• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.120-125
• /
• 2002

AC powder EL devices were fabricated by screen printing method with the dielectric materials in insulating layer and the electrical resistivity of rear electrode. Brightness and current density were measured at voltage range of 50∼300 $V_{rms}$ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Brightness and current density were measured by luminometer and multimeter. Also, dielectric constant for dielectric layer was measured by impedance analyser after preparing thick film. Dielectric constant was improved with amount of $TiO_2$ to $BaTiO_3$ powder. By applying such a process to dielectric layer of low cost AC powder EL device, brightness was improved to 50 cd/$m^2$ at similar current density. Dielectric constant $BaTiO_3$ powder by solution combustion process is better than commercial $BaTiO_3$ powder. By applying to that of low power consumption AC powder EL device, brightness was improved to 85 cd/$m^2$. Brightness of AC powder EL device was relatively decreased by control of electrical resistivity of rear electrode, current density was also decreased.

• Information Systems Review
• /
• v.9 no.1
• /
• pp.191-214
• /
• 2007

This study analyzes the process of establishing BSC based strategic performance evaluation system of KOMSCO. This case could be a reference to other public institutes for BSC introduction and efficient BSC usage. Internal control system of KOMSCO has been improved by EVA system in 1999, BSC introduction and Job analysis in 2001 through 2002, and BSC performance evaluation system in 2004. KOMSCO tries to reflect BSC concept by inducing employees to cooperate selection process of CSF and KPI and by considering the organizational characteristics of KOMSCO in constructing it's performance indices. It is suggested that these processes are very important and should be followed by other institutes in their BSC introduction. By applying BSC, KOMSCO provides improvement in employees' understanding of strategy, performance management, and performance evaluation. KOMSCO' information system based on ERP and efficiently connected to EIS, KMS, and BSC seems to play an important role of BSC application. BSC system of KOMSCO is now in the early stage of application and needs to be evaluated by the efficiency of usage in terms of overall performance evaluation system, deduction system of evaluation point for excess accomplishment over target, and connection to budget system.

• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.604-608
• /
• 2006

Polymer composites for measuring the radioactive contamination are prepared by coating ZnS(Ag) powders as a scintillator on polysulfone base layer. The composites consist of the active layer for a scintillation reaction with radioactive wastes and the transparent support layer for transmittance of light photons emitted by scintillation in the active layer. The binding of the active layer, including ZnS(Ag), on the support layer is proceeded via coating with polysulfone as a binder, without any extra adhesive. The coating was obtained by either casting via a Doctor Blade as applicator or screen printing. The prepared composites feature a monolithic structure, resulting in the complete adhesion between two layers. The composite prepared by the casting technique using an applicator holds a good detection efficiency in measuring the alpha radionuclide, but its structure becomes fragile because of warping in morphology. On the contrary, the composite prepared by the screen printing shows a good detection capacity as well as a good stability in a mechanical shape.

• Journal of Environmental Impact Assessment
• /
• v.24 no.2
• /
• pp.154-162
• /
• 2015

Correlation between occupational exposure levels to toluene and urinary hippuric acid (HA) concentrations were studied for 124 workers at 54 work places. The highest indoor toluene concentration measured at printing process was 81.116 ppm, and their geometric average concentration was as high as 12.304 ppm. The geometric average concentration of hippuric acid in urine samples from workers who are exposed to toluene was 0.714 g/g creatinine. This is almost five times higher than the average HA concentration from non-exposure workers. Printing workers showed the average HA concentration of 1.145 g/g creatinine from their urine samples. It is the highest concentration among the workers exposed to toluene. The correlation coefficient between HA concentrations in urine and indoor toluene concentration at work places was relatively high as r=0.624 (P<0.01). But the correlations of HA with sex, smoking, drinking, age and employment history was relatively low. We can express the regression equation for the urinary HA concentration which is Y = 0.037X + 0.562 as exposure toluene concentration is X. The urinary HA concentrations showed significantly increase depend on indoor toluene concentration at work place.

• Clean Technology
• /
• v.19 no.4
• /
• pp.410-415
• /
• 2013

The supercapacitors were fabricated using silver (Ag) nano paste and activated carbon paste on the polyimide (PI) film and 5% potassium polyacrylate (PAAK) was used for gel electrolyte. In this paper, the current collector film and the electrode film were fabricated using screen printing. The thickness of printed silver paste was $7.3{\mu}m$ and the sheet resistance has the range of $5-7m{\Omega}/square$. An activated carbon with a surface area of $1,968m^2/g$, an electronic conducting agent (SUPER P, TIMCAL) and poly (4-vinylphenol) were mixed in 2-(2-buthoxyethoxy) ethyl acetate (BCA) with a ratio of 7:1:3 to fabricate the electrode paste. To analyze electrochemical characteristics, cyclic voltammetry was performed to evaluate the stability of the devices under the voltage range of -0.5-0.5 V. The calculated specific capacitances were 44.04 and 8.62 F/g for 10 and 500 mV/s scan rates, respectively.

• Journal of Conservation Science
• /
• v.7 no.2
• /
• pp.80-85
• /
• 1998

The structure, dimensions, condition and other characteristics of the Koryo Buddhist Canon (the Koreana Tripitaka) Printing Wood Blocks stored at the Haein-sa Monastery were surveyed to obtain basic data needed for the conservation of the Wood Blocks. The dimensions of the Wood Blocks Were measured and we could figured out the blueprint designed at the time of the carving the Wood Blocks. The dimensions of the wooden board were as follows: width, 8'chi'('cun' in Chinese, 24 cm);thickness, 1 'chi' (3 cm); length, 2'cha' ('chi' in Chinese) and 3 'chi' (68 cm) or 2 'cha' and 6 'chi' (78 cm). The dimensions of the end pieces were as follows: width, 1 'chi' and 5 'fun' (4.5 cm; thickness, 1 'chi' and 4 'fun' (4 cm); length, 8 'chi' and 2-4 'fun' (24.6-25.2 cm). There were 6 types of metal strips and the length of the nails employed was 1 'chl' (3 cm). Investigation on the differences in the length of the wood Blocks and the shapes of the metal strips will be of interest. Since we surveyed only small portion of the Wood Blocks. the result may be different if entire Wood Blocks were examined. The data acquisition of the entire Wood Blocks will be the basis to the conservation of the Wood Blocks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.319-325
• /
• 2018

The use of 3D printing (Additive Manufacturing) technology has expanded from initial model production to the mass production of parts in the industrial field based on the continuous research and development of materials and process technology. As a representative polymer material for 3D printing, the polyamide-based material, which is one of the high-strength engineering plastics, is used mainly for manufacturing parts for automobiles because of its light weight and durability. In this study, the specimens were fabricated using Selective Laser Sintering, which has excellent mechanical properties, and the flexural characteristics were analyzed according to the temperature of the two types of polyamide 12 and glass bead reinforced PA12 materials. The test specimens were prepared in the directions of $0^{\circ}$, $45^{\circ}$, and $90^{\circ}$ based on the work platform, and then subjected to a flexural test in three test temperature environments of $-25^{\circ}C$, $25^{\circ}C$, and $60^{\circ}C$. As a result, PA12 had the maximum flexural strength in the direction of $90^{\circ}$ at $-25^{\circ}C$ and $0^{\circ}$ at $25^{\circ}C$ and $60^{\circ}C$. The glass bead-reinforced PA12 exhibited maximum flexural strength values at all test temperatures in the $0^{\circ}$ fabrication direction. The tendency of the flexural strength changes of the two materials was different due to the influence of the plane direction of the lamination layer depending on the type of stress generated in the bending test.

• Journal of the Korean Society of Radiology
• /
• v.17 no.7
• /
• pp.1091-1097
• /
• 2023

Bolus is used in radiation therapy to prescribe an even dose to the tumor when the skin surface is inclined or has irregularities. At this time, the dose to the skin surface increases. Due to the patient's unique body structure and irregular skin, voids may occur between the bolus and the skin, which may reduce the accuracy of treatment. Therefore, in this study, the existing bolus and the self-produced bolus through 3D printing were applied to the nasal area, and the difference between the surface dose after treatment plan and the dose directly measured with an Optically Stimulated luminescence(OSL) dosimeter was compared to the existing bolus. The bolus rate was 97%, PLA 100.33%, ePETELA 75A 100.53%, and ePETELA 85A 100.36%. It was confirmed that there was little error in the measurement values and treatment plan values for each material. In addition, compared to when applying a conventional bolus, a difference of -3% to +0.5% for a 3D printed bolus can be confirmed, so a customized bolus produced through 3D printing can complement the shortcomings of the existing bolus. It is believed that there will be.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.20 no.1
• /
• pp.109-124
• /
• 2018

This study focused on the accessory of clothes of minority groups in Yunnan province to further the research about specific accessories' development in the future. Among the minorities in Yunnan, this study centralized characteristics of ornaments, hats and belts among five minority groups such as the Bai, Zhuang, Hani, Dai, and the Zang as representatives to study in detail because these five ethnicities have a relatively long history and plentiful information. The results are as follows: First, exaggeration means large gorgeous patterns that attract attention. Generally, there are many natural resources that can be used in places where these minority groups live such as gems, gold, silver shells and animals' horns, bone, teeth and the like. Headdress includes combs, loops, hairpins and other similar articles. Second, nature is a very fundamental part that people rely on for existence and development. The production and living that people need in life all depend on nature. The design of accessories is made from animal forms and patterns of clothes are presented through embroidery and wax printing. Designers always tried to add natural elements to their works. Third, symbolism consists of two aspects: One is the people's imagination, which related to actual materials, and the other is the product of imagination that provides better conditions to inspire people when they design. In China, most minority groups believe in Buddhism. The symbols in the clothing show their devout faith. Even the method of wear has many special implications like the use of accessories and length of clothing. The pattern of dragons and use of golden, red and other colors all have a proper symbolic significance in modern designs.

• 전자공학회논문지 IE
• /
• v.44 no.2
• /
• pp.26-31
• /
• 2007

A surface treatment was performed after the screen printing of a carbon nanotube paste for obtaining the carbon nanotube field emission array(CNT FEA) on the soda-lime glass substrate. In this experiment, Ar ion bombardment was applied as an effective surface treatment method. After making a cathode electrode on the glass substrate, photo sensitive CNT paste was screen-printed, and then back-side was exposure by uv light. Then, the exposed CNT paste was selectively remained by development. After post-baking, the remained CNT paste was bombarded by accelerated Ar ions for removing some binders and exposing only CNTs. As results, the field emission characteristics were strongly depended on the accelerating energy. At 100 eV, the emission was highest and as the acceleration energy increases more then 100 eV, the emission decreased. This was due to the removal of CNT itself as well as binders.