• 한국압력기기공학회 논문집
• /
• 제14권2호
• /
• pp.24-31
• /
• 2018

In this paper, specimen tests with simulated large seismic conditions have been carried out to investigate damage characteristics such as structural deformation and crack initiation under seismic loading. The mechanical behavior of the specimens is predicted by numerical simulations and the strain-based damage evaluations are performed. Finite element analyses of the specimens under the simulated seismic loading at room and operating temperatures were carried out for low alloy steel and stainless steel materials. Peak strain amplitude, cumulative fatigue damage and cumulative strain limit damage are calculated considering the nature of cyclic loading. In all cases, the allowable damage criteria are exceeded at the time of observing cracks visually in the tests. Therefore, it is confirmed that the material behavior due to the large seismic loads can be predicted by the numerical method and the structural damage of the materials can be evaluated conservatively based on the strain criteria.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.197-208
• /
• 2023

Rate-dependent mechanical response of sand, subjected to loading of medium to high strain rate range, is of interest for several civilian and military applications. Such rate-dependent response can vary significantly based on the initial density state of the sand, applied confining pressure, considered strain rate range, drainage condition and sand morphology. A numerical study has been carried out employing a recently proposed visco-plastic constitutive model to explore the rate-dependent mechanical behaviour of Toyoura sand under drained triaxial loading condition. The model parameters have been calibrated using the experimental data on Toyoura sand available in published literature. Under strain rates higher than a reference strain rate, the simulation results are found to be in good agreement with the experimentally observed characteristic shearing behaviour of sand, which includes increased shear strength, pronounced post-peak softening and suppressed compression. The rate-dependent response, subjected to intermediate strain rate range, has further been assessed in terms of enhancement of peak shear strength and peak friction angle over varying initial density and confining pressure. The simulation results indicate that the rate-induced strength increase is highest for the dense state and such strength enhancements remain nearly independent of the applied confinement level.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1995년도 추계학술대회
• /
• pp.151-153
• /
• 1995

Residual strain of artery is studied. There has been experimental evidence that residual strain exists in artery. When ring of artery is longitudinally cut, it is opened. Since strain has been determined without considering residual strain, the existence of residual strain is meaningful in mechanics of arterial wall. Intimal strain concentration is considered to be reduced with both account of residual strain and strain determined by loading. However, it is lack of experimental research. Therefore, this study experimentally attempts to quantify the effect of residual strain on circumferential strain which is determined under the assumption of zero strain with zero pressure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.731-734
• /
• 2002

This paper describes on the fabrication and characteristics of a ceramic thin-film pressure sensor based on Ta-N strain gauges for harsh environment applications. The Ta-N thin-film strain gauges are sputter deposited onto a micromachined Si diaphragms with buried cavity for overpressure protectors. The proposed device takes advantages of the good mechanical properties of single crystalline Si as diaphragms fabricated by SDB and electrochemical etch-stop technology, and in order to extend the operating temperature range, it incorporates relatively the high resistance, stability and gauge factor of Ta-N thin-films. The fabricated pressure sensor presents a low temperature coefficient of resistance, high sensitivity, low non-linearity and excellent temperature stability. The sensitivity is $1.097{\sim}1.21mV/V{\cdot}kgf/cm^2$ in the temperature range of $25{\sim}200^{\circ}C$ and the maximum non-linearity is 0.43 %FS.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권2호
• /
• pp.1-7
• /
• 1999

we evaluated the effects of joining process such as contact method. shape of joined area and pressure on the electrical and mechanical properties of Bi-2223 superconducting tape, Specifically. the current capacity of the jointed tape was measured as a function of uniaxial pressure. and the thermal shock, bonding strength and the thermal of the tape were evaluated and correlated to the microstructural evolution. It was observed that the current capacity was significanrly dependent on the uniaxial pressure The jointed tape, fabricated with a pressure of 1,000-1,600 Mpa. showed the highest value of current capacity results from improvements in core density, contacting area and grain alignment, ect. In addition, the strength of jointed tape was measured to be 86 Mpa, which is about 88% of the unjoined ape's strength. The irreversible strain($\varepsilon$irrev) for the jointed tape was measured to be 0.1%, smaller than that of unjoined tape ($\varepsilon$irrev= 0.3%). The decrease in the strength and irreversible strain for jointed tape is believed to be due to the irregular geometry/morphology of the transition area of the tape.

• Composites Research
• /
• 제14권3호
• /
• pp.10-17
• /
• 2001

복합재료 압력용기를 개발하기 위하여 설계, 제작, 시험을 연계한 연구가 수행되었다. 섬유의 와인딩 패턴 및 각도는 CADFIL 코드를 활용하여 결정하였고, 그 각도는 [$liner/15^{\circ}/15^{\circ}/90^{\circ}/18^{\circ}/90^{\circ}/21^{\circ}/21^{\circ}/90^{\circ}$] 이었다. 압력용기의 제작은 5축 필라멘트 와인딩기를 활용하여 이루어졌다. 제조 공정 중에 광섬유 센서를 매립하여 내부 압력이 가해질 때 각 지점에서 스트레인을 측정하였다. 광섬유가 실험적으로 사용된 반면에 일반적으로 적용하는 스트레인 게이지를 부착하여 안정적인 시험결과를 확보하였다. 가압 시험결과는 유한요소 해석 결과와 비교하였고 그 결과는 유사한 일치를 보여주었다. 이 과정을 통하여 개구부 한개를 지닌 복합재료 압력용기의 설계, 제작 및 시험평가가 성공적으로 이루어져 제조기술의 확보가 가능하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.815-818
• /
• 2002

The elliptic relaxation model(ERM) with the inhomogeneous correction intermediate between near wall with and far from the wall. The source of the ERM usually was appled quasi-homogeneous pressure-strain correlation in homogeneous situations. This formulation was easily applied to the linear model or non-linear pressure-strain model. It is observed that the boundary conditions of the relaxation operator dominate the homogeneous pressure-strain model in the near wall region. While looking at high-Reynolds number flows, it was found necessary to modify the effect of the relaxation operator throughout the log region by accounting for gradients of the flatness variable and turbulent length scales. These effects are kinematic blocking of the wall normal velocity fluctuation and pressure reflections from the surface. This model is wall distances and unit vectors which make the model applicable to flows boundary by a complex geometry. Inhomogeneous correction model is computed inertial and non-inertial channel flow These are compared DNS(Kim et at., Kristofffrsen & Andersson) for channel flow. The present model could be predicted well for rotating flows.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.239-246
• /
• 2003

This paper proposes engineering estimation equations of elastic-plastic J and COD fur axial through-wall cracked pipes under internal pressure. Based on detailed 3-D FE results based on deformation plasticity, the plastic influence functions for fully plastic J and COD solutions are tabulated as a function of the mean radius-to-thickness ratio, the normalized crack length. and the strain hardening. Based on these results, the GE/EPRI-type J and COD estimation equations are proposed and validated against the 3-D FE results based on deformation plasticity. For more general application to general stress-strain laws or to complex loading, the developed GE/EPRI-type solutions are re-formulated based on the reference stress concept. Such a reformulation provides simpler equations for J and COD, which are then further extended to combined internal pressure and bending. The proposed reference stress based J and COD estimation equations are compared with elastic-plastic 3-D FE results using actual stress-strain data for Type 316 stainless steels. The FE results for both internal pressure cases and combined internal pressure and bending cases compare very well with the proposed J and COD estimations.

• 한국기계가공학회지
• /
• 제21권6호
• /
• pp.60-66
• /
• 2022

The optimal strain energy function was obtained by comparing the results of the analysis using the strain energy functions obtained by uniaxial tensile and equibiaxial tensile tests on gasket materials used in hydrogen fuel cells, with the results measured using a contact pressure measurement sensor. At this time, even when only the uniaxial tensile test was conducted, Yeoh could obtain the most accurate results even by conducting only the uniaxial tensile test. Using this, an analysis of the cross section of the gasket used in stack confirmed a safe contact pressure and no deformation on the separator. In the future, research will be conducted to verify the gasket durability by reliability evaluation.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1527-1537
• /
• 1997

Extinction characteristics and acoustic response of hydrogen-air diffusion flames at various pressures are numerically studied by employing counterflow diffusion flame as a model flamelet in turbulent flames in combustion chambers. The numerical results show that extinction strain rate increases linearly with pressure and then decreases, and increases again at high pressures. Thus, flames are classified into three pressure regimes. Such nonmonotonic behavior is caused by the change in chemical kinetic behavior as pressure rises. The investigation of acoustic-pressure response in each regime, for better understanding of combustion instability, shows different characteristics depending on pressure. At low pressures, pressure-rise causes the increase in flame temperature and chain branching/recombination reaction rates, resulting in increased heat release. Therefore, amplification in pressure oscillation is predicted. Similar phenomena are predicted at high pressures. At moderate pressures, weak amplification is predicted since flame temperature and chain branching reaction rate decreases as pressure rises. This acoustic response can be predicted properly only with detailed chemistry or proper reduced chemistry.