• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.521-524
• /
• 2008

Effect of prior deformation on the sliding wear of the ultra-fine grained (UFG) ferrite-martensite dual phase (DP) steel was investigated. The UFG DP steel was fabricated by the ECAP and subsequent intercritical annealing. The steel was cold rolled before the wear test, and the effect of the prior deformation on the wear was examined. The wear tests were carried out at various loads against a bearing steel ball. The wear rate of the UFG DP steel that did not experience the prior deformation was higher than that of the coarse-grained (CG) DP steel, because of more severe surface shear deformation. The wear rate of the specimens with prior deformation was much higher than that of the specimen without prior deformation. The deformed CG DP specimen showed higher rate than the deformed UFG DP specimen, and the rate-variation of the CG DP steel was much bigger under the same test condition.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.4
• /
• pp.1-9
• /
• 1990

In this study, the ausformed martensite cooled to $-196^{\circ}C$ with various deformation degrees in Fe-30%Ni-0.24%C alloy was transformed to reversed austenite at $500^{\circ}C$ by cyclic reverse martensitic transformation. The effects of prior deformation and the number of cyclic reverse transformation on the microstructure and the mechanical properities of reversed anstensite were investigated. Experimental results showed that the strength of reversed austenite was higher than that of original austenite. This is due to higher dislocation density and grain refining. The reversed austenite formed from ausformed martensite was highly strengthened by prior deformation. This strengthening effect of reversed austenite is attributed to higher dislocation density than grain fefining. The yield strength of reversed austenite below 30% prior deformation, but above 30% prior deformation the strength of reversed austenite is lower than that of deformed austenite. This is due to partly disappearance of strain hardening effect at higher deformation degree by reverse transformation. The strength of reversed austenite is increased with the number of cyclic transformation. Especially, it is principally strengthened by the first cyclic transformation and shows higher increase in yield strength than that of ultimate tensile strength.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.4
• /
• pp.41-52
• /
• 1990

This research has been performed in order to investigate the effect of prior deformation on the Ms temperature and reversed As of Fe-Ni alloy. The Ms temperature rose with increment of strain to 30% but lowered over 50%. It can be analysed that martensitic transformation was promoted by partial dislocation in low strain, but suppressed by dislocation cell structures in high strain. The As temperature was substantially increased with higher deformation to 20% but slowly above 50%. It may be caused that as the transition bands formed by deformation constrained shear strain, therefore austenitic transformation was hindered.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.1
• /
• pp.26-36
• /
• 1993

In this study, the ausformed martensite and marformed martensite obtained from austenite with various deformation degrees in Fe-31% Ni-0.2%C alloy were transformed to revesed austenite at $510^{\circ}C$ by cyclic reverse martensite transformation. The effect of prior deformation, the rapid heating rate of reversion and number of cyclic transformation on the microstructure, mechanical properties of reversed austenite were investigated. The reverse austenite transformation is accomplised by the mechanism of shear type transformation. The structure of reversed austenite formed from ausformed martensite and marformed martensite with high deformation degrees is a fine structure of nearly equiaed grain containg a high density of dislocation tangles and was largely affected by the prior deformation applied before reversal transformation. The strength of reversed austenite is more increased with of cyclic transformation especially it is strength at the first cyclic transformation. The yield stress of revesed austenite of ausformed martensite is lower than that of marformed martensite.

• Korean Journal of Metals and Materials
• /
• v.47 no.11
• /
• pp.759-772
• /
• 2009

Amorphous alloys, in addition to being promising materials for a variety of practical applications, provide an excellent test bed for evaluating our understanding of the underlying physics on deformation in amorphous solids. Like many amorphous materials, amorphous alloys can exhibit either homogeneous or inhomogeneous deformation depending on the stress level. The mode of deformation has a strong influence on whether the material behavior is classified as ductile or brittle. It was observed that the characteristics of these deformations are largely dependent on the atomic-scale structures of the alloys and determine the amount of the plastic deformation prior to failure. In this study, the structural features that control the homogeneous deformation of amorphous alloys are outlined on the basis on experiments and molecular dynamics simulations.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.177-184
• /
• 2000

In this work, some inaccuracies and limitation of prior indentation theory, which is based on the deformation theory of plasticity and experimental observations, are first investigated. Then effects of major material properties on the configuration of indentation load-deflection curve are examined via incremental plasticity theory based finite element analyses. It is confirmed that subindenter deformation and stress-strain distribution from the deformation theory of plasticity are quite dissimilar to those from incremental theory of plasticity. We finally suggest the optimal data acquisition location, where the strain gradient is the least and the effect of friction is negligible. This data acquisition point increases the strain range by a factor of five.

• Transactions of Materials Processing
• /
• v.25 no.4
• /
• pp.254-260
• /
• 2016

In this study, hot isostatic pressed Ni-base superalloy was subjected by high-pressure torsion process to improve the dispersion of gamma prime phase, mechanical properties and remove prior particle boundaries. The resulting microstructural size decreases and prior particle boundaries removed with increasing strain by high-pressure torsion process. Moreover, the microhardness values and room temperature tensile strength were enhanced. However, the tensile elongation was decreased as increasing strain due to fast crack propagation along the refined and well dispersed gamma prime particles.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.260-261
• /
• 2006

The behaviour of steel powder compacts during sintering has been investigated by dilatometry and X-ray computed microtomography. Dilatometry measurements showed that the anisotropic deformation results from various phenomena arising at different moments of the cycle including the delubrication stage. Microtomography provided 3D images of the microstructure induced by prior die pressing and its changes throughout sintering. Finally a schematic description of the main phenomena responsible for the deformation of metal powder compacts during sintering is proposed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.169-176
• /
• 2018

Removal of angular deformation induced during the welding of butt joints in thick steel plates needs expert skill and is costly. To reduce deformation, proper joint designs are studied with a prediction of deformation prior to welding. However, as the thickness of a plate increases, a predictive analysis of the welding process is more difficult, especially if there is an increase in the number of welding passes in the joint. In this study, a numerical model with the finite element method (FEM) was developed to analyze the angular deformation in the multi-pass welding of butt joints of plates made of AH32 steel that had a thickness of up to 100 mm. A series of numerical simulations were then performed based on the developed model to predict the deformations for thick plates. With the results obtained by the analyses, this study suggested optimal X-shape grooves for the butt joints of thick plates to minimize the angular deformation. As the thickness of the plate increased to 100 mm, the ratio of the depth of the front-side groove to that of the back-side groove should be gradually increased to nearly 1:3.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.4
• /
• pp.32-37
• /
• 2010

One of the most common engineering processes using plastics is the injection molding. In addition, plastics are utilized over the entire areas in our life including cars and home appliances among others for their characteristics with no deterioration even after a long time, as well as for their light weights in addition to their good durability. This paper aimed to minimize defects through prior analyses on the weld line, air traps, filling time, molding temperature and deformation patterns among others while carrying out interpretations on the cooling, filling and deformation in the injection process using the moldflow for rear lamp reflectors among components for a car in making parts through the coating process after injection.