• 상하수도학회지
• /
• 제24권3호
• /
• pp.295-305
• /
• 2010

Role of the perforated pipe is to drain the water with equal pressure and velocity through the holes of perforated pipe. The perforated pipe is being used in many processes of water treatment system, however, the design parameter of perforated pipe is not standardized in korea. In this study, we have found the design parameter of perforated pipe in the water treatment system using the Computational Fluid Dynamics (CFD). The uniformity of outflow from the perforated pipe is directly affected according to area ratio(gross area of holes/surface area of the perforated pipe). In other words, the uniformity of outflow is improved as area ratio is smaller. Also, at the same area ratio, the uniformity of outflow is improved as number of holes is increase. Specially, in case of the two holes per length of pipe diameter(2/D) shows the most uniformity of outflow and the best hydraulic with the smaller pressure drop. The uniformity of outflow is aggravated and the pressure drop of pipe is decrease as length of pipe is longer. In case of that pipe length is 10m and above, the pressure drop decreased about 30% when diameter ratio is 40% with 0.2% of area ratio by comparison with 0.1% of area ratio.

• 한국추진공학회지
• /
• 제6권1호
• /
• pp.71-82
• /
• 2002

본 연구에서는 2차원의 압축성 Navier-Stokes 코드를 개발하여 mixer-ejector 노즐의 유동장 해석을 다양한 덕트와 노즐 면적비 및 노즐 압력비에 대하여 계산을 수행하였다. 덕트와 노즐 면적비 계산에서는 먼저 효율적인 2차 유동의 유입을 위한 최적의 면적비가 있음을 볼 수 있었다. 높은 면적비에서는 입구 자유유동의 적절한 혼합없이 mixing duct를 그대로 통과하는 것을 볼 수 있었고, 낮은 면적비에서는 제트의 경계가 유입 유동에 장애물로 작용하는 것을 볼 수 있었다. 노즐 압력비의 계산에 있어서는 shroud 벽면과 shock cell structure 간에 상호작용이 작다면 유입유량은 압력비에 따라 증가하는 것을 볼 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2354-2359
• /
• 2007

Influence of changing combustor pressure on flame stabilization and emission index in the swirl-stabilized flame was investigated. The combustor pressure was controlled by suction fan at combustor exit. Pressure index ($P^{\ast}$=Pabs/Patm), where Pabs and Patm indicated the absolute pressure and atmosphere pressure, respectively, was controlled in the range of 0.7${\sim}$1.3 for each equivalence ratio conditions. The flammable limits of swirl flames were largely influenced by changing combustor pressure and they showed similar tendency with laminar flames. NOx emission index decreased with decreasing pressure index for overall equivalence ratio conditions. R.m.s. of pressure fluctuations is increased with decreasing combustor pressure. This flame fluctuation caused incomplete combustion, hence CO emission index increased. These oscillating flames were measured by simultaneous $CH^{\ast}$ chemiluminescence time-series visualization and pressure fluctuation measurement.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2000년도 추계종합학술대회
• /
• pp.451-454
• /
• 2000

혈압을 측정하는 방법에는 침습적(Invasive)인 방법과 비침습적(Non-invasive)인 방법이 있는데 침습적인 방법에 의한 혈압측정의 경우 정확한 값을 얻는 반면에 그 사용법이 복잡하고 환자에게 불편하므로 중환자의 경우를 제외한 경우 대부분 비침습적인 방법에 의해 혈압을 측정한다. 현재 전자 혈압계의 경우 대부분이 오실로메트릭(Oscillometric) 방법을 사용하여 기본적인 시스템을 구성하고 여기에 여러 가지 알고리즘을 부가적으로 적용하고 있다. 본 연구에서 이러한 혈압 측정 시스템을 개발하기 위해 커프(Cuff)의 압력을 제어, 측정하고 측정된 데이터를 필터링하여 혈압을 측정할 수 있도록 알고리즘을 구성하였다. 통신방식으로는 개발된 시스템의 모든 기능이 개인용 컴퓨터(Personal Computer)와의 통신을 통해 이루어지도록 구성되어져 있으며, 사용된 통신방식은 비동기 직렬 통신 방식(RS-232)인 패킷방식을 사용하였고 솔레노이드(Solenoid) 밸브를 이용한 자동 또는 급속 배기 방법을 이용하여 커프의 압력을 감압(Deflation)하였다. 혈압측정 알고리즘은 기본적인 오실로메트릭 방법과 최대 진폭 알고리즘(Maximum Amplitude Algorithm)을 사용하였다. 최대진폭 알고리즘에서는 측정된 오실레이션(Oscillation)중 최고의 진폭을 가지는 오실레이션 같은 오차의 원인이 되는 연령이나 체중, 팔의 두께에 따라 다양하게 나타난다. 본 연구에서는 오실레이션의 간에 획일적인 비율을 적용하지 않고 여러 가지 요인들에 대한 가변적인 특정 비율(Characteristic Ratio)반영하여 보다 정확한 최고혈압(Systolic Blood Pressure), 최저혈압(Diastolic Blood Pressure), 평균혈압(Mean Blood Pressure)의 값을 구하는 연구를 하였다. 최고진폭 알고리즘에서 가변적인 특성비율의 적용은 혈압간의 오차를 줄일 수 있을것으로 기대된다.

• 한국분무공학회지
• /
• 제27권2호
• /
• pp.84-93
• /
• 2022

To implement carbon-neutrality in transportation sectors until 2050, hydrogen is considered a promising fuel for internal combustion engines because hydrogen does not contain carbon itself. Although hydrogen does not emit CO₂ emission from its combustion process, the low energy density in a volume unit hinders the adoption of hydrogen. Therefore, the understanding of hydrogen jet behavior and measurement of equivalence ratio must be conducted to completely implement the high-pressure hydrogen direct injection. The main objective of this research is feasibility test of hydrogen local equivalence ratio measurement by laser-induced breakdown spectroscopy (LIBs). To visualize the macroscopic structure of hydrogen jet, high-speed schlieren imaging was conducted. Moreover, LIBs has been adopted to validate the feasibility of hydrogen local equivalence ratio measurement. The hydrogen injection pressure was varied from 4 MPa to 8 MPa and injected in a constant volume chamber where the ambient pressure was 0.5 MPa. The increased injection pressure extends the vertical penetration of hydrogen jet. Due to the higher momentum supply when the injection pressure is high, the hydrogen has easily diffused in all directions. As the laser trigger timing has delayed, the low hydrogen atomic emission was detected due to the longer mixture formation time. Based on equivalence ratio measurement results, LIBs could be applied as a methodology for hydrogen local equivalence ratio measurement.

• 한국지반공학회논문집
• /
• 제40권4호
• /
• pp.19-32
• /
• 2024

동적 토압 해석은 지하 구조물의 내진 설계에서 핵심적인 파라미터이다. 그러나 기존 토압식들은 지반과 구조물의 상호작용, 상대적 유연성 비율(F) 및 구조물의 래킹 비율(R), 종횡비(L/H) 등 중요한 변수들을 종합적으로 고려하지 않은 것들이 대다수이다. 본 연구의 목적은 이러한 매개변수들이 동적 토압에 미치는 영향을 확인하여 기존의 옹벽 토압식의 신뢰도를 평가하는 것이며, 이를 위해 베이스먼트에 대해 동적 수치해석을 통한 매개변수 연구를 수행하였다. 그 결과, 종횡비가 높고 유연성이 낮은 구조물이 종횡비가 낮고 유연성이 높은 구조물보다 지진 토압에 더 취약하다는 사실을 확인하였다. 따라서 베이스먼트의 지진 토압 또는 동적 토압 추정에 있어 종횡비 및 유연비를 고려하는 것이 필요하고, 기존 옹벽의 토압식 적용 시 주의가 필요하다고 판단된다.

• 한국표면공학회지
• /
• 제39권6호
• /
• pp.250-254
• /
• 2006

Effect of hydrogen partial pressure ratio on the structural and electrical properties of highly c-axis oriented ZnO films deposited by oxygen ion-assisted pulsed filtered vacuum arc at a room temperature was investigated. The hydrogen partial pressure ratio were $1.4%\sim9.8%$ at 40% oxygen pressure ratio. The conductivity of ZnO:H films was increased from 1.4% up to 4.2% due to relatively high carrier mobility caused by improvement of crystallinity While the conductivity of ZnO:H films were decreased over than 4.2% and (0002) orientation was also deteriorated. The lowest resistivity of ZnO:H films was $2.5{\times}10^{-3}\;{\Omega}{\cdot}cm$ at 4.2% of hydrogen pressure ratio. Transmittance of ZnO:H films in visible range was 85% which is lower than that of undoped ZnO films because of declined preferred orientation.

• Journal of Chest Surgery
• /
• 제21권5호
• /
• pp.828-841
• /
• 1988

To predict the postoperative hemodynamic status of right ventricle preoperatively, a retrospective analysis was undertaken to determine the influence of pulmonary artery size on postoperative right ventricular pressure in 32 consecutive patients with tetralogy of Fallot who underwent total correction between July, 1987 to June, 1988 at the Department of Thoracic and Cardiovascular Surgery, Seoul National University Hospital. We have related the ratio of the postrepair peak systolic pressure in the right ventricle and the systemic systolic arterial pressure[PRV/Ao] to the preoperative cineangiographic measurement of pulmonary arterial tree, expressed as pulmonary artery index[PAI], the ratio of diameter of the right pulmonary artery to diameter of ascending aorta[r.PA/A.Ao], the ratio of right and left pulmonary artery to diameter of descending aorta[r.I.PA/D.Ao] There was tendency that the postrepair PRV/Ao seems to be related to the preoperative diameter of right and left pulmonary artery, but there were no statistically significant correlation with PAI, r.PA/A.Ao, r.l.PA/D. Ao to the ratio of the postoperative peak systolic right ventricular pressure and systemic systolic arterial pressure[PRV/Ao]. There was tendency to decrease the postoperative right ventricular pressure[PRV/Ao] about 11.2%[P < 0.025] within several hours than immediately after repair, but after then, there was no change of right ventricular pressure[PRV/Ao] significantly. There was good correlation of pressure change between the immediate and late postrepair right ventricular pressure[48 hour], and the derived linear regression line was; y=0.68534 0.1994[r=0.57294, P < 0.001]. There was no operative death due to residual high right ventricular pressure[PRV/Ao >0.75] related to hypoplastic pulmonary arterial development, thus we expect, for symptomatic patients even infants, that complete repair can be attempted when the pulmonary artery index[PAI] is over 108mm2/BSA, RPA/AAo is over 0.35, RPA LPA/D. Ao is over 1.36.

• 한국가스학회지
• /
• 제16권1호
• /
• pp.8-14
• /
• 2012

수소는 온실가스 배출을 저감하기 위한 미래 에너지로 고려되고 있지만, 폭발위험에 대한 문제점을 지니고 있다. 따라서 수소가 미래 에너지로 사용되기 위해서는 폭발위험에 대한 연구가 충분히 이루어져야 한다. 폭발위험은 폭발충격에 대한 이해 즉, 폭발과정에서 압력 상승속도에 대한 분석과 밀접한 관계가 있다. 본 연구에서는 폭발에 영향을 미치는 변수, 즉 연소 전후의 비열비, 화학평형상태에서 최대폭발압력, 그리고 연소속도, 이들 변수가 압력 상승속도에 미치는 영향을 살펴보았다. 화학평형상태에서 최대폭발압력과 연소속도는 압력 상승곡선에 큰 영향을 미치는 것을 알 수 있었고, 미연소 가스의 비열비는 초기압력 상승속도보다 최종압력 상승속도에 더욱 영향을 미치고, 연소가스의 비열비는 반대로 초기압력 상승속도에 더욱 큰 영향을 미치는 것을 알 수 있었다. 연소속도는 실험 데이터로부터 구하였으며 밀폐공간에서 수소가스 폭발에서는 폭연에서 폭굉으로 전이가 일어나기에는 연소속도가 매우 느림을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.318-327
• /
• 2002

In this paper, heat transfer and pressure oscillation characteristics on oscillating capillary tube heat pipe(OCHP) according to input heat flux, mixture ratio of working fluid and inclination angle were investigated and were compared single working fluid(R-142b) with binary mixture working fluid(R-142b-Ethano1). OCHP was made to serpentine structure of loop type with 10 turns by drilling the channels of length 220mm, width 1.5mm, and depth 1.5mm on the surface of brass plate. In this study, R-l42b and R-l42b-Ethanol were used as working fluids, the charging ratio of working fluids was 40(vol.%), the input heat flux to evaporating section was changed from 0.3W/㎠ to 1.8W/㎠, and mixture ratio of working fluid was R(100%), R(95%)-E(5%), R(90%)-E(10%), and R(85%)-E(15%). From the experimental results, it was found that the effective thermal conductivity of single working fluid was better than that of binary mixture working fluid. But, in case of binary mixture working fluid, critical heat flux was higher than that of single working fluid. And, the higher the mixture ratios of working fluid, the lower heat transfer performance. In case of pressure oscillation, as the inclination angle was lower, pressure wave was more irregular. These phenomena were more serious when the working fluid was binary mixture. Besides, when mixture ratio was higher, saturated pressure was increased, more irregular wave was observed and the mean amplitude was increased. For the same input heat flux, inclination angle and charging ratio, when pressure oscillation has sinusoidal wave, mean amplitude was small, and saturated pressure was low value, the heat transfer was excellent.