rolling directional characteristics of materials. In this study, it was investigated experimentally about characteristics of fatigue crack propagation according to welding residual stress and rolling in FCAW(flux cored arc welding) butt-jointed steel plates. SS400 steel plates of 3mm thickness were selected and tested for this study. When the angles between tensile loading direction and rolling direction in welded materials are increased from $0^{\circ}\;to\;90^{\circ}$, their fatigue crack propagation rates are increased. These results are same as predicted increments of fatigue crack propagation rate when stress ratio is increased from 0 to 0.5. When the angles of rolling direction and welding direction to tensile loading direction are $0^{\circ}\;and\;90^{\circ}$ respectively, fatigue crack propagation rate in welded material is lowest.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.59-68
• /
• 1998

In this study, effects of solidification modes (primary $\delta$-ferrite, primary ${\gamma}$-austenite) on the pit initiation and propagation in the 304L and 316L austenitic stainless steel weld metals were investigated. The solidification mode of weld metal was controlled by the addition of nitrogen to Ar shielding gas. Through the electrochemical experiments (potentiodynamic anodic polarization and potentiostatic time-current transient test) and metallographic examination (microstructure and elemental distribution), the following results were obtained. The more the volume content of nitrogen in the shielding gas were, the lower critical current density for passivity was observed. In comparison with weldments solidified through the primary $\delta$-ferrite solidification mode and the primary ${\gamma}$-solidification mode, the former showed higher critical pitting potential and a longer incubation time for stable pit initiation than the latter. However, in the pit propagation stage the former exhibited a faster dissolution rate than the latter. These results were believed to ee related to the distribution of alloying elements such as Cr, Mo, Ni and S.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.5
• /
• pp.79-84
• /
• 2009

Super duplex stainless steel has long life in severe environments by showing the enough strength and corrosion resistance. Therefore, the fracture mechanics approach needs to support the structural strength integrity for the used material. In this study, fatigue crack propagation behavior was investigated to super duplex stainless steel with 0.2% nitrogen. The various volume fraction and distribution of austenite structure for applied specimen in test were obtained by changing the heat treatment temperature and cycle. From test results, fatigue crack propagation rate showed two kinds of tendency between da/dN and ${\Delta}K$ according to distribution of austenite structure and structure anisotropy.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.5
• /
• pp.536-543
• /
• 2009

In this paper the mean stress effects on the probability distribution of the random grown crack size at a specified loading cycle are studied through the fatigue crack propagation tests, which are conducted on the specimens of magnesium alloy under four different stress ratios. Through 80 replicates the probability distributions of the grown crack size are obtained. The goodness-of-fit for probability distributions of the random grown crack size are investigated by Anderson-Darling test and the best fit for those probability distributions is found to be a 3-parameter Weibull distribution. The effects of the mean stress on the probability distribution of the random grown crack size are also estimated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.827-832
• /
• 2003

There has been a number methods for the presentation of time-frequency analysis of non-stationary signal. In this paper, STFT(short time Fourier transform), wavelet transform, Wigner distribution, and higher order Wigner distribution are discussed in details with simulation signals. They are also applied to the analysis of the wave propagation of a semi finite beam. Wigner distribution and higher order Wigner distribution have good time-frewuency resolutions. Wavelet transform is required for impact analysis but should be applied carefully. STFT suffers from time-frequency resolutions. Each method is has its advantage and disadvantage depending on each application signals.

• Earthquakes and Structures
• /
• v.4 no.1
• /
• pp.1-10
• /
• 2013

The present investigation deals with the analysis of wave motion in the layer of an anisotropic, initially stressed, fiber reinforced thermoelastic medium. Secular equations for symmetric and skew-symmetric modes of wave propagation in completely separate terms are derived. The amplitudes of displacements and temperature distribution were also obtained. Finally, the numerical solution was carried out for Cobalt and the dispersion curves, amplitudes of displacements and temperature distribution for symmetric and skew-symmetric wave modes are presented to evince the effect of anisotropy. Some particular cases are also deduced.