• Elastomers and Composites
• /
• v.6 no.1
• /
• pp.71-81
• /
• 1971

The intention of this study is to investigate the properties of polymer blend, NBR/PVC vulcanizates and blending procedures such as roll-mixing temperatures and sequences for polymer blending of NBR and PVC(resin type). The results obtained are as follows: 1. The roll temperature applied for polymer blending is around $150^{\circ}C$. At this temperature region, the degradation of rubber stock, which may be caused by heat, can be minimized and mill processing in practical application in industries can also be facilitated. 2. It is obviously necessary that a small amount of plasticizers should be added to the stock for improving processibility of roll mixing and physical properties. 3. On roll-mixing sequence, it is more effective that PVC compounded with plasticizer is added to NBR milled on hot roll. 4. The vulcanizates of the blends with different degree of polymerization of PVC ale similar to one another in properties. 5. NBR/PVC(70/30) blends shows the better physical characters than eve,-made foreign latex blend except abrasion-resistance. 6. As PVC addition ratio is increased, the physical properties such as resistance to ozone, tear, heat and oil and tensile strength, modulus, hardness have also improved, on the other hand, tension set and rebound character decreased. 7. The curve of ultimate elongation have point of inflection at the ratio of $30\sim40$ part of PVC. 8. While CR is blended, the physical properties such as brittle point, rebound and resistance to oil in high temperature have improved. 9. Polymer blend of NBR and domestic PVC is applied for the industrial utility such as rubber sole and heel, electric wire cover and oil-resistant packing, coating and gasket, printing roll, film for food packing etc.

• Journal of the Korean Vacuum Society
• /
• v.20 no.2
• /
• pp.146-154
• /
• 2011

The adhesive-tape of a liquid leak film sensor including the alarm system is developed. The sensing film is composed of three layers such as base film layer, conductive line layer, and protection film layer. The thickness of film is 300~500 um, the width is 3.55 cm, and the unit length is 200 m. On the conductive line layer, three conducting lines and one resistive line are formulated by the electronic printing method with a conducting ink of silver-nano size. When a liquid leaks for the electricity to be conducted between the conductive line and the resistive line, the position of leakage is monitored by measuring the voltage varied according to the change of resistance between two lines. The error range of sensing position of 200 m film sensor is ${\pm}1m$.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.533-538
• /
• 2014

Today, silicon and epoxy resin are used as materials of conversion lenses for white LEDs on the basis of their good bonding and transparency in LED packages. But these materials give rise to long-term performance problems such as reaction with water, yellowing transition, and shrinkage by heat. These problems are major factors underlying performance deterioration of LEDs. In this study, in order to address these problems, we fabricated a conversion lenses using glass, which has good chemical durability and is stable to heat. The fabricated conversion lenses were applied to a remote phosphor type. In this experiment, the conversion lens for white LED was coated on a glass substrate by a screen printing method using paste. The thickness of the coated conversion lens was controlled during 2 or 3 iterations of coating. The conversion lens fabricated under high heat treatment temperature and with a thin coating showed higher luminance efficiency and CCT closer to white light than fabricated lenses under low heat treatment temperature or a thick coating. The conversion lens with $32{\mu}m$ coating thickness showed the best optical properties: the measured values of the CCT, CRI, and luminance efficiency were 4468 K, 68, and 142.22 lm/w in 20 wt% glass frit, 80 wt% phosphor with sintering at $800^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.110-112
• /
• 2006

Membrane electrode assembly (MEA) for polymer electrolyte fuel cell (PEFC) are commonly prepared in the research laboratory by spraying, screen-printing and brushing catalyst slurry onto membrane or other support material like carbon paper or polyimide film in a batch style. These hand applications of the catalyst slurry are painstaking process with respect to precision of catalyst loading and reproducibility. It has been generally mentioned that the adoption of continuous process is very helpful to develop the reliable product. In the present work, we report the results of using continuous type coater with doctor-blade to coat catalyst slurry for preparing the MEA catalyst layers In a faster and highly reproducible fashion. We show that while expectedly faster than batch style, the machine coater requires the use of slurry of appropriate composition and a properly selected transfer decal material in order to achieve superior MEA plat lnw loading reproducibility. To make highly viscous catalyst slurry that is imperative for using coater, we use 40wt.% Nafion solution and minimize the content of organic solvent. And the choice of proper high surface area catalyst is important in the viewpoint of making well-dispersed slurry. After catalyst coating onto the support material, we transferred the catalyst layer to both sides of Nafion membrane by hot-pressing In this case, the degree of transfer was Influenced by hot-pressing condition including temperature, pressure, and time. To compare the transferring ability, we compared so many films and detaching papers. And among the support, polyethylene terephthalate(PET) film shows the prominent result.

• Journal of Fashion Business
• /
• v.12 no.1
• /
• pp.147-163
• /
• 2008

This research aims to develop cultural products for professional sales after producing creative products utilizing dinosaur characters, which are the representative exhibited item of dinosaur-centered museum. There are seven museums in Korea whose theme is dinosaur. There are three dinosaur museums among them, Goseong Dinosaur Museum at Kyungnam, Mokpo Natural History Museum, and Seodaemun Museum of Natural History. While inspecting cultural products within the museum shops of these three museums, general products occupy more than 80% of all the products rather than products related to dinosaurs, and has a problem that most products are decorative ones. This resulted from that enterprises supplying these products are not professional ones and are irrelevent to cultural industry; as result, purpose of conveying culture through products is lost. This research develops dinosaur characters utilizing computer 3D techniques in order to imbue unique characteristics to dinosaur museums and informing cultural speciality of our country. In addition, this research presented design method of cultural products by grafting traditional symbols onto these characters, and actually produced 11 items of 5 kinds: toys(dolls), clothes(T-shirts, pajamas, socks), stationery(notebooks, memo), accessaries (bags, umbrellas, handkerchief), and others(cups). On the items above, dinosaur characters are variously utilized in form of printing, embroidery, and stickers by using computer 3D technique. A cultural product is a tangible form which could show variety of cultural characteristics of our nation that could spread the culture through the consumers, and such type of purchasing could increase values of cultural industry by creating economic profits; such points are the significance of this study.

• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.627-631
• /
• 2005

The $(La_{0.8}Sr_{0.2})_{0.95}MnO_3$/yttria-stabilized zirconia (LSM/YSZ) composites were investigated as anode materials for high temperature steam electrolysis using X-ray diffractometry, scanning electron microscopy, galvanodynamic and galvanostatic polarization method. For this purpose, the LSMperovskites were fabricated in powders by co-precipitation method and then were mixed with 8 mol% YSZ powders in different molar ratios. The LSM/YSZ composites were deposited on 8 mol% YSZ electrolyte disks by means of a screen printing method, followed by sintering at temperatures above $1,100^{\circ}C$. From the experimental results, it is concluded that the electrochemical properties of LSM and the LSM/YSZ composites are closely related to their microstructure and operating temperatures.

• Advances in aircraft and spacecraft science
• /
• v.4 no.3
• /
• pp.281-296
• /
• 2017

The axial-injection end-burning hybrid rocket proposed twenty years ago by the authors recently recaptured the attention of researchers for its virtues such as no ${\zeta}$ (oxidizer to fuel mass ratio) shift during firing and good throttling characteristics. This paper is the first report verifying these virtues using a laboratory scale motor. There are several requirements for realizing this type of hybrid rocket: 1) high fuel filling rate for obtaining an optimal ${\zeta}$; 2) small port intervals for increasing port merging rate; 3) ports arrayed across the entire fuel section. Because these requirements could not be satisfied by common manufacturing methods, no previous researchers have conducted experiments with this kind of hybrid rocket. Recent advances in high accuracy 3D printing now allow for fuel to be produced that meets these three requirements. The fuel grains used in this study were produced by a high precision light polymerized 3D printer. Each grain consisted of an array of 0.3 mm diameter ports for a fuel filling rate of 98% .The authors conducted several firing tests with various oxidizer mass flow rates and chamber pressures, and analysed the results, including ${\zeta}$ history, using a new reconstruction technique. The results show that ${\zeta}$ remains almost constant throughout tests of varying oxidizer mass flow rates, and that regression rate in the axial direction is a nearly linear function of chamber pressure with a pressure exponent of 0.996.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.12
• /
• pp.1645-1652
• /
• 2018

A drone which was developed first for military purpose has been expanded to various civil areas, with its technological development. Of the drones developed for such diverse purposes, a drone for photography has a camera installed and is actively applied to a variety of image contents making, beyond filming and broadcasting. A drone for photography makes it possible to shoot present and dynamic images which were hard to be photographed with conventional photography technology. This study made a view finder which helps a drone operator to control a drone and directly view an object to shoot with the drone camera. The view finder for drones is a type of glasses. It was developed in the way of printing out the data modelled with 3D MAX in a 3D printer and installing a ultra-small LCD monitor. The view finder for drones makes it possible to fly a drone safely and achieve accurate framing of an object to shoot.

• Journal of radiological science and technology
• /
• v.41 no.6
• /
• pp.595-602
• /
• 2018

Quality control (QC) of Computed Tomography (CT) devices is based on image quality measurement on AAPM CT phantom which is a standard phantom. Although it is possible to control the accuracy of the CT apparatus, it is expensive and has a disadvantage of low penetration rate. Therefore, in this study, we make image quality measurement phantom at low cost using FFF (Fused Filament Fabrication) type three-dimensional printer and try to analyze the usefulness, compare it with existing standard phantom. To print a phantom, We used three-dimensional printer of the FFF system and PLA (Poly Lactic Acid, density: $1.24g/cm^3$) filament, and the CT device of 64 MDCT (Aquilion CX, Toshiba, Japan). In addition, we printed a phantom using three-dimensional printer after design using various tool based on existing standard phantom. For image quality evaluation, AAPM CT phantom and self-generated phantom were measured 10 times for each block. The measured data were analyzed for significance using the Mannwhiteney U-test of SPSS (Version 22.0, SPSS, Chicago, IL, USA). As a result of the analysis, phantom fabricated with three-dimensional printer and standard phantom showed no significant difference (p>0.05). Furthermore, we confirmed that image quality measurement performance of a phantom using three-dimensional printer is similar to the existing standard phantom. In conclusion, we confirmed the possibility of low cost phantom fabrication using three dimensional printer.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.142-144
• /
• 2016

Recent promising technologies of the manufacturing sector interest, and the interest in 3D printing that is expected to cause a huge ripple effect rapidly, and various types of products advertised in accordance with the falling price of 3D printers is spreading. However, the personal 3D printers that are currently being advertised is used for Injection output of the simple type that does not require a high processing precision in accordance with the limitation of technical performance, and consumer satisfaction is very low. In this paper, we propose a 3D printer, 3D precision to overcome existing limitations in the way the printer's high SLA 3D printer that combines injection method and the LSU (Laser Scanning Unit) in the office laser printer polygon mirror scanning method. 3D printers which are proposed to improve the accuracy and manufacturing speed is expected to replace the existing entry-level 3D printer.