• 폴리머
• /
• 제28권4호
• /
• pp.305-313
• /
• 2004

본 연구는 나노 복화공정을 이용하여 마이크로 혹은 나노공정에 응용이 가능한 형상모형 제작공정 개발과 폴리디메틸실록산 (polydimethylsiloxane)를 이용하여 만들어진 형상모형의 몰드로 나노급 정밀도의 폴리디메틸실록산 형상을 복제하는 공정에 관한 것이다. 본 연구에서 제안한 나노 복화공정은 복잡한 형상모형 (pattern)이나 2차원 형상을 CAD 파일 없이 비트맵 그림파일을 이용하여 직접적으로 200nm 정밀도를 가지는 형상으로 만들 수 있다. 형상모형은 펨토초 레이저를 이용하여 이광자 흡수 중합법으로 제작하기 때문에 형상의 정밀도는 레이저 범의 회절한계 이하로 얻을 수 있다. 이렇게 제작된 마스터 형상모형은 본 연구에서 제안한 진공압력차이법으로 폴리디메틸실록산 몰드를 제작하여 기존의 제작방법에 비하여 정밀한 제작이 가능함을 보였으며 또한 제작된 몰드를 이용하여 양각의 플리디메틸실록산 스탬프를 제작하였다.

• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.43-52
• /
• 2007

Offset printing is one of the well known printing technique of lithographic process and consists of image area and 'non-image area on a flat image carrier. The surface tension of dampening water can be controlled by adding IPA after mixing of raw water and etching solution. The etching solution contains a surfactant for reducing surface energy, a clean agent for non-imaging area, wetting agent for protecting non-imaging area from oil components like ink and also an emulsifying agent for controlling emulsification. In this study, the present situation of dampening water maintenance has examined by collecting dampening water using at domestic companies. The pH related to dampening water, conductivity, contact angle, emulsification curve are measured to define the current situation of dampening water control of each companies and to analyze the relationship among measured properties. In the study most of companies among 16 printing companies tested controlling dampening water through pH value. However, the quality of printing has varied depending upon conductivity, contact angle, IPA content, and emulsification value. The control of dampening water should be carry at the state of the standard when adding proper ratio of etching solution. It would be more effective when pH or conductivity control carries out in parallel with controlling dampening water. Therefore the concept that pH5.5 is correct is based concept. Based on these initial tests it is defined that the standardization of dampening water control is required.

• 펄프종이기술
• /
• 제42권2호
• /
• pp.41-45
• /
• 2010

This study was performed to evaluate the effect of paper property changes by internal addition of surface strength agent on printability. Advances in printing technique has required the development of paper qualities in many aspects. Basically paper structure is composed of hydrogen bonds which induce many problems in high speed printing machine because of weak bonding strength. One of the important printing problems is surface picking when mechanical pulp or recycled pulp are used. It was caused by the ink-stained blanket in printing process because accumulations of pollutant in white water and other elements which are bonded weakly or do not have hydrogen bonds. Debris at paper surface adheres to blanket which deteriorates printing efficiency and causes various problems. To complement these problems, Pennocel 5137 of polysaccharide structure was used as an agent to improve paper's surface property, strength and printability. Paper surface picking was analyzed by RI-1 test. As the dosage amount increased tensile strength, fiber bonding strength and ZDT strength were improved. Further more formation, smoothness and surface picking resistance were improved. It was confirmed that when adding polysaccharide structure polymers to improve surface strength such as surface picking resistance, it was also possible to improve tensile strength, fiber bonding strength, formation and smoothness.

• 한국정보통신학회논문지
• /
• 제21권10호
• /
• pp.1950-1956
• /
• 2017

정밀 푸드 프린팅 분야에서 출력 대상물의 정밀한 측위기술은 대단히 중요하다. 본 논문에서는 영상처리를 통하여 라떼 아트 프린터의 커피 잔을 정밀하게 측위하는 방법을 제안한다. 프린터 상단 측면에 설치된 카메라 센서로부터 얻은 이미지를 투영변환을 통하여 Top-View 이미지로 변환하고 이미지의 에지를 검출 후 Circular Hough 변환을 통하여 컵의 중심점 및 반지름을 검출하였다. 성능 평가 결과 0.1 ~ 0.125초의 영상 처리 속도, 92.26% 의 컵 검출률을 보여 라떼 아트 출력 소요 시간에 영향을 거의 주지 않으면서 거의 완벽하게 컵을 검출하는 것을 확인하였으며, 검출된 컵의 중심점 좌표 및 반지름 값들이 평균적으로 1.5mm 이내의 매우 적은 오차를 보여 본 논문이 해결하고자 했던 인쇄 위치 오차 문제를 해결한 것으로 평가된다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.171-171
• /
• 2012

In this study, we fabricated the high-brightness AlGaInP-based red light emitting diodes (LED)s using by direct printing technique and inductive coupled plasma (ICP) reactive ion etching (RIE). In general, surface roughening was fabricated by wet etching process to improve the light extraction efficiency of AlGaInP-based red LED. However, a structure of the surface roughening, which was fabricated by wet etching, was tiled cone-shape after wet etching process due to crystal structure of AlGaInP materials, which was used as top-layer of red LED. This tilted cone-shape of surface roughening can improve the light extraction of LED, but it caused a loss of the light extraction efficiency of LED. So, in this study, we fabricated perfectly cone shaped pattern using direct printing and dry etching process to maximize the light extraction efficiency of LED. Both submicron pattern and micron pattern was formed on the surface of red LED to compare the enhancement effect of light extraction efficiency of LEDs according to the diameter of sapphire patterns.After patterning process using direct printing and ICP-RIE proceeded on the red LED, light output was enhanced up to 10 % than that of red LED with wet etched structure. This enhancement of light extraction of red LED was maintained after packaging process. And as a result of analyze of current-voltage characteristic, there is no electrical degradation of LED.

• 한국전기전자재료학회논문지
• /
• 제26권11호
• /
• pp.841-845
• /
• 2013

We give a textured front on silicon wafer for high-efficiency solar cells by using micro contact printing method which uses PDMS (polydimethylsiloxane) silicon rubber as a stamp and SAM (self assembled monolayer)s as an ink. A random pyramidal texturing have been widely used for a front-surface texturing in low cost manufacturing line although the cell with random pyramids on front surface shows relatively low efficiency than the cell with inverted pyramids patterned by normal optical lithography. In the past two decades, the micro contact printing has been intensively studied in nano technology field for high resolution patterns on silicon wafer. However, this promising printing technique has surprisingly never applied so far to silicon based solar cell industry despite their simplicity of process and attractive aspects in terms of cost competitiveness. We employ a MHA (16-mercaptohexadecanoic acid) as an ink for Au deposited $SiO_2/Si$ substrate. The $SiO_2$ pattern which is same as the pattern printed by SAM ink on Au surface and later acts as a hard resist for anisotropic silicon etching was made by HF solution, and then inverted pyramidal pattern is formed after anisotropic wet etching. We compare three textured surface with different morphology (random texture, random pyramids and inverted pyramids) and then different geometry of inverted pyramid arrays in terms of reflectivity.

• Clinics in Shoulder and Elbow
• /
• 제27권1호
• /
• pp.72-78
• /
• 2024

Background: Clinical outcomes after fixation of distal humerus intraarticular fractures are directly related to the quality of reduction. The use of three-dimensional (3D)-printed fracture models can benefit preoperative planning to ensure good reduction. This review aims to determine if surgery performed with 3D printing assistance are faster and result in fewer complications and improved clinical outcomes than conventional methods. We also outline the benefits and drawbacks of this novel technique in surgical management of distal humerus fractures. Methods: A systematic literature search was carried out in various electronic databases. Search results were screened based on title and abstract. Data from eligible studies were extracted into spreadsheets. Meta-analysis was performed using appropriate computer software. Results: Three randomized controlled trials with 144 cases were included in the final analysis. The 3D-printed group had significantly shorter mean operating time (mean difference, 16.25 minutes; 95% confidence interval [CI], 12.74-19.76 minutes; P<0.001) and mean intraoperative blood loss (30.40 mL; 95% CI, 10.45-60.36 mL; P=0.005) compared with the conventional group. The 3D-printed group also tended to have fewer complications and a better likelihood of good or excellent outcomes as per the Mayo elbow performance score, but this did not reach statistical significance. Conclusions: Three-dimensional-printing-assisted surgery in distal humerus fractures has several benefits in reduced operating time and lower blood loss, indirectly decreasing other complications such as infection and anemia-related issues. Future good-quality studies are required to conclusively demonstrate the benefits of 3D printing in improving clinical outcomes.

• 한국산학기술학회논문지
• /
• 제18권11호
• /
• pp.802-809
• /
• 2017

3D 프린팅 제조 기술은 폴리머 및 금속 소재를 구조물 형상으로 적층하여 제품을 제작하는 성형기술로서, 설계 자유도가 높고 기능성을 요구하는 부품 제작에 유리하다. 또한 다품종 소량 생산 특성으로, 향후 철도 차량 부품 제작에 적합한 기술이다. 3D 프린팅 기술의 장점을 충분히 활용하기 위해서는 제품 설계시 공정 특성 고려가 필수이다. 이번 연구에서는 철도차량용 공기압축기의 열교환기를 대상으로, 3D 프린팅 기법 적용을 통한 제작을 위해, 성능과 공정조건을 고려한 제품의 재설계 및 제작 기술을 연구하였다. 먼저 열교환기의 성능을 높이기 위한 설계 컨셉을 정의하고 기존 열교환기의 시험을 통해 성능 분석 후, 이를 만족하기 위한 컨셉 설계 범위를 지정하였다. 또한 금속 3D 프린팅의 제작 한계 및 제작 시간, 특성 등을 고려하여, 상세 설계에 관한 수정을 진행하였다. 도출된 최종 설계안을 토대로, 알루미늄 소재를 사용하여 3D 프린팅 공정을 통해 제품을 제작하고 치수 정밀도를 만족함을 확인하였다. 최종 중량은 기존 제품 대비 41%의 중량 절감 효과를 보였다. 본 연구를 통해, 3D 프린팅 기술 활용을 위한 제품 설계 과정을 정립함으로써, 향후 3D 프린팅 기술 적용시 효율적인 설계가 가능할 것이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2007년도 제33회 하계학술대회 초록집
• /
• pp.371-371
• /
• 2007

• 한국건설순환자원학회지
• /
• 제19권1호
• /
• pp.57-60
• /
• 2024