• ETRI Journal
• /
• v.42 no.1
• /
• pp.7-16
• /
• 2020

Assuming omnidirectional antenna reception, the ITU-R recently developed a new propagation model on building entry loss (BEL) for 5G millimeter-wave frequency sharing and compatibility studies, which is a simplified outdoor-to-indoor path loss model. Considering the utilization of high-gain narrow-beamwidth beamforming, the omnidirectional-based ITU-R BEL model may not be appropriate to predict propagation characteristics for directional beamforming scenarios. This paper studies the effects of beamwidth on the ITU-R BEL model. This study is based on field measurements collected with four different beamwidth antennas: omnidirectional, 10° horn, 30° horn, and 60° horn. The measurement campaigns were conducted at two types of building sites: traditional and thermally efficient buildings. These sites, as well as the measurement scenarios, were carefully chosen to comply with the ITU-R BEL measurement guidelines and the ITU-R building types. We observed the importance of accurate beam alignment from the BEL variation range. We were able to quantify the beamwidth dependency by fitting to a model that is inversely proportional to the beamwidth.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.3
• /
• pp.103-112
• /
• 1998

This paper proposes a propagation prediction model which can calculate a propagation path loss easily at option point in case of the propagation processing by repeat reflection when we analysis a propagation route, it makes the calculation speed which is the defect of a geometrical of image method and a ray-launching method improve and we develop and apply the algorithms which can do an angle of incidence, an angle of reflection with a propagation direct path, a reflection path and a maximum reflection number arithmetic process synchronously. Finally we choose as a sample which is the real road condition where is around SK telecoms chunnam branch office in wolgok-dong, kwangsan-ku, kwangju and simulate proposition model then we demonstrate the relative superiority with comparing the results.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.559-568
• /
• 2007

This paper presents a new distortion control scheme with a simple estimation model for the propagation errors incurred by dropping some parts of the bitstream in a frame dropping-coefficient dropping (FD-CD) transcoder. The primary goal of this paper is to facilitate bit-rate conversions and rate-distortion controls in the compressed domain without introducing a full decoding and reencoding system in the pixel domain. First, the error propagation behavior over several frame sequences due to coefficient dropping is investigated on the basis of statistical and empirical properties. Then, such properties are used to develop a simple estimation model for the CD distortion accounting for the characteristics of the underlying coded-frame. Finally, the proposed estimation model allows us to determine the amount of coefficient dropping and to effectively allocate rate-distortions into coded-frames. Experimental results show that the proposed estimation model accurately describes the characteristics of propagation errors adaptively in the compressed domain and can be easily applied to distortion control over different kinds of video sequences.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.04a
• /
• pp.63-69
• /
• 2000

Korea Institute of Geology Mining and Materials(KIGAM) cooperating with Southern Methodist University(SMU) has been operating seismo-acoustic array in Chul-Won area to discriminate man-made explosions from natural earthquakes since at the end of July 1999. In order to characterize propagation parameters of detected seismo-acoustic signal and to associate these signals as a blast event accompanying seismic and acoustic signals simultaneously it is necessary to understand infrasound wave propagation in the atmosphere. Two comparable Effective Sound Velocity Structures(ESVS) in atmosphere were constructed by using empirical model (MSISE90 and HWM93) and by aerological observation data of Korea Meteorological Administration (KMA) at O-San area. Infrasound propagation path computed by empirical model resulted in rare arival of refracted waves on ground less than 200km from source region. On the other hand Propagation paths by KMA more realistic data had various arrivals at near source region and well agreement with analyzed seismo-acoustic signals from Chul-Won data. And infrasound propagation in specific direction was very influenced by horizontal wind component in that direction. Linear travel time curve drawn up by 9 days data of the KMA in autumn season showed 335.6m/s apparent sound velocity in near source region. The propagation characteristics will be used to associate seismo-acoustic signals and to calculate propagation parameters of infrasound wave front.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.5
• /
• pp.688-693
• /
• 2022

In this paper, channel propagation path loss was measured in building corridors for frequency bands of 3.7 GHz and 28 GHz, which are used in 5G mobile communication, and compared and analyzed with CI (Close-In) and FI (Floating-Intercept) channel models. To measure the propagation path loss, the measurement was performed while moving the receiver (Rx) from the transmitter (Tx) by 10 m. As a result of the measurement, the PLE (Path Loss Exponent) values of the CI model at 3.7 GHz and 28 GHz were 1.5293 and 1.7795, respectively, and the standard deviations were analyzed as 9.1606 and 8.5803, respectively. In the FI model, 𝛼 values were 79.5269 and 70.2012, 𝛽 values were -0.6082 and 1.2517, respectively, and the standard deviations were 5.8113 and 4.4810, respectively. In the analysis results through the CI model and the FI model, the standard deviation of the FI model is smaller than that of the CI model, so it can be seen that the FI model is similar to the actual measurement result.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.209-219
• /
• 1995

As a new algorithm for RC tree delay estimation, we propose a $\tau$-model of the driver and a moment propagation method. The $\tau$-model represents the driver as a Thevenin equivalent circuit which has a one-time-constant voltage source and a linear resistor. The new driver model estimates the input voltage waveform applied to the RC more accurately than the k-factor model or the 2-piece waveform model. Compared with Elmore method, which is a lst-order approximation, the moment propagation method, which uses $\pi$-model loads to calculate the moments of the voltage waveform on each node of RC trees, gives more accurate results by performing higher-order approximations with the same simple tree walking algorithm. In addition, for the instability problem which is common to all the approximation methods using the moment matching technique, we propose a heuristic method which guarantees a stable and accureate 2nd order approximation. The proposed driver model and the moment propagation method give an accureacy close to SPICE results and more than 1000 times speedup over circuit level simulations for RC trees and FPGA interconnects in which the interconnect delay is dominant.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.63-69
• /
• 2015

The primary aim of this paper is to evaluate the probabilistic fatigue crack propagation models using the residual of a random variable and to present the probabilistic model fit for the probabilistic fatigue crack growth behavior in Mg-Al-Zn alloys under maximum load conditions. The models used in this study were prepared by applying a random variable to empirical fatigue crack propagation models such as the Paris-Erdogan model, Walker model, Forman model, and modified Forman model. It was verified that the good models for describing the stochastic variation of the fatigue crack propagation behavior in Mg-Al-Zn alloys under maximum load conditions were the 'probabilistic Paris-Erdogan model' and 'probabilistic Walker model'. The influence of the maximum load conditions on the stochastic variation of fatigue crack growth is also considered.

• Journal of Advanced Navigation Technology
• /
• v.28 no.3
• /
• pp.278-287
• /
• 2024

In this paper, telemetry link budget model for small launch vehicle is proposed, and telemetry link budget simulator is implemented. The proposed link budget model consist of geometry model and propagation loss model. The geometry model is calculation of look angle between ground station and small launch vehicle. The propagation loss model consist of free space loss, polarization loss, and de-pointing loss which are appropriate to the small launch vehicle flight environment. The proposed propagation loss model can be calculate propagation loss without complex calculation of propagation environments. The link budget simulator is implemented in MATLAB. The simulator calculate look angle, free space loss, polarization loss parameter, de-pointing loss and received signal level in ground station by using position of ground station, routing of small launch vehicle, 3-D radiation patterns of antennas.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.3 no.1
• /
• pp.96-107
• /
• 2009

Worm attacks can greatly distort network performance, and countering infections can exact a heavy toll on economic and technical resources. Worm modeling helps us to better understand the spread and propagation of worms through a network, and combining effective types of mitigation techniques helps prevent and mitigate the effects of worm attacks. In this paper, we propose a mathematical model which combines both dynamic quarantine and passive benign worms. This Passive Worm Dynamic Quarantine (PWDQ) model departs from previous models in that infected hosts will be recovered either by passive benign worms or quarantine measure. Computer simulation shows that the performance of our proposed model is significantly better than existing models, in terms of decreasing the number of infectious hosts and reducing the worm propagation speed.

• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.94-100
• /
• 2012

Radio interference has been occurring in mobile communication services on the southern seashore in Korea. Monitoring the radio interference signal revealed that the main reason for the radio interference was a radio ducting signal coming from the seaside of Japan. In this paper, we have analyzed the effect of interference on WiMAX service using a 2.5 GHz frequency band between Korea and Japan. We focus on the interference scenario from base station to base station and we use the Minimum Coupling Loss (MCL) method for interference analysis and the Advanced Propagation Model (APM) for calculating the propagation loss in ducts. The propagation model is also compared with experimental measurement data. We confirm that the interfering signal strength depends on the antenna height and this result can be applied to deployment planning for each system with an interference impact acceptable to both parties.