• Title/Summary/Keyword: Profile angle

Search Result 615, Processing Time 0.03 seconds

Numerical studies on cavitation behavior in impeller of centrifugal pump with different blade profiles

  • Song, Pengfei;Zhang, Yongxue;Xu, Cong;Zhou, Xin;Zhang, Jinya
    • International Journal of Fluid Machinery and Systems
    • /
    • v.8 no.2
    • /
    • pp.94-101
    • /
    • 2015
  • To investigate the influence of blade profiles on cavitation behavior in impeller of centrifugal pump, a centrifugal pump with five different blade profiles impellers are studied numerically. The impellers with five different blade profiles (single arc, double arcs, triple arcs, logarithmic spiral and linear-variable angle spiral) were designed by the in-house hydraulic design code using geometric parameters of IS 150-125-125 centrifugal pump. The experiments of the centrifugal pump have been conducted to verify numerical simulation model. The numerical results show that the blade profile lines has a weak effect on cavitation inception near blade inlet edge position, however it has the key effect on the development of sheet cavitation in impeller, and also influences the distribution of sheet cavitation in impeller channels. A slight changing of blade setting angle will induce significant difference of cavitation in impeller. The sharp changing of impeller blade setting angle causes obvious cavitation region separation near the impeller inlet close to blade suction surface and much more flow loss. The centrifugal pump with blade profile of setting angle gently changing (logarithmic spiral) has the super cavitation performance, which means smaller critical cavitation number and lower vapor cavity volume fraction at the same conditions.

Study on Evaluation Method of Flow Characteristics in Steady Flow Bench(2) - Comparison of ISM and PIV Measurement (정상유동 장치에서 유동 특성 평가 방법에 대한 연구(2) - ISM와 PIV 측정의 비교)

  • Park, Chanjun;Ohm, Inyong
    • Transactions of the Korean Society of Automotive Engineers
    • /
    • v.23 no.1
    • /
    • pp.139-147
    • /
    • 2015
  • This paper is the second investigation on the evaluation methods of flow characteristics in a steady flow bench. In the previous work, several assumptions used in the steady flow bench were examined and it was concluded that the assumption of the solid rotation might cause serious problems. In this study, intake valve angle is selected as a main parameter for the assessment because the main flow direction to cylinder governed by this angle has the strongest influence on the in-cylinder flow pattern. For this purpose, four heads, which have the different angle, are prepared and the flow characteristics are estimated both by the conventional impulse swirl meter and a particle image velocimetry at 1.75 times bore position apart from the cylinder head, which is widely used plane in the steady flow measurement. The results show that both of the eccentricity and the velocity profile distort the flow characteristics when using the ISM at 1.75 plane, however, the effects of two factors act in the opposite direction. In addition, the profile's influence is much greater than that of the eccentricity.

Aesthetic Rhinoplasty for the Improvement of the Lateral Facial Profile; Image-up Rhinoplasty (얼굴의 측면 윤곽선 개선을 위한 미용 코성형술)

  • Min Sung
    • Archives of Plastic Surgery
    • /
    • v.32 no.2
    • /
    • pp.205-213
    • /
    • 2005
  • There are several characteristics of the nose of orientals. The dorsum of nose is flat and low, the skin is thick with severe tension, the nasal tip is bulbous, the nostril is wide, and the projection of the nose is limited due to a poorly developed alar cartilage with a short columella. In order to improve these untoward characteristics of the nose of Orientals aesthetically, plain augmentation of the dorsum and tip-plasty with conventional methods has been performed by many plastic surgeons. However these conventional rhinoplasty is not enough to obtain satisfactory results when transforming into a more beautiful and aesthetically charming appearance. In order to produce the optimal nasal shape and profile, it is extremely important to consider the aesthetic surgical factors, which are; the position of the nasion, the optimal nasolabial angle(95-100 degree in Orientals), the natural exposure of infra-tip lobule with and columella, the position of the tip defining point in harmony with the dorsal profile and the smooth and natural silhouette of the lateral nasal profile as it descends into the inferior portion of the nose. From April, 2003 to August, 2004, a total of 52 patients underwent open rhinoplasty, adhering to the strict aesthetic principles considered and described priorly. Surgical approach was done through a transcolumella incision and an alar rim incision. The nasal dorsum was augmented with a silicone implant and the shape of the columella and the nasolabial angle were finessed with a silicone strut implant which was placed in between the medial crurae in a manner of a non-visible graft. The nasal tip was corrected by alar cartilage suture technique and onlay graft of shield shaped Alloderm and Gore-Tex. Author obtained the optimal nasal shape and profile aesthetically, and the results, considered satisfactory in all patients without any complications, are as follows; 1. the average increase in nasal length was 2.5 mm, 2. the average decrease in nasal width was 2.1 mm, 3. the average increase in nasal tip projection was 3.2 mm, 4. the changes of nasolabial angles were from 85.5 degree to 94.7 degree, 5. the changes of the angle between the long axis of the external naris was from 101.3 degree to 89.5 degree. In conclusion, this surgical procedure is an effective, reliable and a valuable method in improving the nasal shape, tip projection, nasolabial angle and especially, the lateral facial profile of Orientals aesthetically.

In-process Measurement of Surface Profile using CCD (CCD를 이용한 인프로세스 표면형상의 계측)

  • 이기용;강명창;김정석;조인순
    • Proceedings of the Korean Society of Precision Engineering Conference
    • /
    • 1995.10a
    • /
    • pp.255-258
    • /
    • 1995
  • Surface profile is an important paramerer to evaluate accuracy of machined worpiece. It is necessary to acquire this data by in-process measurement. Recent researchers have introduced Machine Vision technique to achieve it. But it is difficult to apply it to industry field yet. In this study, in-process measuring system of surface profile is developed using CCD camera. The effect of illuminance according to incident angle is investigated and surface profile from surface tester and illuminance graph are compared experimentally.

  • PDF

A Stress Analysis on the Involute-Circular Arc Composite Tooth Profile Gear (인벌류우트-圓弧 合成齒形기어의 應力解析)

  • 탁계래;최상훈;윤갑영
    • Transactions of the Korean Society of Mechanical Engineers
    • /
    • v.11 no.2
    • /
    • pp.198-204
    • /
    • 1987
  • In a new involute-circular arc tooth profile which is composed of an involute curve in the vicinity of pitch point, a circular arc in the addendum part, and a curve in the dedendum part which is generated by the circular arc profile of mating gear tooth profile, the tooth contact stress is calculated analytically and the root fillet stress is calculated by the finite element analysis. The root fillet stress and the Hertzian contact stress of composite tooth profile gear are decreased with increasing the pressure angle and with decreasing the radius of circular arc and unwound angle. Compared with the standard involute gear, the root fillet stress is decreased by 2-15% and the Hertizian contact stress is decreased by 6-24%.

Angle Ring Press Board Characteristic in Accordance with Temperature and Humidity for High Voltage Transformer (온도와 습도에 따른 초고압 변압기용 앵글링 프레스보드 특성)

  • Suh, Wang Byuck
    • Journal of the Korean Institute of Electrical and Electronic Material Engineers
    • /
    • v.33 no.1
    • /
    • pp.60-64
    • /
    • 2020
  • In this study, to develop angle ring pressboards for high voltage transformers, the radius and thickness are modified under the conditions of temperature and humidity. In particular, a pressboard with a thickness of 6 mm and a radius at the angled part were investigated based on the simulation of the principal stress from the angled optimization profile shape. As a result, by the appropriate application of a higher temperature, the solid insulation can be improved to reduce the moisture content for an optimized profile angle of a high voltage transformer. This also results in the improvement of the safety factor by 25%. It is determined that the electrical insulation properties of pressboards in high voltage transformers can be enhanced by improving their properties.

Design of Cutter Profile and the Characteristics of Vibration for Symmetric Screw Rotor (대칭형스크류로터의 커터설계와 진동특성에 관한 연구)

  • 최상훈
    • Journal of KSNVE
    • /
    • v.5 no.2
    • /
    • pp.257-264
    • /
    • 1995
  • We designed the cutter profile for symmetric screw rotor and did vibration experiment of screw rotor manufactured by the designed cutter profile. The results of this study are summarized as follows. (1) We designed the cutter profile of screw rotor (4-6)(5-6) by using numerical analysis program. (2) The maximum amplitude and variation of amplitude of 5-6 profile rotor are about 30 - 36.7% and 10 - 25% smaller than those of 4-6 profile rotor, respectively. (3) As the angular velocity of rotor changes from 100 to 300 rpm, the vibration of X, Y axis in driving shaft of 5-6 profile rotor is about 10 - 20% smaller than that of 4-6 profile rotor.

  • PDF

A STUDY ON THE FACIAL ESTHETIC PREFERENCES AMONG KOREAN YOUTHS: ASSESSMENT OF PROFILE PREFERENCES (한국 젊은이의 안면미 선호경향에 관한 연구 : 얼굴의 측모평가를 중심으로)

  • Song, Sejin;Choi, Ik-chan
    • The korean journal of orthodontics
    • /
    • v.22 no.4 s.39
    • /
    • pp.881-920
    • /
    • 1992
  • This study was designed to assess profile preferences among Korean youths in the year 1992. Facial esthetics was evaluated by means of silhouette profiles, eliminating the influence of a number of aspects that may affect judgment when normal lateral photographs are used. The main points of preference to be clarified here are as follows. First, on facial convexity, Second, on nasion depth, Third, on mentolabial sulcus depth, Fourth, on the position of upper and lower lips, Fifth, on facial type according to Angle's classification of malocclusion, Sixth, on Song's tangents. The 54 subjects printed in questionnaire as black and white silhouettes were selected from 300 tracings from cephalometric radiographs of people whose age ranging from 11 to 20 years. Photographs of six female subjects were retouched by computer graphic software and printed in color and black/white photographs which were used for adaptation of eyes of participants in selecting profiles in silhouette. They constitute 2 questions. The 54 subjects were grouped as 22 questions, each of them composed of 6 subjects, according to the aspects to be clarified. Twenty four questions in total were asked to assess profile preferences. For the assessment, the profile line, the facial esthetic triangle, Song's tangents, and Angle's classification of malocclusion were introduced. The profile line is composed of 11 component points which are Trichion, Glabella, Nasion, Pronasale, Subnasale, Labrale superius, Stomion, Labrale inferius, Supramentale, Pogonion, and Gnathion. The facial esthetic triangle is composed of 3 tangents: A-tangent which is the tangent of dorsum of nose, B-tangent which is the line passing through Sn and Ls, and C-tangent which is drawn on the turning point of the curve which lies between mentolabial sulcus (Sm) and pogonion (Pg). Angle's classification has 3 types of malocclusion which are Class I, Class II, and Class III. Class II malocclusion is subdivided into Division 1 and Division 2. The participants of the survey were composed of 861 college students (448 male students, 413 female students) whose majors grouped as Fine Arts. Liberal Arts, and Natural Sciences, and whose mean age 21.8 years. The statistics program SPSS/PC + of SPSS Inc. was used to analyze answers of participants. Crosstabulation, Chi-square test, and Kendall test were done. The conclusions are as follows: First, Korean youths have a tendency to prefer the slightly convex face to the flat or concave face. Second, they prefer a moderately deep nasion. Third, they prefer a moderately deep mentolabial sulcus. Fourth, they prefer the position of lips which are near to Ricketts' E-line. The position of the upper lip which is slightly posterior to E-line is preferred. The upper lip which lies too far anterior or posterior to the lower lip is not perferred. Fifth, they prefer most, according to Angle's Classification of Malocclusion, Class I facial profile which has a slight inclination to Class II division 2. The order of preference is Class I, Class II division 2, Class III, and Class II division 1. Sixth, they prefer the type 2 and 3 of Song's tangents. The facial profile within which A-and B-tangent meet is preferred. The facial profile which has Cotangent that .meets with A-tangent slightly posterior to the crossing point of A-and B-tangent or that parallels with B-tangent is preferred.

  • PDF

Rotation Angle Estimation Method using Radial Projection Profile (방사 투영 프로파일을 이용한 회전각 추정 방법)

  • Choi, Minseok
    • Journal of Convergence for Information Technology
    • /
    • v.11 no.10
    • /
    • pp.20-26
    • /
    • 2021
  • In this paper, we studied the rotation angle estimation methods required for image alignment in an image recognition environment. In particular, a rotation angle estimation method applicable to a low specification embedded-based environment was proposed and compared with the existing method using complex moment. The proposed method estimates the rotation angle through similarity mathcing of the 1D projection profile along the radial axis after converting an image into polar coordinates. In addition, it is also possible to select a method of using vector sum of the projection profile, which more simplifies the calculation. Through experiments conducted on binary pattern images and gray-scale images, it was shown that the estimation error of the proposed method is not significantly different from that of complex moment-based method and requires less computation and system resources. For future expansion, a study on how to match the rotation center in gray-scale images will be needed.

A ROENTGENOCEPHALOMETRIC STUDY OF SOFT TISSUE PROFILE FOR THE CHILDREN IN THE DECIDUOUS DENTITION (유치열기(乳齒列期) 아동(兒童)의 악안면연조직(顎顔面軟組織)의 두부방사선(頭部放射線) 계측학적(計測學的) 연구(硏究))

  • Kim, Dong-Phil;Kim, Nam-Hong
    • Journal of the korean academy of Pediatric Dentistry
    • /
    • v.11 no.1
    • /
    • pp.191-213
    • /
    • 1984
  • This study was made on the facial profile of the normal Korean children using the roentgenographic cephalograms. The subjects consisted 51 males and 47 females children of primary dentition with the normal occlusion and acceptable profile. For this study 13 soft tissue profile landmarks were plotted and 14 liner length, 9 soft tissue thickness, 8 vertical height length, 12 angles of soft tissue profile, and 2 vertical proportion were measured. The mean and standard deviations in the subjects were calculated and compared between male and female. The following results were obtained : 1. By the significant test, total facial convexity angle and soft tissue thickness were no significant difference between both sexes. 2. Lower facial height was greater than upper facial height in both sexes. 3. The vertical length of the upper and lower lips were 21.95 mm, 40.74 mm in male and 21.62 mm, 39.63 mm in female. 4. In the relationship of the upper lip and lower lip to the Ricketts' esthetic line, the male was 1.3 mm, 1.18 mm and the female was 1.16 mm, 1.27 mm front of the esthetic line. 5. Compared with the angulation of flush terminal plane group and mesial step group, the mesial step group was greater than the flush terminal plane group except the chin angle.

  • PDF