• 한국표면공학회지
• /
• 제42권6호
• /
• pp.294-300
• /
• 2009

The Friction Stir Welding (FSW) has mainly been used for making butt joints in Al alloys. The development of Friction Stir Lap Welding (FSLW) would expand the number of applications. In this study, for effective application on thin aluminum alloy lap joint, non-heat treatment A5052 alloys were joined by FSLW with the length of probe 2.3 mm and 3.0 mm. Investigating the characteristics of joint area showed the results were as below ; When the length of probe was 2.3 mm, good joint area was formed at all welding condition except for 600 rpm-700 mm/min. In the case of 3.0 mm probe length, there was formed good joint area without defects at 1500 rpm-100 mm/min. The width of joint area, position and size of defects were very important factors for FSLW, due to heat input and stirring intensity.

• 한국표면공학회지
• /
• 제45권5호
• /
• pp.181-187
• /
• 2012

The Friction Stir Welding (FSW) has mainly been used for making butt joints in Al alloys. The development of Friction Stir Lap Welding (FSLW) would expand the number of applications. In this study, microstructures and mechanical properties of FSLW in A5052 alloy were investigated under varying rotating speed and probe length. Investigating the characteristics as FSLWed conditions were as below ; Failure Maximum load by shear fracture was increased proportional to the width of joint area, which was increased by input heat, stirring intensity in the case of 2.3 mm probe length. Tensile fracture occurred, and maximum load was determined due to side worm hole of joint area and softening of microstructure in the case of 3.0 mm probe length. In the case of 3.7 mm probe length, material hook and bottom worm hole were appeared at the end interface of joint area. The most sound FSLW condition with no defects was 3.0 mm probe length and 1500 rpm-100 mm/min. No defects were showed in 1500 rpm-100 mm/min and 1800 rpm-100 mm/min, but Vickers microhardness distribution in TMAZ/HAZ which was fracture zone was lower in 1800 rpm-100 mm/min than in 1500 rpm-100 mm/min. In this condition highest tensile strength, 215 MPa (allowable rate 78% of joint efficient) was obtained.

• 미생물학회지
• /
• 제29권3호
• /
• pp.189-194
• /
• 1991

The degree of the genetic variations among Clostridium thermocellum ATCC 27405 and the wild type strains was investigated by the mehtod of GC ratio, DNA-DNA hybridization and RFLP (Restriction Fragment Length Polymorphism) patterns by ribosomal RNA and M13 probe. GC ratio and KNA homology values of th three isolates were approximately equal to those of ATCC type strain. The RFLP patterns by the rRNA and M13 probe showed some differences among C. thermocellum ATCC 27405, wild type strains and Clostridium thermohydrosulfuricum ATCC 33223, indicating that the two probes can be useful in subspecies- and apecies-identification.

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.167-171
• /
• 2004

In this paper, we proposed a new method to control the length of carbon nanotube using electrochemical etching. We made a nano probe that was composed of the tungsten tip and multi-wall carbon nanotube. The nano probe was placed on the nano stage and the carbon nanotube on the nano probe was etched in the electrolyte solution with the applied voltage. The overall procedures were done under optical microscope and can be monitored. We can obtain a nano probe with proper length through this procedure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.449-450
• /
• 2008

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1888-1891
• /
• 2003

In this paper, we proposed a new method to control the length of carbon nano tube in the single CNT probe. A single CNT probe was composed of a tungsten tip made by the electrochemical etching and carbon nano tube which was grown by CVD and prepared through the sonication. The two components were attached with the carbon tape. Since the length of CNT can not be controlled during the manufacturing, the post process is needed to shorten the CNT. In this paper, we proposed the method of electrochemical process. The process was done under the optical microscope and the results were checked by SEM. The diameter of the carbon nano tube used in this paper was about 130nm because the above process had to be done with the optical microscope. Using the method proposed in this paper, we can control the length of the nano tube tip.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.576-576
• /
• 2013

Recently, diagnostics of plasma becomes more important due to requirement of precise control of plasma processing based on measurement of plasma characteristics. The Langmuir probe has been used for the diagnostics but it has an inevitable uncertainty and error sources such as incorrect tip length and RF noise. Instead of the Langmuir probe, various diagnostic methods have been developed and researched. The cutoff probe is promising one for plasma density using microwaves and resonance phenomenon at the plasma frequency. The cutoff probe has various advantages as follows; (i) it is simple and robust, (ii) it uses few assumptions, and (iii) it is free from deposition by reactive gas. However, the cutoff probe also has uncertainty and error sources such as gap between tips, tip length, direction of tip plane, and RF noise. In this study, the uncertainty and error sources in manufacturing both probes and in diagnostics process were analyzed via comparative experiment at various discharge conditions. Furthermore, to reveal the user dependence of both probes, three well trained Ph. D students made the Langmuir probe and the cutoff probe, respectively, and it were analyzed. Thought this study, it is established that reliability and validity of the Langmuir probe and the cutoff probe related with not only the intrinsic characteristics of probes but also probe user.

• 전자공학회논문지SC
• /
• 제45권6호
• /
• pp.16-25
• /
• 2008

미세 탐침이란 프로브 카드(Probe Card)를 구성하는 초미세탐침을 의미한다. 이러한 미세 탐침은 그 크기가 상당히 미세하기 때문에 외관 이상 유무를 사람의 눈으로 검사하기가 상당히 어렵다. 반면, 프로브카드를 구성하는 미세 탐침의 이상 유무는 상당히 중요한 요소라고 볼 수 있다. 이에 본 연구에서는 사람의 눈으로 검사하기 어려운 미세 탐침의 불량 상태를 자동화된 비전 시스템으로 검사할 수 있는 방법을 개발하였다. 즉 탐침의 구부러진 각도, Tip Length, 종단 직경을 고속으로 자동 검사할 수 있는 비전 기술을 개발한 것이다 제안한 방법에 의한 실험결과, 사람의 육안에 위한 검사보다 검사의 정확도와 속도가 향상되었으며, 또한 조명환경에 대해서도 강건성(robustness)이 향상되었음을 알 수 있었다.

• 대한토목학회논문집
• /
• 제41권2호
• /
• pp.133-141
• /
• 2021

프로브 차량 데이터로부터 전수화 된 교통량, 밀도, 대기행렬 길이를 추정하기 위해 프로브 차량 비율이 필요하다. 이를 위해 기존 연구는 프로브차량과 일반 차량의 위치에 대한 확률구조를 활용하여 지점 검지기 없이 프로브 차량 비율을 추정하는 방법을 제시하였으나, 기존 연구의 방법론은 다차로 도로에 적용할 수 없다는 한계가 있었다. 따라서 본 연구는 각 차로의 대기행렬 길이에 확률분포를 도입함으로써 다차로 접근로에서 프로브 차량 비율을 추정하고자 하였다. 사례연구 결과, 추정치와 관측치 간 이격이 있었으나, 추정치가 관측치의 경향을 따라가는 것으로 나타났으며, 향후 보정계수 도입 등을 통하여 추정치를 개선할 여지가 있었다. 본 연구는 지점 검지기가 없는 다차로 접근로에서 전수화 된 교통량, 밀도, 대기행렬 길이를 추정하기 위한 기초연구로서 활용될 것으로 기대된다.

• 한국수정란이식학회지
• /
• 제12권2호
• /
• pp.203-209
• /
• 1997

This study was carried out to compare the actual size(length and height) of ovaries, follicles and corpora lutea of Korean native cow with those on sonograms. We used 3 different probes(3.5 MHz abdominal probe, 6.5 MHz transvaginal probe and 5.0 MHz transrectal probe) and a calipher for measurements of ovaries, follicles and corpora lutea on sonograms and actual size. Under water immersion, 157 ovaries were scanned with 3 probes and measured in actual size and compared each other. The average height and width of ovaries of Korean native cows were 17.40$\pm$3.99 and 34.23$\pm$6.02mm, respectively. In comparison of height, length of ovaries and preovulation follicles, we found that image with a transvaginal probe was nearly the same as the actual size(p<0.01), but with an abdominal probe the image was appeared larger than the actual size. In measurement(diameter) of preovulation follicles the transvaginal probe was proven to be more accurate to the actual size than other probes and in corpus luteum measurement all probes were accurate. In the comparison of number of follicles by different size ranges, there was no statistical difference in the count of follicles over 10 mm in diameter between the transvaginal probe and naked eyes.