• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.725-728
• /
• 2001

We have fabricated thin films using the DC/RF magnetron sputtering of 74wt%Ni-l8wt%Cr-4wt%Al-4wt%Cu alloy target and studied the effect of the process parameters on the electrical properties for low TCR(Temperature Coefficient of Resistance) films. In sputtering process, pressure, power and substrate temperature, are varied as controllable parameter. The films are annealed to 400$^{\circ}C$ in air and nitrogen atmosphere. The sheet resistance, TCR of the films increases with increasing annealing temperature. It abruptly increased as annealing temperature increased over 300$^{\circ}C$ in air atmosphere. From XRD, it is found that these results are due to the existence of NiO on film surface formed by annealing. As a results of them, TCR can be controlled by variation of sputter process parameter and annealing of thin film.

• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.153-156
• /
• 1999

The technique is reported of identifying parameters in off-line process. The technique demands that closed-loop system consists of a reference and two-degree-of-freedom controllers (TDFC) in real process. A model process is the same as the real process except their parameters. Deviations are differences between the reference and the output of the plant or the model. The technique is based on minimizing identification error between the two deviations. The parameter differences between the plant and the model are characterized of mean value and of variance which are derived from the identification error. Consequently, the algorithm which identifies the unknown plant parameters is shown by minimizing the mean value and the variance, respectively, within double convergence loops. The technique is applied to course change of a ship. The plant deviation at the first trial is shown to occur in replacing the nominal parameters by the default parameters. The plant deviation at the second trial is shown to not occur in replacing the nominal parameters by the identified parameters. Hence, the identification technique is confirmed to be feasible in the real field.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.2
• /
• pp.81-86
• /
• 2016

Moisture vapor transmission rate (MVTR) is an important item for many applications of polymer breathable thin film. To determine the optimum values of the process parameters, it is essential to find their influence on The significance of six important process parameters namely, extruder cylinder temperature, extruder speed, extruder dies temperature, cooling roll temperature, stretching ratio, stretching roll temperature on breathable film strength of polymer extrusion was determined. Moreover, this paper presents the application of Taguchi method and analysis of variance (ANOVA) for maximization of the breathable film MVTR influenced by extrusion parameters. The optimum parameter combination of extrusion process was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that extruder speed and stretching ratio were the most influential factor on the film strength, respectively. The best results of film MVTR were obtained at higher extruder speed and stretching ratio.

• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.143-149
• /
• 2017

Purpose: In recent years, weight reduction for improving fuel efficiency of the vehicle and cost reduction have been developed. The structure of suspension link is widely used as a single plate press structure which can reduce process and weight compared to existing pipe welding method. However, it was found that the lifetime of a single plate press structure is determined by initial defects that occurred during initial manufacturing rather than fatigue damage caused by driving. Methods: I research the mechanism of failure phenomenon of the single plate press assist arm of rear wheel. In addition, I investigate durability effect parameters to determine the link lifetime in inserting bush into single plate press process through durability test. Conclusion: I discover significant durability effect parameter in inserting bush into single plate press process. It is expected that the durability can be improved by suggesting a bush inserting process inspection guide for similar suspension link like single plate press structure.

• Korean Journal of Chemical Engineering
• /
• v.36 no.3
• /
• pp.356-367
• /
• 2019

This work presents an advanced and systematic approach to analytically design the optimal parameters of a two parameter second-order internal model control (IMC) filter that satisfies operational constraints on the output process, the manipulated variable as well as rate of change of the manipulated variable, for a first-order plus dead time (FOPDT) process. The IMC parameters are designed to minimize a control objective function composed of the weighted sum of the error between the process variable and the set point, and the rate of change of the manipulated variable, and to satisfy the desired constraints. The feasible region of the constrained IMC control parameters was graphically analyzed, as the process parameters and the constraints varied. The resulting constrained IMC control parameters were also used to find the corresponding industrial proportional-integral controller parameters of a Smith predictor structure.

• International Journal of Reliability and Applications
• /
• v.14 no.2
• /
• pp.55-70
• /
• 2013

This paper deals with the Bayesian analysis of the failure data of a repairable mechanical system subject to minimal repairs and periodic overhauls. The effect of overhauls on the reliability of the system is modeled by a proportional age reduction model and the failure process between two successive overhauls is assumed to be 2-parameter Engelhardt-Bain process (2-EBP). Power Law Process (PLP) model has a disadvantage which 2-EBP can overcome. On the basis of the observed data and of a number of suitable prior densities, point and interval estimation of model parameters, as well as quantities of relevant interest are found. Also hypothesis tests on the effectiveness of performed overhauls have been developed using Bayes factor. Sensitivity analysis of improvement parameter is carried out. Finally, a numerical application is used to illustrate the proposed method.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1987.11a
• /
• pp.82-85
• /
• 1987

Preliminary results of using the LPC parameter for text-independent speaker identification problem are presented. The idetification process includes log likelihood ratio for distance measure and dynamic programming for time normalization. To generate the data base for experiments, ten times. Experimental results show 99.4% of identification accuracy, incorrect identification were made when the speaker uses a dialect.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10a
• /
• pp.721-723
• /
• 1987

An Adaptation algorithm is presented and a convergence criterion is derived for parallel model reference adaptive bilinear systems. The output error converges asymptotically to zero, and the parameter estimates are bounded for stable reference models. The convergence criterion depends only upon the input sequence and a priori estimates of the maximum parameter values.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.199-206
• /
• 2005

Mask manufacturing is a high COC and COO process in developing of semiconductor devices because of mask production tool with high resolution. Direct writing has been thought to be the one of the patterning method to cope with development or small-lot production of the device. This study consists two categories. One is the additional process of the direct and maskless patterning generation using SLA for easy and convenient application and the other is a removal process using wet-etching process. In this study, cured status of epoxy pattern is most important parameter because of the beer-lambert law according to the diffusion of UV light. In order to improve the contact force between patterns and substrate, prime process was performed and to remove the semi-cured resin which makes a bad effects to the pattern, spin cleaning process using TPM was also performed. At a removal process, contact force between photo-curable resin as an etching mask and Si wafer is important parameter.

• Journal of the Korean Mathematical Society
• /
• v.36 no.4
• /
• pp.679-679
• /
• 1999