• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.242-247
• /
• 2003

An experimental study presents characteristics of combustion in a combustion chamber by port deactivation valve for economy and emissions standards. In order to use combustion properties data it is necessary to build some data base, which use cylinder pressure sensor, etc. Port deactivation valve has been developed to satisfy requirement of achieving sufficient swirl generation to improve the combustion. A feasibility and necessity of combustion pressure based cylinder spark timing control has been examined. So, this was obtained the Coefficient of Variation(COV) and the mass-burned(MFB). The characteristics of pressure ratio fraction is similar to that of mass-burned fraction. Using the results of the test, the effects of the combustion chamber can be improved combustion stability by port deactivation.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.59-63
• /
• 2009

This paper presents two dimensional simulation results of an inductively coupled $Ar/O_2$ plasma reactor. The effects of operating conditions on the plasma properties and the uniformity of atomic oxygen near the wafer were systematically investigated. The plasma density had the linear dependence on the chamber pressure, the flow rate of the feed gas and the power deposited into the plasma. On the other hand, the electron temperature decreased almost linearly with the chamber pressure and the flow rate of the feed gas. The power deposited into the plasma nearly unaffected the electron temperature. The simulation results showed that the uniformity of atomic oxygen near the wafer could be improved by lowering the chamber pressure and/or the flow rate of the feed gas. However, the power deposited into the plasma had an adverse effect on the uniformity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.06b
• /
• pp.60-66
• /
• 1998

The horizontal cold chamber pressure die casting produces a variety of net shape, complicate-geometry castings with desired mechanical properties. dimensional tolerance, and surface finish. However, top quality castings can be achieved only when optimal performance of thecold chamber (shot sleeve )and plunger is maintained druing the molten metla injection phase of the process. Unforturately, inreality , shot sleeves deteriorate fast and sometimes fail catastrophically due to incorrect design. These early and unexpected failures of shot sleeves cost die casters money and productiivity. To prevent promature failures of shoe sleeves major faulure mechanisms were investigated. with the aid of analyticla solutions robust design criteria for shot sleeves have been developed. The data directly obtained from failed shot sleeves in the die casting industry for automotive parts, support a strong correlation between design and filures. by applying these design criterial we expected premature faulures of shot sleeves can be avoided in die casting industry.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.11a
• /
• pp.149-154
• /
• 1999

This paper describes a passive safety injection system with free piston Stirling pump working withabundant decay heat in the nuclear reactor during the hypothetical accident. The water column in the tube assembly connected from the hot chamber to the cold chamber in the pump oscillates periodically due to thermal volume changes of non-condensable gas in each chamber. The oscillating pressure in the water column is converted into the pumping power with a suction-and-bleed type valve assembly. In this paper a dynamic model describing the frequency of oscillation and pumping pressure is developed. It was found that the pumping pressure is a function of the temperature difference between the chambers. Also, the frequency oscillation depends on the length of the tube with water column.

• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.29-33
• /
• 2013

Pneumatic system is widely applied in various industry because it have a many advantage(low cost, high safety, etc..). For design of pneumatic system, accurate flow measurement is required. In this study, compressible fluid flow measurement apparatus was designed and built. It uses an isothermal chamber that can approximate isothermal condition. Therefore, it can be measured for flow-rate using pressure response of isothermal chamber. As a result, this apparatus can be measured for sonic conductance and critical pressure ratio of pneumatic components and it required less time and energy than conventional flow meter. The effectiveness of the designed apparatus is proved by experimental result.

• Journal of Korean Society of Forest Science
• /
• v.50 no.1
• /
• pp.25-28
• /
• 1980

The purpose of the this study was to compare the torlent tree to drought among the Pinus koraiensis, Abies holophylla, and Ginkgo biloba. The water relations parameters of leafy shoots were measured by the Pressure chamber technique from August 10 to September 4 in 1980. On the water relations parameters such as original osmotic pressure(${\pi}_0$), osmotic pressure(${\pi}_p$) and relative water content (RWC) at incipient plasmolysis, and Vp/Vo ratio of the volume of osmotic water (Vp) at incipient plasmolysis to total symplasmic water (Vo) basis, the Abies holophylla shoots showed ontogenetically a superior osmoregulation which are closely associated with drought resistance compared with Pinus koraiensis, and the Ginkgo biloba shoots showed the heighest among these three species.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.75-82
• /
• 2004

The allowable exhaust standard has been intensified as a part of the countermeasure to decrease air pollution in the world. As the cars with an alternative fuel starts to get into the spotlight, the cars with low emission has been introduced and exhaust gas regulation forced in this country. These days, LPG vehicles, which infrastructure of fuel was already built up, and CNG vehicles are recognized for alternative fuel cars in this country. In this study, the constant volume combustion chamber was manufactured and used for experiments to obtain the ignition characteristics of LPG fuel and the optimal ignition energy. The experiment measured the combustion characteristics, in regard to the change of combustion variable, and the change of ignition energy. During the combustion of fuel, the maximum temperature inside the combustion chamber is higher when the initial pressure is higher. The burning velocity also seems to have the same characteristic as the temperature. However, the heat flux did not change much with the theoretical correct mixture but the various initial temperature of the combustion chamber. The heat flux got faster and ignition energy bigger as the dwell time of the ignition system expanded. When the dwell time get longer, the ignition energy also increased then fixed. The ignition energy increased as the initial pressure inside the combustion chamber higher. The heat flux got faster as the dwell time expanded.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.867-872
• /
• 2002

A high intensity acoustic test facility is constructed at Korea Aerospace Research Institute (KARI) by 2003. The reverberant chamber of the facility has a volume of 1,228 cubic meters and shall provide an acoustic environment of 152 dB over the frequency range of 25 Hz to 10,000 Hz. The facility consists of a large scaled reverberant chamber, acoustic power generation systems, gases nitrogen supply systems, and acoustic control systems. This paper describes how the basic parameters of a chamber and power generation systems are controlled to meet the requirement of the test. The volume of a reverberant chamber is controlled by the size of test objects and the reverberant characteristics of a chamber. The capacity of acoustic power generation systems is determined by the energy absorption of a chamber and the efficiency of acoustic modulators. Simple math is employed to calculate the required power of acoustic modulators. Moreover, the paper explains how the distribution of sound pressure level at low frequency is checked by analytical and numerical methods.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.5-9
• /
• 2010

In the paper, the dynamic characteristics obtained from hot-firing tests of 1/2.5-scale thrust chamber for 75 tonf-class liquid rocket engine were described. To investigate the dynamic characteristics by engine start transient period and chamber pressure variation, hot-firing tests were performed in the chamber pressures of 30 bar and 60 bar. According to these variations, combustion stability in the combustion chamber was examined.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1354-1359
• /
• 2007

This paper discusses the acoustic performance of simple expansion chamber using computational fluid dynamics(CFD). The CFD model consists of an axisymmetric grid with a single period sinusoid of acceptable amplitude and duration imposed at the inlet boundary condition. The time history of the static pressure is recorded at two points, one in the inlet pipe and one point in outlet pipe. The time history of the static pressure is converted to the frequency domain using Fourier Transform and the transmission loss (TL) of the muffler is obtained from the ratio of the static pressure at the inlet and outlet pipe. The transmission loss of CFD result is compared with that of the computational acoustic analysis using the boundary element method (BEM). There are some differences in two results due to the pressure drop according to the inlet and outlet pipe length. Therefore, the effects of the pressure drop to the transmission loss have to be considered.