• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.26-34
• /
• 1998

This paper presents a characterization method for faults of circuit patterns on MCM(Multichip Module) or PCB(Printed Circuit Board) substrates with electron beams of a SEM(Scanning Electron Microscope) by inducing voltage contrast on the signal line. The experimentation employes dual potential electron beams for the fault characterization of circuit patterns with a commercial SEM without modifying its structure. The testing procedure utilizes only one electron gun for the generation of dual potential electron beams by two different accelerating voltages, one for charging electron beam which introduces the yield of secondary electron $\delta$ < 1 and the other for reading beam which introduces $\delta$ > 1. Reading beam can read open's/short's of a specific net among many test nets, simultaneously discharging during the reading process for the next step, by removing its voltage contrast. The experimental results of testing the copper signal lines on glass-epoxy substrates showed that the state of open's/short's had generated the brightness contrast due to the voltage contrast on the surface of copper conductor line, when the net had charged with charging electron beams of 7KV accelerating voltages and then read with scanning reading electron beams of 2KV accelerating voltages in 10 seconds. The experimental results with Au pads of a IC die and Au plated Cu pads of BGA substrates provided the simple test method of circuit lines with 7KV charging electron beam and 2KV reading beam. Thus the characterization method showed that we can test open and short circuits of the net nondestructively by using dual potential electron beams with one SEM gun.

• Journal of the Korean earth science society
• /
• v.39 no.2
• /
• pp.164-177
• /
• 2018

Even though various geological attractions are distributed domestically, the geological attractions are rarely utilized as field course site. The purpose of this study is to make Seonangbawi area as the field course site after geological investigations are carried out in detail. Seonangbawi is located about 1km southeast from Songjiho beach in Gangwon-do. Seonangbawi area is simply composed of Cretaceous Seokcho granite with the overlay of Quaternary alluvium. Geological field course in the Seonangbawi area will be useful to the student and citizen for developing the knowledge of geological phenomena, such as the formation of granite and minerals, and weathering process. In addition, the student and citizen can develop the knowledge of the geological structures, such as joint (N50E/80NW, N40W/84SW), fault (N42W/83SW), foliation (N32E/54SE), and dyke (N35E/40SE, N26W/63SW), and geographical features, such as tor, taforni, groove, and gnamma in the field. Accordingly, the Seonangbawi area is the best place to learn various geological and geographical phenomena and to discuss the origin of Seonangbawi with limited space.

• Journal of KIISE:Computer Systems and Theory
• /
• v.29 no.6
• /
• pp.331-339
• /
• 2002

This paper presents a garbage collection protocol for checkpoints and message logs which are staved on the stable storage or volatile storage for fault tolerancy. The previous works of garbage collections in coordinated checkpointing protocol delete all the checkpoints except for the last checkpoints on earth processes. But implemented in top of reliable communication protocol like as TCP/IP, rollback recovery protocol based on only last checkpoints makes sympathetic rollback. We show that the old checkpoints or message logs except for the last checkpoints have to be preserved in order to replay the lost message. And we define the conditions for garbage collection of checkpoints and message logs for lost messages and present the garbage collection algorithm for checkpoints and message logs in coordinated checkpointing protocol. Since the proposed algorithm uses process information for lost message piggybacked with messages, the additional messages for garbage collection is not required The proposed garbage collection algorithm makes 'the lazy garbage collectioneffect', because relying on the piggybacked checked checkpoint information in send/receive message. But 'the lazy garbage collection effect'does not break the consistency of the whole systems.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.4
• /
• pp.327-343
• /
• 2004

During tunnel construction, ground failures often occur due to existence of weak zones, such as faults, joints, and cavities, ahead of tunnel face. It is hard to detect effectively weak zones, which can lead underground structure to fail after excavation and before supporting, by using conventional characterization methods. In this study, an enhanced analytical method of predicting weak zones ahead of tunnel face is developed to overcome some problems in the conventional geophysical exploration methods. The analytical method is based on Coulomb's and Gauss' laws with considering the characteristics of electric fields subjected to rock mass. Using the developed method, closed form solutions are obtained to detect a spherical shaped zone and an oriented fault ahead of tunnel face respectively. The analytical results suggest that the presence of weak zones and their sizes, location, and states can be accurately predicted by combining a proper inversion process with resistance measured from several electrodes on the tunnel face. It appears that the skin depth or resistivity in rock mass is affected by the diameter of tunnel face, natural electric potential and noises induced by experimental measurement and spatial distribution of uncertain properties. The developed analytical solution is verified through experimental tests. About 1800 concrete blocks of 5cm by 5cm by 5cm in size are prepared and used to model a joint rock mass around tunnel face. Weak zones are simulated ahead of tunnel face with a material which has relatively higher conductivity than concrete blocks. Experimental results on the model test show a good agreement with analytical results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.2
• /
• pp.1-11
• /
• 2020

As an important basic building block of the smart grid environment, smart meter provides real-time electricity consumption information to the utility. However, ensuring information security and privacy in the smart meter data aggregation process is a non-trivial task. Even though the secure data aggregation for the smart meter has been a lot of attention from both academic and industry researchers in recent years, most of these studies are not secure against internal attackers or cannot provide data integrity. Besides, their computation costs are not satisfactory because the bilinear pairing operation or the hash-to-point operation is performed at the smart meter system. Recently, blockchains or distributed ledgers are an emerging technology that has drawn considerable interest from energy supply firms, startups, technology developers, financial institutions, national governments and the academic community. In particular, blockchains are identified as having the potential to bring significant benefits and innovation for the electricity consumption network. This study suggests a distributed, privacy-preserving, and simple secure smart meter data aggregation system, backed up by Blockchain technology. Smart meter data are aggregated and verified by a hierarchical Merkle tree, in which the consensus protocol is supported by the practical Byzantine fault tolerance algorithm.

• The Korean Society of Law and Medicine
• /
• v.19 no.1
• /
• pp.143-163
• /
• 2018

Implant procedure belongs to so called a commercialized medical treatment, its procedure is simple and clear, and the possibility of success is almost 100%. In addition, it is a selective method rather than an inevitable method for a patient's health, so the importance of liability for explanation is especially emphasized for protection of autonomous decisions by patients. Considering these characteristics, the plaintiff in the relevant case said that the contract of implant procedure has the characteristic of subcontract, and only the failure of implant itself and the violation of liability for explanation should be the defendant's fault liability. In addition, although the above procedure contract is considered as delegation rather than subcontract, whether it's the defendant's malpractice should be judged by general people's common sense rather than average people in the industry. Therefore, if all the implanted teeth were removed due to bleeding and pains, and the patient suffered from dysaesthesia during the process, the defendant's malpractice is fully proved. When the judgements of implant medical malpractice were researched, the court doesn't consider implant contract as subcontract, but it judges dentist's malpractice by whether the implant itself is successful, so it seems that the court acknowledges similar characteristics with subcontract whose purpose is completion of work to some degree. In addition, considering the detailed contents of presented medical malpractices, it seems that judging medical malpractice is based on the common sense of general people. Therefore, the argument of the plaintiff is valid when the fact the adjustment amount is relevant to the amount that the plaintiff initially claimed is considered even though the relevant case was decided to be compulsory mediation.

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.1
• /
• pp.67-83
• /
• 2008

The sericite ore deposits formed in the Precambrian granitic rock at the Bonghwa area, Kyungsangbuk-do, South Korea. The geochemical and mineralogical characteristics of sericite occurred in Daehyun and Seonghwang mine were analyzed using petrographic microscope, XRD, EPMA, XRF and ICP. An alteration mechanism was also studied. Sericitization occurred within the granitic rock by hydrothermal alteration. From the careful study on the occurrence and mineral assemblage, four alteration zone were clearly identified. These zones reflect progressive hydrothermal alteration process. All sericites belong to $2M_1$ polytype and their mineralogical and geochemical properties are close to illite. The sericite ores show various colors, but the characteristics of major element compositions and crystal structures are not different. The trace element analysis, however, indicates that the difference in color attribute to the abundance of Cr and Ti: bluish green colored sericite are enriched in Cr and blackish green colored sericite enriched in Ti. The formation of sericite ore deposit in the granitic rocks are closely relate to fracture system such as fault and joint. It is considered that the sericite ore deposits in this area were formed by very simple hydrothermal alteration occurred along the fracture zones in granitic rocks with absence of other hydrothermally altered minerals such as kaolin and pyrophyllite.

• Journal of KIISE
• /
• v.42 no.4
• /
• pp.434-441
• /
• 2015

Next generation memory technologies, which we denote as 'new memory', have both non-volatile and byte addressable properties. These characteristics are expected to bring changes to the conventional computer system structure. In this paper, we propose a fast boot technique for hybrid main memory architectures that have both new memory and DRAM. The key technique used for fast booting is write-tracking. Write-tracking is used to detect and manage modified data detection and involves setting the kernel region to read-only. This setting is used to trigger intentional faults upon modification requests. As the fault handler can detect the faulting address, write-tracking makes use of the address to manage the modified data. In particular, in our case, we make use of the MMU (Memory Management Unit) translation table. When a write occurs to the boot completed state, write-tracking preserves the original state of the modified address of the kernel region to a particular location, and execution continues. Upon booting, the fast booting process restores the preserved data to the original kernel region allowing rapid system boot-up. We develop the fast booting technique in an actual embedded board equipped with new memory. The boot time is reduced to less than half a second compared to around 15 seconds that is required for the original system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.50-61
• /
• 2018

A precedent defense project study was carried out in the early stage of the project to support efficient determination of the acquisition method of the determined weapons system. A precedent study in the early stage of the project has been neglected, but lack of performance and increased costs are continuing problems. In a precedent study on a number of items within a limited time frame, expected risks during project implementation were not identified and reduced by failing to review the key review element in depth. Therefore, in this paper, we studied the application of the FTA/FMEA technique used in the system safety analysis process to identify key factors to be considered when carrying out the defense research project. The methodology for the development of the key review items was established through the improvement of the FTA/FMEA technique in order to meet specific conditions and given conditions. Based on the results of this study, we redefined core key factors in the precedent study stage, thereby eliminating unnecessary and anticipated risks that may arise in the future project management aspects of the defense project. It is anticipated that this will reduce costs and time in terms of the lifecycle of the weapon system and promote stable operation of the project through reduction of risk.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.28-28
• /
• 2011

우리나라의 주력산업인 반도체 및 디스플레이의 경우 그 생산 설비의 1/3이상이 진공 장비이며 진공 공정을 통해 만들어진다. 이들 산업 분야에서는 우리나라가 세계 최고의 생산 기술을 가지고 있으므로 자체적인 기술 개발 확보가 중요하다. 최근에는 기존에 개발되어 있는 장비의 성능을 뛰어넘어야 하는 공정 기술력이 요구되면서, 진공 공정 기술 개발이 매우 중요한 이슈가 되었다. 반도체나 디스플레이 산업 등 기존 주력산업의 전후방 산업의 경쟁력 강화 측면에서뿐 아니라 태양전지, LED 등 진공기술을 이용한 신성장 동력 산업의 생산 시스템 경쟁력 확보 측면에서도 진공 공정 기술 개발 중요성은 매우 크다. 지금까지 양산에 적용되는 증착, 식각, 확산 등 진공 공정 운영은, 사전 시험을 통해 얻은 최적 공정의 입력 파라미터들을 정해 놓고 그대로 공정을 진행한 뒤, 생산되어 나오는 제품의 상태를 사후 측정하여 공정 이상 여부를 점검하고 미세 조정하는 형태로 진행되고 있다. 실질적으로 현재 진행 중인 진공 공정에 대한 직접적인 정보가 없으므로 공정 중 발생되는 문제들에 대한 대처는 그 공정이 끝난 후에 이루어지는 상황이다. 공정 미세화 및 대구경화에 따라 기존의 wafer to wafer 제어 개념 보다 발전된 개념으로 센서 기반 실시간 공정 진단 제어 기술의 필요성이 대두되었으며 이를 위한 오류 인식 및 예지기술 (Fault Detection & Classification, FDC) 그리고 이 정보를 이용한 첨단 제어 기술(Advanced Process Control, APC)을 개발하는 노력들이 시작되었다. 한국표준과학연구원에서는 수요기업인 대기업과 장비업체, 센서 개발 중소기업 및 학교 연구소와 공동으로 진공 공정 실시간 측정 진단 제어와 관련된 연구를 하고 있다. 진공 공정 환경측정 기술, 플라즈마 상태 측정 기술, 진공 공정 중 발생하는 오염입자 측정 원천 기술 개발과 이를 구현하기 위한 센서 개발, 화학 증착 소스 및 진공 공정 부품용 소재에 대한 평가 플랫폼 구축, 배기 시스템 진단기술 개발 등 현재 진행되고 있는 기술 개발 내용과 동향을 소개한다. 진공 공정 실시간 측정 기술이 확보되면 차세대 반도체 제작에 필요한 정밀 공정 제어가 가능해지고, 공정 이상에 바로 대응 혹은 예방 할 수 있으며, 여유분으로 필요 이상으로 투입되던 자원(대기시간, 투입 재료, 대체용 장비)을 절감하는 등 생산성을 향상을 기대할 수 있다. 또한 진공 환경에서 이루어지는 박막 증착, 식각 공정 과정에 대한 이해가 높아지고, 공정을 개발하고 최적화하는데 유용한 정보를 제공할 수 있으므로, 기존 장비와 차별화된 경쟁력을 가진 고품위 진공 장비 및 부품 개발에 기여할 수 있을 것으로 기대하고 있다.