• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.231-235
• /
• 1999

Cooling characteristics of cooling jacket for spindle system with built-in motor are studied. for the analysis, three dimensional model for the cooling jacket is built by using finite volume method. The three dimensional model includes the estimation on the amount of heat generation of bearing and built-in motor and the thermal characteristic values such as heat transfer coefficients on the boundary. The temperature distributions and the cooling characteristics are analyzed by using the commercial software FLUENT. Numerical results show that stream-wise cross section area and flow rate are important factors for cooling characteristics of cooling jacket. Cooling performance of cooling jacket is good in condition that stream-wise cross section's horizontal length is close to its vertical one and flow rate is high. This results show that heat transfer is dominated by velocity profile and heat transfer area.

• 방사성폐기물학회지
• /
• 제15권2호
• /
• pp.173-180
• /
• 2017

본 연구에서는 한국원자력연구원의 핵연료가공시설 굴뚝 내에서 9곳의 시료채취 위치를 선정하여 ANSI/HPS N13.1-1999 지침에서 제시하는 기준에 따라 그 적절성을 평가하였다. 유체를 포함한 다중물리 해석 소프트웨어인 COMSOL을 활용하여 유동교란 지점으로부터 굴뚝 직경의 배수 높이 위치(L/D) 단면에서의 속도분포, 유동각 및 $10{\mu}m$ 크기의 입자분포 등의 항목에 대하여 기준만족 여부를 평가하였다. 평가 결과, 5 L/D 이상에서 속도분포에 대한 기준을 만족했으며, 평균 유동각에 대한 기준은 모든 위치에서 만족했다. 입자분포에 대한 기준은 5 L/D 와 9 L/D 에서 만족하였으나, 그 분포가 일부에서 기준을 만족하지 못하였다. 균일한 입자분포를 얻기 위한 방법으로 굴뚝 내 정적 혼합장치(static mixer)와 둘레링(perimeter ring)을 추가하는 것을 제안하고, 이에 대한 평가를 수행하였다. 정적 혼합장치를 추가한 경우에는 5-10 L/D, 둘레링을 추가한 경우에는 5 L/D 및 7-10 L/D 에서 입자분포에 대한 기준을 만족하였다. 보완을 위하여 추가한 2 가지 조건에서, 입자분포에 대한 기준을 만족하는 지점은 속도분포 및 평균 유동각에 대한 기준 역시 만족하고 있음을 확인하였다. 본 연구에서 사용한 방법은 신규시설뿐만 아니라, 현장입증시험 수행이 어려운 운영중인 시설에 대하여 시료채취 위치의 적절성을 평가하기 위한 방법으로 활용될 수 있다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 춘계학술대회논문집
• /
• pp.145-155
• /
• 1996

The extrusion velocity of billet through a die and the shapes of the die are the important factors in the metal forming process of the extrusion of billet. in recent years, the life cycle of products is goingfaster. Although the former finite element method was capable of yielding a detailed analysis, it requires lots of time and extensive coding effort. Then, some simple devices were developed and based on upper bound method. For this purpose , a kinematically admiasible velocity field is formulated for extrusion of cylinders with arbitrary cross section and die profile on their outer surfaces by using a modified upper bound approach, which configures simulataneous extruding speeds in three directions . Also, In order to display mesh of the cold forward extrusion process using the approach , the automatic three-dimentional mesh generation produced by the approach coupled finite element method with upper bound method.

• 한국군사과학기술학회지
• /
• 제23권1호
• /
• pp.59-65
• /
• 2020

Many technologies are being studied to reduce the RCS(Radar Cross Section) of stealth aircraft. Most RCS-reduction technlogies correspond to platforms. It is important to identify factors that RCS performance through simulation analysis of aircraft Mounted equipment. In particular, there are no studies of RCS performance in the radar frequency band when antenna transmit signals are applied. In this paper, the RCS performance variation on the transmit signal on/off of antennas mounted on a stealth aircraft was verified. Antennas were selected for each frequency band and simulated analysis to the RCS performance changes during antenna transmitting signal. Finally, to verify the characteristics of the change in RCS performance, RCS test measurements on the low-profile antenna transmit signal on/off were performed. In addintion, antenna RCS test measurement was performed according to the change of transmit signal power output. As a result, it was confirmed that there is no change in RCS performance when an antenna transmit signal is applied.

• 대한기계학회논문집B
• /
• 제33권7호
• /
• pp.512-519
• /
• 2009

Flow pulsation in the gap connecting with two parallel channels is investigated by RANS and URANS approaches. The two parallel channels are connected by a small channel called for a gap. The parallel channels are designed to have different cross section area with its ratio of 0.5. Computations are conducted using a CFX 11.0 code. The bulk Reynolds number is 60,000. Predicted results are compared with the previous experimental data. Mean velocity profile at the center of gap region are compared with experiments for its validation. Spectral analysis on the lateral velocity in the center of the gap was performed. Auto correlation for the axial-flow velocity pattern was presented. The unsteady structure of the flow pulsation was visualized in the region of the gap in the parallel channel.

• Journal of the Korean Wood Science and Technology
• /
• 제51권6호
• /
• pp.493-508
• /
• 2023

Round timber materials of 600 mm length, cut from large-cross-section round timber of red pine (Pinus densiflora S. et Z.) of 450 mm width and 4.2 m length, were prepared as the target of kiln drying in this study. After treating the target materials through end sealing (ES), end sealing - kerfing (ES-K), lateral sealing - end sealing - boring (LS-ES-B), or lateral sealing - partial end sealing (LS-PES), the effects of the treatment on the incidence of drying defects were determined. The target materials with exposed lateral surface and sealed cross surface were steamed at the initial temperature of 65℃ above the official pest control temperature of 56℃, followed by kiln drying toward the final temperature of 75℃. The target materials with sealed lateral surfaces, on the other hand, were dried at the initial temperature of 90℃ at almost the maximum temperature of conventional kiln drying, as there is no risk of early check formation caused by surface moisture evaporation. The final temperature was set at approximately 100℃. The drying time, taken for the target materials with initial moisture content of 70%-80% to reach the target moisture content of 19%, varied across treatment conditions. The measured drying time was 1,146 hours (approximately 48 days) for the timber with sealed cross surface and 745 hours (approximately 31 days) for the timber with sealed lateral surface, until the moisture content reached the target level. The formation of surface checks could not be prevented in the control and ES groups, but a definite preventive effect was obtained for the LS-ES-B and LS-PES groups.

• 한국전자파학회논문지
• /
• 제29권7호
• /
• pp.532-539
• /
• 2018

본 논문에서는 3대의 광대역 레이다에서 얻어지는 각각의 고 분해능 거리 프로파일(high resolution range profile: HRRP)을 이용하여 유도탄의 위치를 추정하는 방법에 대하여 제시한다. 레이다는 유도탄의 레이다유효반사면적(radar cross section: RCS)이 큰 표면에 반사되어 돌아오는 신호를 이용하여 거리를 측정한다. 하지만, 레이다에서 유도탄의 표면과 원점 사이의 거리 획득은 어렵다. 이를 보완하기 위하여 유도탄의 이동방향과 레이다의 추적 방향 사이의 각도를 알아내고, 유도탄의 표면에서 원점까지의 거리를 계산하여 레이다 측정 거리에 보상하였다. 따라서 3대의 레이다로부터 유도탄 원점까지의 총 거리를 계산하여 유도탄의 위치를 추정하였다. 전자기 수치해석 프로그램을 이용하여 유도탄 자세 변화에 따른 레이다의 거리 보상을 시뮬레이션 검증하고, 500 MHz 대역폭의 고 분해능 레이다에서 계측한 거리 프로파일을 이용하여 유도탄의 위치를 추정하였다.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.158-165
• /
• 1994

Cu-Cr alloy thin film requires good quality of etching be used for TAB technology. The etched cross sec-tion was clean enough when the etching was performed in 0.1M $FeCl_3$ solution at $50^{\circ}C$. The etching rate was increased with the amount of $KMnO_4$. For enhanced profile of cross section and rate, the spray etchning was found to be superior compared to the immersion etching. A series of experiments were performed to improve the uniformity of the current distribution in electrodeposition onto the substrate with lithographic patterns. Copper was electrodeposited from quiescent-solution, paddle-agitated-solution, and air-bubbled-solution to in-vestigate the effect of the fluid flow. The thickness profile of the specimen measured by profilmetry has the non uniformity at feature scale in quiescent-solution, because of the longitudinal vortex roll caused by the natural convection. However, uniform thickness profile was achieved in paddle-agitated or air bubbled solu-tion.

• 융복합기술연구소 논문집
• /
• 제3권2호
• /
• pp.17-21
• /
• 2013

Hot cross wedge rolling process as an incremental forming has many advantages such as the material usage, the short process time, the automatic equipment line and the low forming load. However, it occurs some defects such as the surface groove, the axis warping and the Mannesmann hole. In this paper, the defect of the Mannesmann hole was carried out. Finite element analysis was utilized to reveal the stress distribution, the rotation of the specimen and the change of section profile. Cross wedge rolling experiment was also conducted on the generation of the Mannesmann hole. It was demonstrated according to the spreading angle with respect to the various types of material. In the view point of metal flow, the smaller forming angle and the larger spreading angle increase opportunities of the defect hole generations.

• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.24-29
• /
• 2015

The current waveform was analysed to monitor the weld quality in real time process. The acquired current waveform was discretely analysed for the top and bottom limits of peaks as well as the pulse frequency measurement. Fast Fourier Transform was implemented in the program to monitor the pulse frequency in real time. The developed algorithm or program was tested for the validation purpose. The cross-section of weld profile was compared to the current waveform profile to correlate the monitored signal and the actual parts. Pulse frequency was also used as auxiliary tool for the quality monitoring. Based on the results, it was possible to evaluate the quality of welding by measure the current waveform profile and frequency measurement.