• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.935-946
• /
• 2000

Elastic-plastic stress analysis has been performed to evaluate the fatigue life of an autofrettaged pressure vessel containing cross-bores subjected to pulsating internal pressure of 200 MPa. Finite element analyses were used to calculate the residual and operating stress distributions of the pressure vessel due to the autofrettage process and pulsating internal pressure, respectively. Theoretical stress concentration factors of 3.06, 2.58, and 2.64 were obtained at the cross-bore of the pressure vessel due to internal pressure, 50%, and 100% autofrettage loadings, respectively. Local stresses and local strains determined from the elastic-plastic finite element analysis were employed to calculate the failure location and fatigue life of the pressure vessel with radial cross-bores, incorporating the low-cycle fatigue properties of the pressure vessel steel and fatigue damage parameters. Increase in the amount of overstrain by autofrettage process moved the crack initiation location from the inner radius toward a mid-wall, and extended the crack initiation life. Predicted fatigue life of the fully autofrettaged pressure vessel with cross-bores increased about 50%, compared to the unautofrettaged pressure vessel. At the autofrettage level higher than 50%, the failure location and fatigue life of the pressure vessel were not significantly influenced by the autofrettage level.

• 한국안전학회지
• /
• 제32권4호
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• 한국공작기계학회논문집
• /
• 제12권2호
• /
• pp.37-43
• /
• 2003

This study makes to flow analysis of computational fluid dynamics(CFD) according to the basic theory of turbulent flow regarding high-pressure injection nozzle. It also makes structural analysis to find out the structural validity of the optimum shape of high-pressure injection nozzle. It divides to two areas such as plunger areas and high-pressure injection nozzle area including plunger.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.541-544
• /
• 2008

Generally numerical analysis of tunnel lining, under dynamic loading condition, performed not considering pore pressure. But if tunnel excavated under the surface of water, such as bottom of the sea, the river bed, tunnel lining can take pore water pressure. It may be different from evaluated numerical analysis not considering pore pressure. Therefore tunnel design should consider effect of water pressure acting on tunnel lining.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.197-202
• /
• 2002

The most common failure of breakwater comes from impact wave pressure generated by intense storms. This impact pressure is 10 folds greater than the pressure generated by normal waves. Therefore, the precise knowledge of magnitude of impact wave pressure applied on breakwater and its structural response is crucial for the economical and safe design. However, presently, a precise analysis of breakwater is restricted by insufficient and incorrect consideration of the effect of soil-structure Interaction. 3 major research areas included in this study are (1) theoretical analysis of impact wave pressure, (2) selection of breakwater structure model (3) soil-structure interaction analysis using limit analysis computer program. Based on this analysis, predicted response of concrete breakwater and probable failure location under wave impact pressure are determined.

• 조명전기설비학회논문지
• /
• 제26권7호
• /
• pp.84-91
• /
• 2012

In this paper, design by magnetic analysis software and proportional control of solenoid for pressure valve for electric pressure cooker is described. The validation of design was proved by 3D finite element analysis results. Also the efficiency of an air ventilation mechanism was considered when pressure was happened by fluid analysis results. The linear proportional control system by AVR was manufactured and its validation was proved by pressure control of solenoid.

• 대한한의진단학회지
• /
• 제15권2호
• /
• pp.159-168
• /
• 2011

Objectives: The purpose of this study is to develop the pulse wave analysis model with the palpation pressure and the skin effect. Methods: The position of pulse diagnosis was modeled with elastic string system. The skin was modeled with the elastic string, the palpation pressure with tension in the string, and the blood vessel pressure with external force on the string. Using the wave equation in the physics, the simplified pulse model was transformed to the mathematical model. Results: To the verification of the model, the effects of the palpation pressure and the skin effect were tested. Conclusions: There was optimal palpation pressure, describing the exact vessel pressure pattern and maximizing the amplitude of the skin displacement. For the optimal condition, the increased palpation pressure was needed with the increased skin thickness. Therefore, the developed pulse wave analysis model showed the good results.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.4694-4699
• /
• 2013

본 논문은 고압세척기의 성능을 향상시킨 제품개발을 위하여 현장에서 사용되는 고압세척기를 분해하여 측정하였으며 실제형상을 3차원 설계프로그램인 CATIA V5를 사용하여 모델링하였다. 또한 모델링된 고압세척기에 대하여 3차원 유한요소해석 프로그램인 ANSYS를 사용하여 유동해석을 수행하였으며 그 결과를 구조해석의 입력 자료로 활용하여 내부압력에 따른 응력, 변형률, 총변형량을 구하였다. 이러한 결과는 새로운 고압세척기의 제품개발에 활용될 예정이다.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5330-5333
• /
• 2013

본 논문은 고압세척기의 성능을 향상시킨 제품개발을 위하여 현장에서 사용되는 고압세척기를 분해하여 측정하였으며 실제형상을 3차원 설계프로그램인 CATIA V5를 사용하여 모델링하였다. 또한 모델링된 고압세척기에 대하여 3차원 유한요소해석 프로그램인 ANSYS를 사용하여 유동해석을 수행하여 내부압력에 따른 유체의 흐름을 구하였다. 이러한 결과는 새로운 고압세척기의 제품개발에 활용될 예정이다.

• 한국기계연구소 소보
• /
• 통권20호
• /
• pp.49-55
• /
• 1990

Filament-Wound composite pressure vessels offer significant weight saving over the conventional metal pressure vessels. S-2 glass/epoxy pressure vessel was designed, fabricated and tested. It was considered, in the analysis that the matrix and the metal liner of FRP pressure vessel shared the internal pressure. The thicknesses of hoop and helical layers were determinded by the computer program developed for the design of FRP/Metal structural pressure vessel. The computer program increased the structural efficiency about 14% comparing with the netting analysis. The experimental measurement on the deformation by internal pressure agrees with the theoretical analysis within the accuracy of 5%.