• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.49-62
• /
• 2016

In this study, a solid oxide fuel cell (SOFC) system model including balance of plant (BOP) for building electric power generation is developed to study the effect of operating conditions on the system efficiency and power output. SOFC system modeled in this study consists of three heat-exchangers, an external reformer, burner, and two blowers. A detailed computational cell model including internal reforming reaction is developed for a planer SOFC stack which is operated at intermediate temperature (IT). The BOP models including an external reformer, heat-exchangers, a burner, blowers, pipes are developed to predict the gas temperature, pressure drops and flow rate at every component in the system. The SOFC stack model and BOP models are integrate to estimate the effect of operating parameters on the performance of the system. In this study, the design of experiment (DOE) is used to compare the effects of fuel flow rate, air flow rate, air temperature, current density, and recycle ratio of anode off gas on the system efficiency and power output.

• Physical Therapy Korea
• /
• v.4 no.1
• /
• pp.11-19
• /
• 1997

The use of therapeutic ultrasound(US) in humans with malignant neoplasms has been contraindicated in physical therapy practice. Some studies have shown that results after application of US differ according to tumor type and penetration depth. The purposes of this study were to determine the effects of US on melanoma in mice and to determine treatment dosage. Twenty-four female C57BL/6 mice, age 8 weeks. The right flank of all mice was shaved, and a 0.1 ml suspension of cells was injected subcutaneously into the animals' right flank. In this study, 24 subjects were randomly divided into three groups: experimental group 1(n=8), experimental group 2(n=8), control group(n=8). In the experimental group 1, animals received continuous 3 MHZ US treatment, administered at $2.0W/cm^2$ for five minutes. In experimental group 2, animals received continuous 3 MHz US treatment, administered at $1.0W/cm^2$ for 5 minutes. The control group received the same handling as other experimental groups, including rodent chow, water, US gel application but US head pressure without the power turned on. After 10 days treatment, all mice were killed with a potassium solution. Tumors were excised and weighed on an electrical balance and fixed in a 10% neutral buffered formalin solution. Tumor weights were smaller in experimental group 2(0.3838 g) than in the control group(0.6275 g). Tumor weights of the experimental group 1(0.015 g) were smaller than those of experimental group 2. Continuous therapeutic US decreased the weight of subcutaneous melanoma tumors in mice. The treatment dosage($2.0W/cm^2$) we suggest was more effective than earlier studies on decreasing tumor size with ultrasound.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.161-166
• /
• 2003

It is the common features of the integral reactors that the main components of the RCS are installed within the reactor vessel, and so there are no any flow pipes connecting the coolant pumps or steam generators. Due to no any flow pipes, it is impossible to measure the differential pressure at the RCS of the integral reactors, and it also makes impossible measure the flow-rate of the reactor coolant. As a alternative method, the method by the measurement of coolant pump power has been introduced in this study. Up to now, we did not found out a precedent which the coolant pump power is used for the real-time flow-rate calculation at normal operation of the commercial nuclear power plants. The objective of the study is to embody the real-time flow-rate calculation method by the measurement of coolant pump power in an integral reactor. As a result of the study, we could theoretically reason that the capacity-head curve and capacity-shaft power curve around the rated capacity with the high specific-speeded axial flow pumps have each diagonally steep incline but show the similar shape. Also, we could confirm the above theoretical reasoning from the measured result of the pump motor inputs, So, it has been concluded that it is possible to calculate the real-time flow-rate by the measurement of pump motor inputs. In addition, the compensation for a above new method can be made by HBM being now used in the commercial nuclear power plants.

• Human Ecology Research
• /
• v.58 no.4
• /
• pp.539-560
• /
• 2020

This study presents work-family multiple-role planning by female university students as a new approach to worklife balance. Accordingly, this study examines university years as a key time frame during which students establish their career paths. This study integrates the social cognitive career theory and the planned behavior theory to design and evaluate a model that explains the work-family multiple-role planning process; in addition, it develops an optimal model to predict the intentions of female university students in work-family multiple-role planning. This study has conducted a structural survey with 500 female university students. After inspecting the data, the responses of 435 participants were used in the data analysis (SEM) with SPSS 21.0 and AMOS 21.0. The findings include the following. First, suitability of predictive model presents a satisfying fit. The major factors in this study's model (parental support, subjective norms, attitudes toward multiple-role planning, career decision self-efficacy, and outcome expectations) are verified as direct and indirect predictors of the work-family multiple-role planning intent of female university students. Second, the strongest predictive factor for the work-family multiple-role planning intent is the social environment factor (subjective norms), indicating that the influence of social pressure on intent is relatively large. The predictive model formulated under this study's integrated theoretical framework supplements existing research that focused on attitudes toward multiple-role planning as well as provides a more profound theoretical foundation on which work-family multiple-role planning behaviors can be better understood.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.2
• /
• pp.216-224
• /
• 2001

Experiments have been performed to investigate evaporative heat transfer characteristics of R-134a flowing in a small diameter tube. Test section was made of stainless steel tube with an inner diameter of 2.2mm and was uniformly heated by electric current which was applied to the tube wall. The local saturation temperature of refrigerant flowing in a tube is calculated from the measured local saturation pressure by using an equation of state. Inner wall temperature was calculated from measured outer wall temperature, accounting for heat generation in the tube and one dimensional heat conduction through the tube wall. Mass quality of refrigerant flowing in a tube was calculated by considering energy balance in the pre-heater and the test section. Heat flux was varied from 19 to 64kW/$m^2$, and mass flux was chanted from 380 to 570kg/$m^2$s for each heat flux condition. From this study, heat transfer in a small diameter tube is affected by heat flux as well as mass flux for a wide range of mass quality. Heat transfer coefficient in a small diameter tube is much greater than that in medium sized tubes. Test results in this study are compared with Gungor and Winterton correlation, which gives an absolute average deviation of 27%.

• Transactions of the KSME C: Technology and Education
• /
• v.5 no.2
• /
• pp.97-104
• /
• 2017

In this study, we verify the accurate numerical analysis and simplify the perforated plate of inlet and exhaust duct using porous media for the cost reduction and the efficiency improvement of thermal-fluid analysis to evaluate cooling performance of wheel-loader. The flow loss coefficient of the perforated plate is defined by the experiment result. To define analytically the flow loss coefficient of the perforated plate, we calculate the pressure drop of unit-cell and compare to experiment result. Finally, we compare the heat balance test and the simplified simulation result on the inlet and exhaust duct of wheel-loader. After this study, we verify the applicability of the simplified analysis method on the inlet and exhaust duct of wheel-loader. And, foundation which can carry out effectively the evaluation and improvement for cooling performance of wheel-loader is prepared.

• Journal of Pharmacopuncture
• /
• v.12 no.1
• /
• pp.43-51
• /
• 2009

Objective : The purpose of this study is to present the standard for practical application of ginger herbal pharmacopuncture Material and Methods : We refer to ancient literatures and the recent papers for ginger. Conclusions : The following results have been obtained 1. The effect of ginger(Zingiber officinale Roscoe) is to "release exterior", "balance nutrient & defensive qi", "resolve phlegm", "arrest coughing", "warm the lungs". So ginger herbal pharmacopuncture can be applied to treating fever, chilling sign, headchae, snuffle and gasping cough due to cold affection and treating the symptoms like sputum and asthma that be revealed by pulmonary disease. 2. The effect of ginger is to "warm spleen and stomach", "arrest vomiting" "promote normal flow of water". So ginger herbal pharmacopuncture can be applied to treating nausea, vomiting, abdominal distension and diarrhea due to phlegm & dampness and treating edema. 3. The effect of ginger is to eliminate blood stasis. So ginger herbal pharmacopuncture can be applied to treating contusion, blood stasis, sprain and gynecologic disease. 4. Ginger can treat myalgia and pain due to wind-damp and have anti-inflammatory effect in pharmacology. So ginger herbal pharmacopuncture can be applied to treating disease of joint, ligament and muscle. 5. Ginger can resolve phlegm and resuscitate. So ginger herbal pharmacopuncture can be applied to treating unconsciousness. But, treating incipient cardiovascular accident, it needs to call your special attention to the danger of blood pressure increase. 6. In pharmacology, ginger is effective for antitumor, antioxidant effects and activating immunocyte. So ginger herbal pharmacopuncture can be applied to treating broadly varieties of tumor and allergic disease.

• Korean Journal of Community Nutrition
• /
• v.11 no.6
• /
• pp.714-724
• /
• 2006

In an attempt to investigate mothers' perceptions of factors affecting preschool children's food preferences, their policy improving food intake and belief in food selection, in-depth interviews with 30 mothers who had preschool children were conducted in Daegu and Busan. The interviews were tape-recorded and the contents of interviews were analysed by researchers. Most mothers and children liked meats. It was found that children usually disliked vegetables such as onions, carrots, and green onions. Mothers perceived that many factors affected their children's food preferences: mothers' and fathers' food preferences, food offering at meals. mothers' food intake during pregnancy, children's food intake during weaning period, heredity peer pressure, and advertisements on television. Mothers made efforts to improve childrens food intakes in many ways: change of cooking method, emphasizing function of nutrients and food for health, conciliation and enforcement, and comparison to other children. The most affecting belief for mothers in food selection was family members' food preference. Health, balance in nutrient intake degree of food processes food additives, chemicals, convenience, diversity, and economy were also important beliefs to select food. Convenience was especially the primary belief in choosing and preparing children's snacks. Mothers offered frozen dumplings and meat, instant noodles, tuna, and ham for snacks for convenience. These results showed that mothers understood many aspects affecting children's food preference tried to improve children s food intakes and had several beliefs in food selection. We concluded that it is necessary to give information for mothers to make healthy snacks in a short time and chance to learn cooking skills.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1003-1010
• /
• 2013

In this study, a simulation program was developed, which predicts the performance of cold-air forced circulation type air cooled showcase. The showcase has an excellent display effect in addition to preserving the grocery. In the program, the compressor was analyzed using performance data supplied by the manufacturer and the capillary tube pressure drop was analyzed using a homogeneous model. The evaporator and condenser were analyzed by dividing the heat exchangers into small elements, where energy balance and appropriate heat transfer correlations were used. A showcase model with two 3/4 HP compressors, capillary tubes of 1.6 mm inner diameter, a fin-and-tube evaporator and condenser was tested, and the results are compared with the predicted values. It is shown that both evaporation and condensation temperatures are adequately predicted by the program.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.501-508
• /
• 2008

Small injection molded articles such as lens and mobile product parts are usually molded in multi-cavity mold. The problem occurring in multi-cavity molding is flow unbalance among the cavities. The flow unbalance affects the dimensions and physical properties of molded articles. First of all, the origin of flow unbalance is geometrical unbalance of the delivery system. However, even the geometry of the delivery system is well balanced, cavity unbalance occurs. This comes from the temperature distributions in the cross-section of runner. Temperature distribution depends upon injection speed because heat generation near runner wall is high at high injection speed. Among the operational conditions, injection speed is the most significant process variable affecting the filling unbalances in multi-cavity injection molding. In this study, experimental study of flow unbalance has been conducted for various injection speeds and materials. Also, the filling unbalances were compared with CAE results. The dimensions and weights of multi-cavity molded parts were examined. The results showed that the filling unbalances vary according to the injection speeds and resins. Subsequently, the unbalanced filling and pressure distribution in the multi-cavity affect the dimensions and physical states of molded parts.