• Ocean and Polar Research
• /
• v.25 no.spc3
• /
• pp.361-371
• /
• 2003

The effect of bottom friction on the steady wind-driven circulation in the Yellow Sea and the East China Sea (YSECS) has been studied using a two-dimensional numerical model with and without tidal forcing. Upwind flow experiment in YSECS has also been carried out with a schematic time variation in the wind field. The surface water setup and circulation pattern due to steady wind forcing are found to be very sensitive to the bottom friction. When the effects of tidal currents are neglected, the overall current velocities are overestimated and eddies of various sizes appear, upwind flow is formed within the deep trough of the Yellow Sea, forming a part of the topographic gyre on the side of Korea. When tidal forcing is taken into account, the wind-induced surface elevations are smoothed out due to the strong tide-induced bottom friction, which is aligned almost normal to the wind stresses; weak upwind flow is farmed in the deep trough of the Yellow Sea, west and south of Jeju. Calculation with wind forcing only through a parameterized linear bottom friction produces almost same results from the calculation with $M_2$ tidal forcing and wind forcing using a quadratic bottom friction, supporting Hunter (1975)'s linearization of bottom friction which includes the effect of tidal current, can be applied to the simulation of wind-driven circulation in YSECS. The results show that steady wind forcing is not a dominant factor to the winter-time upwind flow in YSECS. Upwind flow experiment which considers the relaxation of pressure gradient (Huesh et al. 1986) shows that 1) a downwind flow is dominant over the whole YSECS when the northerly wind reaches a maximum speed; 2) a trend of upwind flow near the trough is found during relaxation when the wind abates; 3) a northward flow dominates over the YSECS after the wind stops. The results also show that the upwind flow in the trough of Yellow Sea is forced by a wind-induced longitudinal surface elevation gradient.

• Journal of Internet Computing and Services
• /
• v.8 no.1
• /
• pp.33-45
• /
• 2007

Using switches and sensors informing the current on or off state, this paper suggests a sleeping control and remote monitoring system that not only can recognize the sleeping situations but also can control for keeping an appropriate sleeping situation remotely, And we show an example that this system is applied to the healthcare sleeping mat, Our system comprises the following 3 parts: a part for detecting the sleeping situations, a part for extracting sensing data and sending/receiving the relating situated data, and a part controlling and monitoring the all of sleeping situations. In details, in order to develop our system, we used the touch and pressure-sensitive sensors with On/Off functions for a purpose of the first part, The second part consists of the self-developed embedded board with the socket based communication as well as extracting real-time sensing data. And the third part is implemented by service modules for providing controlling and monitoring functions previously described. Finally, these service modules are implemented by the TMO scheme, one of real-time object-oriented programming models and the communications among them is supported using the TMOSM of distributed real-time middleware.

• Journal of Trauma and Injury
• /
• v.27 no.4
• /
• pp.126-132
• /
• 2014

Purpose: The field trauma triage for injured patients is essential for trauma care system. In this study, agreement of patient evaluation between by prehospital EMS personnel and by hospital staffs and the appropriateness of prehospital triage were evaluated. Methods: This observational study was conducted from September to October 2012 for 5 weeks. During this period, EMT evaluated patient's severity according to guideline for field triage and recorded. Same guideline was applied in 26 hospitals for patients with EMS use. Kappa statistics were used to measure agreement for each item of guideline. Finally, over-triage and under-triage rate of EMT were calculated. Results: During study period, total 3,106 patients were transferred to 26 hospital emergency departments with EMS use. Kappa statistics for "vital signs" items were 0.45 for mentality lower than V and 0.44 for systolic blood pressure lower than 90 mmHg as a moderate agreement. In "anatomy of injury" items Kappa statistics were very low. In "mechanism of injury" items Kappa statistics were 0.28 for high-rise fall down and 0.27 for high energy traffic accident but in other items Kappa statistics were very low. 362 patients (12.0%) were over-triaged and 281 patients (9.3%) were under-triaged. Conclusion: Field triage can be applied but need to evaluate and modify in order to become accurate and sensitive for decision of transportation.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.360-364
• /
• 2010

Most research groups used two analysis methods (spectroscopy and nanotribology) to measure the mechanical properties of nano-materials: NMR (Nuclear Magnetic Resonance), IR (Infrared Spectroscopy), Raman Spectroscopy as the spectroscopy method and AFM (Atomic Force MicroScope), EFM (Electrostatic Force Microscope), KFM (Kelvin Force Microscope), Nanoindenter as the nanotribological one. Among these, the nano-indentation technique particularly has been recognized as a powerful method to measure the elastic modulus and the hardness. However, this technique are prone to considerable measurement errors with pressure conditions during measurement. In this paper, we measured the change of elastic modulus and hardness of an Al single crystal with the change of load, hold, and unload time, respectively. We found that elastic modulus and hardness significantly depend on load, hold, and unload time, etc. As the indent time was shortened, the elastic modulus value decreased while the hardness value increased. In addition, we found that elastic modulus value was more sensitive to indent load, hold, and unload time than the hardness value. We speculate that measurement errors of the elastic modulus and the hardness originate from the residual stress during indenting test. From our results, the elastic modulus was more susceptible to the residual stress than the hardness. Thus, we find that the residual stress should be controlled for the minimum measurement errors during the indenting test.

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.30-36
• /
• 1996

ZnO thin-film sensors were fabricated by RF magnetron sputtering method. The composition of the device material was 4 wt. % $Al_{2}O_{3}$, 1 wt. % $TiO_{2}$ and 0.2 wt. % $V_{2}O_{5}$ on the basis of ZnO material for developing the high sensitive TMA gas sensor which have an appropriate resistivity and the stability for practical use. They were also grown on the $SiO_{2}/Si$ substrates heated at $250^{\circ}C$ under a pure oxygen pressure of about 10 mTorr with a power of about 80 watts for 10 minutes. So as to enhance the stability of the resistivity, the thin films were annealed from $400^{\circ}C$ to $800^{\circ}C$. The sensors made with the thin film which were annealed at $700^{\circ}C$ for 60 minutes in pure oxygen gas exhibited a good sensing properties for TMA gas. The thin film grown at this condition showed the maximum sensitivity of 550 in TMA gas concentration of 160 ppm, and exhibited a good stability and excellent linearity.

• Korean Journal of Food Science and Technology
• /
• v.43 no.3
• /
• pp.277-281
• /
• 2011

A rapid and very sensitive high-performance liquid chromatography/atmospheric-pressure chemical-ionization mass spectrometry method to detect ethylenethiourea (ETU) fungicide residues in fruits was developed. Methylene chloride was used as the surface extraction solvent for the target component. Recovery rates improved when cysteine hydrochloride and sodium carbonate were added to product prior to fortification. The limits of detection and quantification were approximately 0.006 and 0.02 mg/kg, respectively, from mandarin oranges. Recoveries from mandarin oranges, oranges, bananas, and pears, spiked in the range of 0.05-0.5 mg/kg, averaged 80-100%. The proposed method was used to monitor the presence of ETU in commercial fruits purchased from different markets in Seoul, Korea. ETU was found in four orange peels and in three mandarin orange peel samples. The highest ETU residue levels were $73.6{\mu}g/kg$ and $29.8{\mu}g/kg$.

• The Journal of the Korean dental association
• /
• v.46 no.11
• /
• pp.683-688
• /
• 2008

Purpose : The aim of this study was to evaluate the clinical efficacy of two commercially available desensitizing agents over 3 weeks on patients with dentin hypersensitivity. Materials and Methods : An oxalate-based solution, Sensblok (NIBEC Inc. Seoul, Korea) & Superseal (Pheonix Inc. Michigan, USA), and a distilled water placebo were compared in a clinical setting. Seven volunteers exhibiting three or more teeth that were sensitive to tactile & air were enrolled in the study (35 teeth total). A visual analog scale (VAS) was used for recording each patient s level of sensitivity to tactile & air stimuli. A Florida probe was rubbed across the exposed dentin three times with a constant pressure 20 grams to measure the tactile stimulus. The air stimulus was generated by dental unit air syringe for 1-second blast from 1/2 inch distance. The desensitizing agents were applied according manufacture s guideline. VAS scores were recorded at baseline, 1 minute after treatment, at 1 week, 2weeks, 3weeks. VAS score were analyzed using a repeated measures ANOVA ( =0.05). Results : The Sensblok, Superseal, and distilled water placebo all decreased dentin sensitivity. A statistically significant difference existed between Sensblok and placebo when tactile stimulus was applied (P<0.05), but no significant difference was found among other desensitizing agents and tactile and air stimuli.

• Nuclear Engineering and Technology
• /
• v.14 no.4
• /
• pp.186-195
• /
• 1982

The steam line break accident for Kori Unit 1 is analyzed by a code SYSRAN which calculates nuclear power and heat flux using the point kinetics equation and the lumped-parameter model and calculates system transient using the mass and energy balance equation with the assumption of uniform reactor coolant system pressure. The 1.4 f $t^2$ steam line break accident is analyzed at EOL (End of Life), hot shutdown condition in which case the accident would be most severe. The steam discharge rate is assumed to follow the Moody critical flow model. The results reveal the peak heat flux of 38% of nominal full power value at 60 second after the accident initiates, which is higher than the FSAR result of 26%. Trends for the transient are in good agreement with FSAR results. A sensitivity study shows that this accident is most sensitive to the moderator density coefficient and the lower plenum mixing factor. The DNBR calculation under the assumption of $F_{{\Delta}H}$=3.66, which is used in the FSAR with all the control and the shutdown assemblies inserted except one B bank assembly and of Fz=1.55 shows that minimum DNBR reaches 1.62 at 60 second, indicating that the fuel failure is not anticipated to occur. The point kinetics equation, the lumped-parameter model and the system transient model which uses the mass and energy balance equation are verified to be effective to follow the system transient phenomena of the nuclear power plants.lear power plants.

• Journal of the Korean Chemical Society
• /
• v.37 no.4
• /
• pp.453-461
• /
• 1993

Detection method was developed using a simply designed photochemical reactor made of teflon coil and low pressure mercury lamp. This method of UV photolysis of analytes followed by UV, fluorescence and electrochemical detection was found to be useful for four thiocarbamates. Analytes eluting from the column are irradiated with a high flux of 254 nm UV light, so that they change to either fluorescent active forms or highly electrochemically sensitive products. Appling this technique to the UV detection, thiocarbamates were converted into long wavelength absorbing products upon UV irradiation. In fluorescence detector four thiocarbamates are not detected at nonirradiated condition but fluorescence signals of MPTC, CPTC photolysates are appeared after irradiation with UV light. The electrochemical detection for the determination of thiocarbamates was enhanced up to 5∼20 fold signal after UV irradiation, compared to that of the nonirradiated. The detection limit of thiocarbamates on electrochemical detector was 13.3∼0.02 ng under pH 7.0, ionic strength $0.5{\times}10^{-2}$ M, phosphate buffer solution. Adducts produced by reaction of photolysates and OPA-MERC in the reaction coil were monitored at 425 nm with fluorescence detector, and one of the photolysates was primary amine.

• Journal of Adhesion and Interface
• /
• v.11 no.3
• /
• pp.120-125
• /
• 2010

UV-curable acrylic Pressure-sensitive adhesives (Acrylic PSAs) are used in many different parts in the world. A wafer manufacture process which is based on semiconductor industry is one thing. We have used acrylic PSAs whose thickness is different from $20{\mu}m$ to $30{\mu}m$ in wafer manufacture process so far. But as wafers become more thinner, acrylic PSAs are supposed to satisfy the requirements such as proper adhesion performance. The main purpose of this research is studying proper adhesion performance and UV-curing behavior of UV-curable acrylic PSAs with very thin thickness and then determining optimized conditions to raise the efficiency of thin wafer production. Acrylic PSAs contain 2-Ethylhexyl Acrylate (2-EHA), Acrylic Acid (AA) and Butyl Acrylate (BA). Ethyl acetate (EtAc) is used as solvent. The acrylic PSAs are obtained using solvent polymerization. Thickness of UV-curable acrylic PSAs is different from $10{\sim}30{\mu}m$. By peel strength and probe tack, adhesion performance and UV curing behavior of acrylic PSA are concerned.