• Korean Journal of Materials Research
• /
• v.27 no.5
• /
• pp.281-288
• /
• 2017

In this study, Fe-Ni slag, converter slag and dephosphorization slag generated from the steel industry, and fly ash or bottom ash from a power plant, were mixed at an appropriate mixing ratio and melted in a melting furnace in a mass-production process for glass ceramics. Then, glass-ceramic products, having a basalt composition with $SiO_2$, $Al_2O_3$, CaO, MgO, and $Fe_2O_3$ components, were fabricated through casting and heat treatment process. Comparison was made of the samples before and after the modification of the process conditions. Glass-ceramic samples before and after the process modification were similar in chemical composition, but $Al_2O_3$ and $Na_2O$ contents were slightly higher in the samples before the modification. Before and after the process modification, it was confirmed that the sample had a melting temperature below $1250^{\circ}C$, and that pyroxene and diopside are the primary phases of the product. The crystallization temperature in the sample after modification was found to be higher than that in the sample before modification. The activation energy for crystallization was evaluated and found to be 467 kJ/mol for the sample before the process modification, and 337 kJ/mol for the sample after the process modification. The degree of crystallinity was evaluated and found to be 82 % before the process change and 87 % after the process change. Mechanical properties such as compressive strength and bending strength were evaluated and found to be excellent for the sample after process modification. In conclusion, the samples after the process modification were evaluated and found to have superior characteristics compared to those before the modification.

• Korean Institute of Interior Design Journal
• /
• v.27 no.2
• /
• pp.24-36
• /
• 2018

Implementing a home modification to enable elderly's safe and independent living is the key plan to realize their aging in place. South Korea in which had entered an aged society is not yet vitalized in home modification for the elderly compared to that of welfare-developed countries, and South Korea provides support that is limited to the low-income elderly. Therefore, this purpose of this study was to analyze the laws related to the home modification, the present condition of home modification support, the standards and guidelines in home modification, the support in house modification cost, and supporting organization and working force in the home modification. Through the analyzing process, this study examined the current situation and problems of institutional support in the home modification for elderly and the proposed plan for institutional improvement. The suggestions based on the results are as in the following. 1) Home modification support law(act or regulation) is required to be improved 2) Home modification support system correspondent to aging process should be provided regardless of their income levels. 3) Delicate plan standard and guideline are necessary for a process of implementing the home modification for the elderly. 4) Information on life behavior is in need for the implementation of elderly-customized home modification. 5) Cost for the home modification should be considered to cover by the Act on Long-Term Care Insurance for the Aged. 6) Housing Welfare Center and Housing Welfare Professional should be actively utilized for the home modification support institution and work force.

• Korean Institute of Interior Design Journal
• /
• v.27 no.2
• /
• pp.55-67
• /
• 2018

There is a growing interest on and expansion of rights of people with disabilities. Among them, people with visual impairment show high adaptation to environments in comparison to people with other types of disabilities, thus a large percentage of them live in their own houses rather than residing in a care facility. According to the housing status of people with visual impairment, the ratio of their residence in rural areas is high. In rural areas people who have disabilities often live in poor residential environments, requiring much improvement. However, such improvement is too costly for them to pay, and home modification that does not fully consider the user, may cause less efficiency and another dangerous situation to people with disabilities. The purpose of this study is to delineate empirical lessons for direction of customized home modification for people with disabilities through analysis of process of home modification including the execution as a intervention. This study used qualitative method to examine and analyzed the entire customized home modification process. The conclusion of this study is as follows. First, home modification measures should be derived considering the suitability of the target building for the specific condition of residents. Second, discussions with various stakeholders from the early stage during which proper home modification measure is searched are essential for realizing appropriate customized home modification. This study has significance in that it provides the direction for customized home modification for people with disabilities as well as empirical data that could reduce trials and errors in the future.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.38-43
• /
• 2011

Industrial reducer is in general use to Deck Crane. High-precision and high-efficient reducer is minimized the power-loss and energy-loss of a machine. So it contribute the price reduction and life extension. Reducer is usually using the Planetary gear reducer. Planetary gear reducer is composed the sun gear, planet gear, internal gear and casing. Industrial reducer's wear and breakage have a short-life. To solve this problem, it is using the profile-shifted-gear or tooth modification. This study was carried out the effect of addendum modification coefficient on tooth fillet bending strength to planetary reducer. Tooth fillet bending stress is calculate. And all parameter were expressed the function of addendum modification coefficient. And then stress concentration factor of tooth fillet curve was express the function of addendum modification coefficient using comparison between theory and finite element analysis.

• Journal of the Korean Society of Safety
• /
• v.31 no.1
• /
• pp.66-73
• /
• 2016

Lyocell fibers were used as a precursor in order to improve yield and strength of cellulose-based precursor while manufacturing activated carbon fiber(ACF). Lyocell fibers as a precursor for the preparation of ACF were surface-modified by reaction with 3-aminopropyltriethoxysilane(APTES) and pre-treated with KOH and H3PO4. Using aforementioned precursor, ACFs were prepared by a series of stabilization, carbonization and activation process at high temperatures. On each process, FT-IR, TGA, UTM and SEM were used to observe fibers' physical properties including structure and porous surfaces. FT-IR results proved that surface modification was achieved during stabilization, carbonization and activation process. TGA results during carbonization process found that surface modified fibers with APTES 0.02 mol(A2) showed higher thermostability, and extended pre-treatment increased yield. Especially, yield was found to have an increase of 10~20 wt% with surface modification during activation process. UTM results showed that tensile strength has the same order of concentration of APTES after surface modification, however, was found to show lower tensile strength than lyocell fibers after stabilization process. SEM results revealed that more homogeneous porosity control could be proceed after modifying the surface for the effective removal of hazardous substances.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.42-47
• /
• 2012

Construction equipment is heavily loaded during normal operation. In recent years, there is a trend that lower gear noise levels are demanded for drivers to avoid annoyance and fatigue during operation. For articulated hauler's final drive, meshing transmission error(T.E.) is the excitation that leads the tonal noise known as gear whine, and radiated gear whine is also the dominant source of noise in the whole gearbox. This paper presents a method for the analysis of the tooth profile modification, and the prediction of transmission error under the loaded torques for the spur gear pair of the articulated hauler's final drive. And the transmission error, transmission error harmonics and contact stress are also calculated and compared before and after tooth modification under one torque. The simulation result shows that the transmission error and contact stress under the loads can be minimized by the appropriate tooth profile modification.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.5
• /
• pp.40-49
• /
• 2010

Conical involute gears are being used for marine gearboxes, automotive transmissions, and robots, and so on, but not much. As involute profile gear, conical involute gear not only can be engaged with spur and helical gear but also can be used for power transmission of parallel, crossed and skewed axis with small angle. Hence, conical involute gears are likely to develop in future. Through a study on the basic theory of conical involute gear, tooth surface compressive stress analysis was performed by using commercial modeling program, comparing before and after profile modification. As a result, it noticed that tooth profile modification is able to relieve more tooth surface compressive stress than before modification.

• Genomics & Informatics
• /
• v.12 no.2
• /
• pp.71-75
• /
• 2014

The tRNA structure contains conserved modifications that are responsible for its stability and are involved in the initiation and accuracy of the translation process. tRNA modification enzymes are prevalent in bacteria, archaea, and eukaryotes. tRNA Gm18 methyltransferase (TrmH) and tRNA $m^1G37$ methyltransferase (TrmD) are prevalent and essential enzymes in bacterial populations. TrmH involves itself in methylation process at the 2'-OH group of ribose at the 18th position of guanosine (G) in tRNAs. TrmD methylates the G residue next to the anticodon in selected tRNA subsets. Initially, $m^1G37$ modification was reported to take place on three conserved tRNA subsets ($tRNA^{Arg}$, $tRNA^{Leu}$, $tRNA^{Pro}$); later on, few archaea and eukaryotes organisms revealed that other tRNAs also have the $m^1G37$ modification. The present study reveals Gm18, $m^1G37$ modification, and positions of $m^1G$ that take place next to the anticodon in tRNA sequences. We selected extremophile organisms and attempted to retrieve the $m^1G$ and Gm18 modification bases in tRNA sequences. Results showed that the Gm18 modification G residue occurs in all tRNA subsets except three tRNAs ($tRNA^{Met}$, $tRNA^{Pro}$, $tRNA^{Val}$). Whereas the $m^1G37$ modification base G is formed only on $tRNA^{Arg}$, $tRNA^{Leu}$, $tRNA^{Pro}$, and $tRNA^{His}$, the rest of the tRNAs contain adenine (A) next to the anticodon. Thus, we hypothesize that Gm18 modification and $m^1G$ modification occur irrespective of a G residue in tRNAs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.105-108
• /
• 2000

Finite element analysis of a multi-stage deep drawing process is carried out for the die design of rectangular cup drawing with the large aspect ratio. Simulation is performed for thorough investigation of unfavorable mechanisms in the initial design. The analysis reveals that the difference of the drawing ratio and the irregular contact condition produces non-uniform metal flow to cause wrinkling and severe extension. In this paper, the modification guideline is proposed in the design of the process and the tool shape. The analysis result confirms that the modified design not only improves the quality of a deep-drawn product but also reduces the possibility of failure.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1305-1314
• /
• 2023

The global ship repair and modification market is expected to grow up to approximately $ 30 billion by 2025. Korea's shipbuilding industry is leading the world grounded on its international competitiveness in design and production technology. The reality, however, is that the ship repair and modification industry is centered on Gyeongnam, and there are only two to three ship repair workplaces that can repair large ships. Therefore, domestic ship repair companies target small and medium-sized ships mainly. This is because there are few workplaces equipped with a large dock in which large ships like LNG ships can be inspected regularly or repaired, complaints are severe for environmental problems, and related environmental regulations are so strict that it is very hard to obtain government approval for the extension of ship repair and modification workplaces or the opening of new shipbuilding sites. Besides, on account of the workers' high wages, few experts related, and higher ship repair price compared to that of Southeast Asia, most of the volume of repairing large ships including domestic LNG ships is being lost to Southeast Asian or Chinese markets. In this study, the work process and pre-work preparation process for ship hull (winch, windlass, hatch cover, ramp door, cargo gear, anchor chain) repair were analyzed and presented to foster domestic ship repair experts and revitalize related industries.