• Journal of Food Hygiene and Safety
• /
• v.27 no.2
• /
• pp.109-116
• /
• 2012

The study indicated that antimicrobial activity about gram positive and gram negative bacteria of ginger-oleoresin(GO) extract with the condition of ethanol and supercritical fluid extractions. As the concentration of extraction increases, the clear zone of GO ethanol extract also increased dependently. This led the antimicrobial activity of gram positive bacteria to take bigger place than gram negative bacteria especially in Listeria monocytogenes. There was a high antimicrobial activity in E-III treatment where the ratio of the ginger powder extract to ethanol extraction was 1:6. It was quite effective to treat the antimicrobial activity of GO ethanol extract under $80^{\circ}C$ and there was not big difference in the intervals which were the extraction time - 1 to 7 hours. The antimicrobial activity of supercritical fluid extract seemed to take the biggest place in Listeria monocytogenes. From the supercritical fluid extract, it was shown the strong ability of antimicrobial activity in the condition with 100 bar $35^{\circ}C$, 250 bar $35^{\circ}C$ and 250 bar $65^{\circ}C$. Furthermore, according to the case of solvent extract, there was not any significant difference in the antimicrobial activity with condition of extraction. However, there was significant antimicrobial activity in E-III treatment of 100 bar and 500 bar of extraction pressure, and $35^{\circ}C$ and $65^{\circ}C$ of extraction temperature.

• Transactions of Materials Processing
• /
• v.10 no.7
• /
• pp.558-564
• /
• 2001

An experimental modeling is applied to investigate the formation of forms in molten aluminum By using a specially designed equipment, the effect of process variables, such as the shape of stirrer, stirring velocity and fluid viscosity, on the formation of foams were studied in the glycerine added water. Bubbles formed in water had various diameter from 1 to 10 mm and the number of bubbles was 0 to 20/$cm^2$. It turned out that among various variables the stirring velocity and fluid viscosity played important roles on the formation of bubbles. The results obtained from the model experiment were preyed to be convincible also in the real aluminum foam.

• Fibers and Polymers
• /
• v.5 no.2
• /
• pp.160-169
• /
• 2004

Polystyrene/layered silicate nanocomposites were prepared by melt intercalation. To examine the distribution of the clay in polymer matrix, small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) were used. Intercalated nanocomposites were obtained and their rheological properties were investigated. Microcellular nanocomposite foams were produced by using a supercritical fluid. As clay contents increased, the cell size decreased and the cell density increased. It was found that layered silicates could operate as heterogeneous nucleation sites. As the saturation pressure increased and the saturation temperature decreased, the cell size decreased and the cell density increased. Microcellular foams have different morphology depending upon the dispersion state of nanoclays.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.349-352
• /
• 2001

Shape separation method - a separation process which utilizes the fact that particles of different shape behave differently in force fields- is regarded as an useful measure for recycling, mineral processing, upgrading powdered material and so on. In this study, a trial was given to shape separation method using fluid field to recover pure diatom skeleton - which is thought to have many uses in itself and potential for various applications -from low grade diatomaceous earth of southeastern part of the Korean Peninsula. The striking difference of shape between diatom skeleton and other minerals like clay and quartz made it natural to choose shape separation method. Considering the size of particles to be separated, among many possible methods of shape separation, hydrodynamic field using hydrocyclone was adopted. And it resulted in recovery of pure diatom skeleton with high purity

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.30-39
• /
• 2014

We report in this paper the analysis of the motion of a needle and a spring in a viscous fluid under the influence of gravitational force. Lateral shift as well as vertical motion of a needle falling in a viscous fluid has been observed from a simple experiment. We also observed the combined rotation and translation of a falling spring. The trajectory and velocity of the falling needle and the spring were obtained by using an image processing technique. We also conducted numerical simulation for both problems. For the falling-needle problem, we employed a theory; but it turns out that significant correction is required for the solutions to match the numerical and experimental data. For the falling spring problem various theoretical formula were tested for their justification, but none of the existing theories can successfully predict the numerical and experimental results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.5
• /
• pp.510-517
• /
• 2004

A fine hot-wire is used both as a heating element and a temperature sensor in transient hot-wire method. The traditional sensor system is unnecessarily big so that it takes large fluid volume to measure the thermal conductivity. To dramatically reduce this fluid volume, a new sensor fabrication and a data processing method are proposed in this article. Contrast to the conventional and most popular two wire sensor, the new sensor system is made up of divided multiple long and short wires. Through validation experiments, it is found that the measured thermal conductivities of the glycerin are exactly same each other between the conventional and proposed new method. Also some technical considerations in arranging the multiple wires are briefly discussed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.144-153
• /
• 2009

It is widely known that no-slip assumptions are often violated on regular basis in micrometer- or nanometer-scale fluid flow. In the case of cavity-filling process of nanoimprint lithography(NIL), slip phenomena take place naturally at the solid-to-liquid boundaries, that is, at the mold-to-polymer or polymer-to-substrate boundaries. If the slip or partial slip phenomena are promoted at the boundaries, the processing time of NIL, especially of thermal-NIL which consumes more tact time than that of UV-NIL, can be significantly improved. In this paper it is aimed to elucidate how the cavity-filling process of NIL can be influenced by the slip phenomena at boundaries and to what degree those phenomena increase the process rate. To do so, computational fluid dynamics(CFD) analysis of cavity filling process has been carried out. Also, the effect of mold pattern shape and initial thickness of polymer resist were considered in the analysis, as well.

• Microbiology and Biotechnology Letters
• /
• v.17 no.3
• /
• pp.269-272
• /
• 1989

In order to obtain monoclonal antibody from ascites fluid at sufficiently high purity using a single hydroxylapatite chromatography (HA) a further optimization on its operating variables was carried out. By adjusting the pH of the eluent, the sodium phosphate buffer, to 6.0 from 6.8 and adding CaCl$_2$to 1 mM at the column inlet, the elution molarities (M$_{elu}$) for the desired monoclonal antibody and contaminating proteins can be distinguished from each other with enough resolution. Previously these two groups of proteins co-eluted at the same time at pH 6.8 and without CaCl$_2$. This sin81e step hydroxylapatite chromatography yields the desired antibody pure enough for diagnostic use.

• Journal of the Korean Society of Visualization
• /
• v.19 no.1
• /
• pp.81-87
• /
• 2021

Extensional flow of viscoelastic fluids is widely utilized in various industrial processes such as electrospinning, 3D printing and plastic injection molding. Extensional rheological properties, such as apparent viscosity and relaxation time, play an important role in the design and evaluation of the viscoelastic fluid-involved processes. In this work, we propose a lab-built capillary breakup extensional rheometer (CaBER) based on flow image processing to investigate the capillary breakup of polyethylene oxide (PEO) solution and its extensional rheological properties. We found that the apparent extensional viscosity and extensional relaxation time of the PEO solution are independent of the strike time. The proposed CaBER is expected to be applied to characterization of the extensional rheological properties of viscoelastic fluids at low cost with high precision.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.3 s.24
• /
• pp.14-22
• /
• 2004

Bileaflet mechanical valves have the complications such as hemolysis and thromboembolism, leaflet damage, and leaflet break. These complications are related with the fluid velocity and shear stress characteristics of mechanical heart valves. The first aim of the current study is to introduce fluid-structure interaction method for calculation of unsteady and three-dimensional blood flow through bileaflet valve and leaflet behavior interacted with its flow, and to overcome the shortness of the previous studies, where the leaflet motion has been ignored or simplified, by using FSI method. A finite volume computational fluid dynamics code and a finite element structure dynamics code have been used concurrently to solve the flow and structure equations, respectively, to investigate the interaction between the blood flow and leaflet. As a result, it is observed that the leaflet is closing very slowly at the first stage of processing but it goes too fast at the last stage. And the results noted that the low pressure is formed behind leaflet to make the cavitation because of closing velocity three times faster than opening velocity. Also it is observed some fluttering phenomenon when the leaflet is completely opened. And the rebounce phenomenon due to the sudden pressure change of before and after the leaflet just before closing completely. The some of time-delay is presented between the inversion point of ventricle and aorta pressure and closing point of leaflet. The shear stress is bigger and the time of exposure is longer when the flow rate is maximum. So it is concluded that the distribution of shear stress at complete opening stage has big effect on the blood damage, and that the low-pressure region appeared behind leaflet at complete closing stage has also effect on the blood damage.