• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.35-41
• /
• 2011

This work investigates the potential of in-cylinder thermal stratification and fuel stratification for extending the operating ranges in HCCI engines, and the coupling between thermal stratification and fuel stratification. Computational results areemployed. The computations were conducted using both a custom multi-zone version and the standard single-zone version of the Senkin application of the CHEMKINII kinetics rate code, and kinetic mechanism for di-methyl ether (DME). This study shows that the potential of thermal stratification and fuels stratification for extending the high-load operating limit by a staged combustion event with reduced pressure-rise rates is very large. It was also found that those stratification offers good potential to extend low-load limit by a same mechanism in high-load. However, a combination of thermal stratification and fuel stratification is not more effective than above stratification techniques for extending the operating ranges showing similar results of fuel stratification. Sufficient condition for combustion (enough temperature for) turns misfire in low-load limit to operate engines, which also leads to knock in high-load limit abruptly due to the too high temperature with high. DME shows a potential for maximizing effect of stratification to lower pressure-rise rate due to the characteristics of low-temperature heat release.

• 생물환경조절학회지
• /
• 제18권3호
• /
• pp.200-207
• /
• 2009

This study was conducted to analyze the variations of air temperature, relative humidity and pressure in a low pressure chamber for plant growth. The low pressure chamber was composed of an acrylic cylinder, a stainless plate, a mass flow controller, an elastomer pressure controller, a read-out-box, a vacuum pump, and sensors of air temperature, relative humidity, and pressure. The pressure leakage in the low pressure chamber was greatly affected by the material and connection method of tubes. The leakage rate in the low pressure chamber with the welding of the stainless tubes and a plate decreased by $0.21kPa{\cdot}h^{-1}$, whereas the leakage in the low pressure chamber with teflon tube and rubber O-ring was given by $1.03kPa{\cdot}h^{-1}$. Pressure in the low pressure chamber was sensitively fluctuated by the air temperature inside the chamber. An elastomer pressure controller was installed to keep the pressure in the low pressure chamber at a setting value. However, inside relative humidity at dark period increased to saturation level.. Two levels (25 and 50kPa) of pressure and two levels (500 and 1,000sccm) of mass flow rate were provided to investigate the effect of low pressure and mass flow rate on relative humidity inside the chamber. It was concluded that low setting value of pressure and high mass flow rate of mixed gas were the effective methods to control the pressure and to suppress the excessive rise of relative humidity inside the chamber.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1598-1603
• /
• 1994

A preliminary design procedure for a multi-stage axial compressor is developed, which is based on the stage-stacking method. It determines the flow coefficient which gives rise to the design conditions required such as pressure ratio, mass flow rate and rotational speed for a given specific mass flow rate at inlet to a compressor. With this flow coefficient, blade radii, every stage and compressor performance characterics such as stage pressure ratio, adiabatic efficiency etc. are calculated by stacking each stage performance characteristics. It is shown that there is an optimum number of stage which results in the maximum of compressor overall efficiency for a given specific mass flow rate at inlet to a compressor. A test design was tried for three different geometric design constraints, and comparison with a previous study shows that present procedure could be used reliably in determining the number of compressor stage in preliminary design stage.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권4호
• /
• pp.381-386
• /
• 2015

최근에 환경오염 문제와 대체에너지 문제에 많은 관심을 가지고 있다. 디젤기관은 세계적으로 연료의 경제성 때문에 사용이 증가할 것이다. 그러므로 선박용기관의 대기오염 문제도 여러 분야에서 큰 관심사가 되고 있다. 화석연료로 부터 배출되는 유해 배기가스를 줄이기 위하여 대체연료기술이 개발되고 있다. 이러한 신재생에너지의 바이오디젤연료는 기존 디젤연료를 대체할 친환경 에너지로 각광을 받고 있으며, 일정한 비율로 디젤연료와 혼합하면 기존 디젤기관에 개조 없이 사용가능하다. 본 연구에서 바이오디젤연료가 선박디젤기관의 연소특성에 미치는 영향을 분석하기 위하여 폐식용유로부터 제조된 바이오디젤유를 엔진에 적용하여 실험을 수행하였다. 폐식용 성분에는 세탄가와 점도가 높은 성분이 있고, 탄소함유량이 적으면서 산소함유량이 잔존하고 있다. 연구 결과 연료소비율은 증가하고, 압력, 압력상승율 및 열발생율은 감소하였다.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2001년도 춘계학술대회
• /
• pp.301-310
• /
• 2001

A study for the dangerous properties measurment of dust explosion was attended by the various dust concentration on Anthraquinone, Sodiumbenzoic acid, Corn starch, soy sauce powder, and cheese powder. As the result, maximum explosion pressure, the maximum rate of pressure rise, autoigntion temperature, and the water content of dust on lower limit explosion concentration was obtained as follows 1. The lower limit explosion concentration on soy sauce powder with the humidity of 65 to 90% increased by increasing the con tent of moisture, and the effect of dry air and moisture air decreased better in make of dry air. 2. The effect of a various dust concentration on autoigntion temperatures is investigated, If the vessel of dust explosion is small size and the easiness of autoignition was controled by air within the vessel, because it was better decreased air with increasing of dust concentration 3. The maximum explosion pressures of Anthraguinone, sodiumbenzoic acid, com starch, soy sauce powder, and cheese powder were 1.0g/$\ell$, 1.0g/$\ell$, 1.5g/$\ell$, 1.5g/$\ell$, and 1.5g/$\ell$, respectively, and the maximum rate of pressure rise were 0.5g/$\ell$, 0.5g/$\ell$, 1.0g/$\ell$, 1.0g/$\ell$, and 1.0g/$\ell$, respectively.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1527-1537
• /
• 1997

Extinction characteristics and acoustic response of hydrogen-air diffusion flames at various pressures are numerically studied by employing counterflow diffusion flame as a model flamelet in turbulent flames in combustion chambers. The numerical results show that extinction strain rate increases linearly with pressure and then decreases, and increases again at high pressures. Thus, flames are classified into three pressure regimes. Such nonmonotonic behavior is caused by the change in chemical kinetic behavior as pressure rises. The investigation of acoustic-pressure response in each regime, for better understanding of combustion instability, shows different characteristics depending on pressure. At low pressures, pressure-rise causes the increase in flame temperature and chain branching/recombination reaction rates, resulting in increased heat release. Therefore, amplification in pressure oscillation is predicted. Similar phenomena are predicted at high pressures. At moderate pressures, weak amplification is predicted since flame temperature and chain branching reaction rate decreases as pressure rises. This acoustic response can be predicted properly only with detailed chemistry or proper reduced chemistry.

• KIEAE Journal
• /
• 제16권3호
• /
• pp.95-101
• /
• 2016

Purpose: Recently, high-rise buildings are popular in korea due to high rate of land usage and cost performance in urban area. However, high-rise building causes several problems such as safety issues, cooling/heating load, stack effect, disaster prevention etc. The stack effect is one of the representative problems. Even though there are many researches on stack effect, there are few studies on design guideline considering local condition. Method: This study focuses on the change of pressure distribution according to the design factors which affects the airflow in high-rise residential buildings by simulation analysis. In this study, city, building floor, stairwell door leakage area, elevator door leakage area and changes of layout were considered ad the design factor. Result: The simulation results indicate that building height and ambient air temperature are significant design factor for stack effect.

• Applied Science and Convergence Technology
• /
• 제24권4호
• /
• pp.84-89
• /
• 2015

The base pressure and outgassing rate of a mild steel chamber were measured and compared to those of a stainless steel chamber. A combined sputter-ion and non-evaporable getter pump with a nominal pumping speed of 490 l/s generated the base pressure of $2.7{\times}10^{-11}$ mbar in the mild steel chamber and $1.2{\times}10^{-10}$ mbar in the stainless steel chamber. The rate-of-rise measurements show that the mild steel has an extremely low outgassing rate of $2.6{\times}10^{-13}$ mbar $ls^{-1}cm^{-2}$, which is about one-order of magnitude smaller than the outgassing rate of the stainless steels. Vacuum annealing of the mild steel at $850^{\circ}C$ reduced the outgassing rate further to $8.8{\times}10^{-14}$ mbar $ls^{-1}cm^{-2}$, which was comparable to the outgassing rate of a heat treated stainless steel for extreme-high vacuum use.

• 대한기계학회논문집B
• /
• 제36권5호
• /
• pp.563-569
• /
• 2012

추력 30톤급 액체로켓엔진에 대한 에너지 밸런스 해석을 수행하였다. 추력-연소압 관계, 추력-추진 제유량 관계 및 연소압-연료펌프상승 관계를 문헌에 공개된 실존 로켓엔진에 대한 데이터베이스와 비교하였다. 참고문헌의 분류에 따른 구형 설계보다 연소압이 높으며 이는 고성능 지향적이라는 의미를 가진다. 추력-추진제유량 비율은 기존엔진과 유사한 수준이었으며 이는 통상 수준의 비추력 성능을 의미한다. 연소압을 감안한 연료펌프의 압력상승은 높은 수준이며 이는 본 연구의 고려 대상인 엔진이 지상시험용으로서 차압설정이 최적화되지 않았기 때문이다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.55-60
• /
• 1999

A centrifugal compressor was tested with three different diffusers with plate vanes. The vane inlet angle was varied from 15 to 30 dog. The higher static pressure rises are obtained with lower vane stagger angle. In the stable region the static pressure field in vaneless space is very sensitive to flow rate. The impeller has a stabilizing effect over the whole stable operating range. The diffuser has a stabilizing effect at high flow rate but is destabilizing at low flow rate.