• Nuclear Engineering and Technology
• /
• 제48권6호
• /
• pp.1321-1329
• /
• 2016

To get an insight into the operating characteristics of the passive residual heat removal system of molten salt reactors, a two-phase natural circulation test facility was constructed. The system consists of a boiling loop absorbing the heat from the drain tank, a condensing loop consuming the heat, and a steam drum. A steady-state experiment was carried out, in which the thimble temperature ranged from $450^{\circ}C$ to $700^{\circ}C$ and the system pressure was controlled at levels below 150 kPa. When reaching a steady state, the system was operated under saturated conditions. Some important parameters, including heat power, system resistance, and water level in the steam drum and water tank were investigated. The experimental results showed that the natural circulation system is feasible in removing the decay heat, even though some fluctuations may occur in the operation. The uneven temperature distribution in the water tank may be inevitable because convection occurs on the outside of the condensing tube besides boiling with decreasing the decay power. The instabilities in the natural circulation loop are sensitive to heat flux and system resistance rather than the water level in the steam drum and water tank. RELAP5 code shows reasonable results compared with experimental data.

• 동력기계공학회지
• /
• 제6권1호
• /
• pp.20-26
• /
• 2002

The purpose of this study is preventing the stick, scuffing, scratch between piston and cylinder in advance, and obtaining data for duration test in actual engine operation. The temperature gradient in cylinder bore according to coolant temperature were measured using $1.5{\ell}$ class diesel engine. 20 thermocouples were installed 2mm deep inside from cylinder wall near top ring of piston in cylinder block, at which points major thermal loads exist. It is suggested as proper measurement points for engine design by industrial engineers. Under full load and $70^{\circ}$, $80^{\circ}C$ and $90^{\circ}C$ coolant temperature conditions, the temperature in cylinder block and engine oil increased gradually according to the increase of coolant temperature, the siamese side temperature of top dead center is $142^{\circ}C$ in peripheral distribution, that is about $20^{\circ}C$ higher than that at thrust, anti-thrust, and rear side temperature, respectively. The maximum pressure of combustion gas in $70^{\circ}C$ coolant temperature is about 2 bar lower than those of $80^{\circ}C$ and $90^{\circ}C$ coolant temperature. The engine torque in $80^{\circ}C$, $90^{\circ}C$ coolant temperature condition is about 4.9Nm higher than that of $70^{\circ}C$ coolant temperature.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.192-196
• /
• 2005

Key part of main equipment in a gas turbine may be likely to be damaged due to operation under high temperature, high pressure, high-speed rotation, etc. Accordingly, the cost for maintenance increases and the damaged parts may cause generation to stop. The number of parts for maintenance also increases, but diagnostics technology fur the maintenance actually does not catch up with the demand. Blades are made of precipitation hardening Ni superalloy IN738 and the like for keeping hot strength. The surface of a blade is thermal-sprayed, using powder with main compositions such as Ni, Cr, Al, etc. in order to inhibit hot oxidation. Conventional regular maintenance of the coating layer of a blade is made by FPI (Fluorescent Penetrant Inspection) and MTP (Magnetic Particle Testing). Such methods, however, are complicated and take long time and also require much cost. In this study, defect diagnostics were tested for the coating layer of an industrial gas turbine blade, using an infraredthermography camera. Since the infrared thermography method can check a temperature distribution on a wide range of area by means of non-contact, it can advantageously save expenses and time as compared to conventional test methods. For the infrared thermography method, however, thermo-load must be applied onto a tested specimen and it is difficult to quantify the measured data. To solve the problems, this essay includes description about producing a specimen of a gas turbine blade (bucket), applying thermo-load onto the produced specimen, photographing thermography images by an infrared thermography camera, analyzing the thermography images, and pre-testing for analyzing defects on the coating layer of the gas turbine blade.

• 한국소음진동공학회논문집
• /
• 제14권7호
• /
• pp.604-611
• /
• 2004

It is well known that wall impedance essentially determines how sound wave transmits from one place to another. The wall impedance is related with its dynamic properties : for example, the mass, stiffness, and damping characteristics. It is noteworthy, however, that the wall impedance is also function of spatial characteristics of two spaces that is separated by the wall. This is often referred that the wall is not locally reacting. In this paper, we have attempted to see how the acoustic characteristics of the two spaces is affected by various structure parameters such as density, applied tension, and a normalized length of the wall. Calculations are conducted for two different modally reacting boundary conditions by modal expansion method. The variation of the Helmholtz mode and the structural-dominated mode are analyzed as the structure parameters vary. The displacement distribution of the structure, pressure and active intensity of the inside and outside cavity are presented at the Helmholtz mode and the structure-dominated mode. It is shown that the frequency characteristics are governed by both structure-and fluid-dominated mode. The results exhibit that the density of the structure is the most sensitive design parameter on the frequency characteristics for the coupling system as we could imagine in the beginning. The Helmholtz mode frequency decrease as density increases. However. it increases as applied tension and an opening size increase. The bandwidth of the Helmholtz mode is mainly affected by density of the structure and its opening size.

• 한국소음진동공학회논문집
• /
• 제18권1호
• /
• pp.20-25
• /
• 2008

음향홀로그래피는 시간 영역 혹은 주파수 영역에서 음압의 공간 분포를 가시화하는 방법이다. 그러나, 재구성된 음압은 종종 실제적으로 우리가 원하는 음장의 정보보다 훨씬 많은 정보를 가지고 있다. 예를 들어, 우리가 소음 제어를 위해 필요로 하는 정보는 소음원의 위치와 전체적인 방사형태의 정보만으로 충분하다. 따라서, 이렇게 필요로 하는 정보만을 보여줄 수 있는 방법이 필요하다 볼 수 있다. 이를 위한 한 가지 방법으로 공간에서의 포락을 생각할 수 있다. 공간복소포락은 소음원의 위치와 느리게 변하는 전체적인 변화에 대한 정보를 가지고 있는 포락 신호를 의미한다. 공간복소포락을 이용함으로써, 우리는 음장에서 불필요한 정보를 제거하여 필요한 정보를 얻을 수 있을 뿐만 아니라, 가시화 과정에서의 연산 시간도 줄일 수 있다. 이 공간포락을 얻기 위한 공간변조 방법을 이론적으로 유도하고 제안한다. 그리고, 여러 개의 단극음원에 의해 형성되는 복잡한 음장을 제안하는 방법을 이용해 단순화시킨 결과를 통해 제안하는 방법에 대한 타당성을 검증한다.

• 한국해양학회지:바다
• /
• 제12권3호
• /
• pp.244-250
• /
• 2007

MIMS 시스템은 액체 시료의 용존 가스 농도를 정확하게 측정하는데 이용되어 왔는데, 본 연구에서는 해수와 퇴적물 공극수에 존재하는 용존 메탄 농도를 정량화하는데 사용되었다. 측정의 정밀성을 파악하기 위하여, 여러 분압의 메탄 농도에 대해서 포화된 액체 시료를 준비하였으며 이를 MIMS 시스템으로 측정하였다. 측정된 값은 용존 기체의 포화 상수로부터 계산된 값과 잘 일치하였다. 측정의 표준 오차는 평균값의 $0.13{\sim}0.9%$ 정도였다. 이 시스템을 이용하여 한반도 남해안 인근 해수의 용존 메탄 농도를 측정한 결과, 용존 메탄의 깊이별 분포는 물리적인 요소가 좌우하고 있음을 알 수 있었다. MIMS system을 이용하여, 각 수괴 간의 미세한 용존 메탄 농도의 차이를 구분하여 살펴볼 수 있었다. 또 다른 실험에서는 MIMS 시스템의 inlet 부분을 탐침 형태로 제작하여 퇴적물 깊이에 따른 용존 메탄을 측정할 수 있었다.

• Journal of Nutrition and Health
• /
• 제32권8호
• /
• pp.908-917
• /
• 1999

This study was done to compare nutrient intakes, anthropometric indices, and psychosocial factors related to smoking by smoking status among adolescent girls in Seoul. Subjects were high school students, and smokers were 17.6%. Nutrient intakes were analyzed by convenient method, and anthropometric measurements were done by Inbody 2.0. Psychosocial factors of smoking were examined based on the Theory of Planned Behavior : 26 attitudinal, 9 normative, and 17 control beliefs were used. Smokers smoked 5-7 cigarettes a day on average, with 1.26 pack-years of smoking, There were no significant differences in anthropometric characteristics, except fat distribution, between smoking(n=92) and nonsmoking(n=92) and nonsmoking(n=94) group. The percentage of alcohol groups. Especially, caloric intake (63.6% of RDA) were much below the recommended level. With respect to psychosocial factors, 18 out of 26 attitudinal beliefs were significantly different between smokers and nonsmokers. Smokers responded less negatively on the items of bad health effects of relax(p<0.001). In addition, smokers were more convinced of advantages of smoking (test, etc.)but responded less negatively on the disadvantages of smoking(bothering others, yellow teeth, bad breath, etc.). Smokers expressed less pressure for not smoking from siblings, friends, school seniors than nonsmokers. In addition, smokers, expressed less confidence in controlling the urge to smoker or quitting smoking in several situations, such as 'after a meal', 'feel bored', 'with friends', 'when angry' offered a cigarette by friends', 'drinking coffee or tea', 'drinking alcohol', 'seeing others smoke'(p<0.001). Smokers also felt less developing in applying specific skills for controlling the urge to smoker or quitting smoking. These findings suggest the need for developing smoking cessation programs for adolescent females, focusing on specific beliefs identified in this study.

• 한국해양공학회지
• /
• 제30권4호
• /
• pp.310-319
• /
• 2016

If a spoiler was attached to the pipeline investigated in a previous study, a strong flow and vortex at the lower part caused scouring and thus an asymmetric pressure distribution, which assisted in the analysis of the self-burial structure where a down force was applied to the pipe. However, only the fluid-pipe interaction was considered, excluding the medium (seabed), when practically burying the pipeline. Thus, this study applied a numerical model (LES-WASS-2D) to directly analyze the non-linear interactions among the fluid, pipe, and seabed in order to perform numerical simulations of a pipeline with a spoiler installed on the seabed. This allowed the self-burial mechanism of a pipeline with a spoiler to be analyzed in the same context as the previous study that considered only the fluid-pipe interaction. However, when a pipeline was installed on the seabed, a strong flow and vortex were found at the front of the bottom, and a spoiler accelerated the fluid resistances. This hydraulic phenomenon will reinforce the scouring and down force on the pipeline. In the general consideration of the numerical analysis results by the specifications and arrangements of the spoiler, a pipeline with a spoiler was found to be the most effective for the self-burial function.

• 방사선산업학회지
• /
• 제9권3호
• /
• pp.119-126
• /
• 2015

In Shinjeong-dong of Jeongeup, there are three government-supported research institutes and an RFT industrial complex which is currently being established. Increased human activities can affect flora and fauna as a man-made pressure onto the region. As a baseline study, status of exotic plants was investigated prior to a full operation of the RFT industrial complex. A total of 54 species and 1 variety of naturalized or introduced plants were found in the study area. Among them, three species (Ambrosia artemisifolia var. elatior, Rumex acetocella and Aster pilosus) belong to 'nuisance species', and four species(Phytolacca americana, Iopomoea hederacea, Ereechtites hieracifolia and Rudbeckia laciniata) to 'monitor species' designated by the ministry of Environment. Some of naturalized trees and plants were intentionally introduced in this area, while others naturally immigrated. Physalis angulata seemes to immigrate in the study area in the form of mixture with animal feeds as its distribution coincided with the transportation route of the animal feeds. Liquidambar styraciflua is amenable to the ecological investigation on the possible expansion of the species to the nearby Naejang National Park as its leave shape and autumn color are very similar to those of maple trees. The number of naturalized plants around the RFT industrial complex will increase with an increase in floating population, in human activities in association with constructions of factories and operations of the complex. The result of this study provides baseline data for assessing the ecological change of the region according to the operation of the RFT industrial complex.

• 한국지형학회지
• /
• 제24권3호
• /
• pp.149-159
• /
• 2017

Coastal dunes have many environmental and ecological socio-economic importances; various human activities, however, have impaired their structures and functions over the years. In 2016, environmental survey on coastal sand dune was carried out to report the present status and update the coastal sand dune list in 2001. This research analyzed the survey data in terms of geomorphological and socio-economic aspects. A list of the 189 coastal sand dune and information was updated by province. A 36.5% reduction in coastal sand dune area have been identified for using agricultural land, development area since the approximately 1940-50s. Development area in coastal sand dune covered small area as 5%, the use intensity was relatively hard. Furthermore, the difference by province also showed. Approximately 80% of the development area was concentrated in 20% of total sand dune several sand dune. It is generally accepted that coastal sand dunes were exposed high development pressure. However the result means that the general brief dose not apply for all sand dune. Therefore, characteristics of each sand dune should be analyzed and concerned the diverse management plans.