• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.309-316
• /
• 2017

In injection molding, the quality of an injection molded product varies greatly depending on the molding conditions. Many researche studies have been conducted on the quality analysis of molded parts according to the molding conditions such as injection pressure, injection temperature, and packing pressure. However, there have not been many studies on the V/P switchover timing. It is known that when a large pressure is applied to a cavity in the packing phase, the cavity pressure is most affected by the packing pressure. In addition, depending on the position (timing) of the packing pressure, it can have a direct influence on quality based on the shrinkage and dimensions of the molded parts. In this study, the change in pressure profile in the cavity according to the V/P switchover position is confirmed. A CAE analysis program (Moldflow) was used to simulate and analyze two models using the PC and PBT materials. In order to compare these results with the actual injection molding results, injection molding was performed for each V/P switchover position, and the correlation between simulation and experiment, especially for the shrinkage of molded parts, was evaluated.

• Journal of Advanced Research in Ocean Engineering
• /
• v.4 no.1
• /
• pp.7-15
• /
• 2018

The submarine is an underwater weapon system which covertly attacks the enemy. Pressure hull of a submarine is a main system which has to have a capacity which can improve the survivability (e.g., protection of crews) from the high pressure and air pollution by a leakage of water, a fire caused by outside shock, explosion, and/or operational errors. In addition, pressure hull should keep the functional performance under the harsh environment. In this study, optimal design of submarine pressure hull is dealt with 7 case studies done by analytic method and then each result's adequacy is verified by numerical method such as Finite Element Analysis (FEA). For the structural analysis by FEM, material non-linearity and geometric non-linearity are considered. After FEA, the results by analytic method and numerical method are compared. Weight optimized pressure hull initial scantling methods are suggested such as a ratio with shell thickness, flange width, web height and/or relations with radius, yield strength and design pressure (DP). The suggested initial scantling formulae can reduce the pressure hull weight from 6% and 19%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.590-591
• /
• 2005

Hydrodynamic pressure fluctuations and their roles on the design of hydraulic structures has been the subject of many investigations. The studies showed that turbulent pressure fluctuations may cause serious damages to hydraulic structures. In case of high velocity flows, separation of flow from the boundary also causes the local pressure to drop and as a result, the resultant pressure fluctuations may trigger cavitation. Sever hydrodynamic pressures are also associated with the vibration of structures. Therefore, in this work, experiments were performed to determine the intensity of pressure fluctuations and their distribution along the bed of a ski-jump flip bucket. Experiments were completed on a physical model at the Institution of Water Research of Iran. The results consist of the statistical characteristics of pressure fluctuations, its maximum, minimum, and r.m.s values along the bed of the bucket. The spectral analysis of pressure fluctuations which is useful for the instability analysis of such structures is also provided. It is hoped that the present results will help the designer of such structures.

• 연구논문집
• /
• s.29
• /
• pp.185-194
• /
• 1999

The shape and thickness distribution according to the pressure-time curve were carried out using the FEM and experiment. Also, mechanical properties were investigated. The square cup parts have been formed with pressure-time curve generated by result of analysis. The tensile strength and elongation have been investigated according to applied pressure conditions using the tensile test specimen obtained from the superplastic formed cup. We can use to predict the shape of formed part under the applied pressure using the FEM analysis. In the case of optimum pressure condition, the thickness distribution and mechanical properties were improved. From this study, we can find the important of optimum pressure-time condition. We have investigated about the forming of airplane part and fuel tank for motorcycle. If the applied load used in boundary conditions was appropriate, the simulation result coincides with the formed part. However, it is very difficult to define the pressure condition in complicated shape. Thus, it is need to develop the optimum pressure condition for superplastic forming.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.4
• /
• pp.491-499
• /
• 2009

The determination of response characteristics for pressure sensors is routinely limited to static calibration against a deadweight pressure standard. The strength of this method is that the deadweight device is a primary standard used to generate precise pressure. Its weakness lies in the assumption that the static and dynamic responses of the sensor in question are equivalent. Differences in sensor response to static and dynamic events, however, can lead to serious measurement errors. Dynamic techniques are required to calibrate pressure sensors measuring dynamic events in milliseconds. In this paper, a dynamic calibration using negative going dynamic pressure is proposed to determine dynamic pressure response for piezoelectric sensors. Sensitivity and linearity of sensor by the dynamic calibration were compared with those by the static calibration. The uncertainty of calibration results and the goodness of fit test of linear regression analysis were presented. The results show that the dynamic calibration is applicable to determine dynamic pressure response for piezoelectric sensors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.9
• /
• pp.2909-2915
• /
• 1996

Precise and accurate pressure measurements are obtained using deadweight piston gauges. Pressure distribution and elastic distortion in the piston-cylinder unit are the leading factors in determination of effective area. The distortion depends upon the pressure distribution in the clearance between piston and cylinder and those are coupled each other. Considering the viscosity pressure relation of oil and governing flow equation in the clearance, a new numerical iterative algorithm is developed. The disagreement between the monotonous and sharp pressure profiles is an indication that the pressure profile will be different for each piston and cylinder unit due to material variances.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.92-99
• /
• 1996

The contact pressure in jointed plates was measured by means of an improved ultrasonic technique. In order to get calibration curve, the relationship between contact pressure and ratio of boundary and bottom echo of normal beam probes were obtained for the calibration blocks with various surface roughness. The ratio of boundary and bottom echoes were measured for the upper/under plates locally compressed with uniform pressure, and the distribution of contact pressure was obtaines. The measured pressure has a good agreement with results of FEM analysis. Thus the proposed ultrasonic method in this work is very useful to measure the contact pressure.

• Journal of the Korean Institute of Gas
• /
• v.25 no.5
• /
• pp.37-51
• /
• 2021

The pressure drop phenomenon that occurs when the same flow rate is supplied to the gas regulator was analyzed. The regulator moves the position of the piston through the interaction of the force acting on the upper and lower parts of the piston and the spring tension to release the pressure of a specific range in a specific environment as constant pressure, thereby maintaining the pressure. The flow characteristics and pressure control process of the regulator were investigated through a numerical analysis technique as the volume of the fluid inside the regulator changed. As the gap between the piston and the piston seat decreased, the pressure drop increased and the flow velocity increased. It was verified through numerical analysis that the piston was positioned at 0.12mm under the same conditions as the pressure-flow test (inlet pressure 3MPa, outlet pressure 0.8MPa, flow rate 70kg/h).

• Journal of the Korean Institute of Gas
• /
• v.27 no.1
• /
• pp.38-47
• /
• 2023

In the hydrogen filling process, hydrogen flows by the pressure difference between the supply pressure at a filling station and a storage tank in the vehicle, and the flow rate depends on the pressure difference. Therefore, it is essential to consider the pressure drop of hydrogen occurring during the filling process, and the efficiency of the hydrogen filling process can be improved through its analysis. In this study, the pressure drop was analyzed for a hose, a nozzle/receptacle coupling, a pipe, and a valve in a filling line. The pressure drops through hose and pipe, the nozzle,receptacle coupling, and the valve were calculated by using a equation for a straight conduit, a flow nozzle formula, and a gas flow respectively. In addition, as a result of comprehensive analysis of the pressure drop effect occurring in each component, it was found that the factor that has the greatest influence on the pressure drop in the entire filling line is the pressure drop through the valve. This study can be used to develop a model of the hydrogen filling process by analyzing hydrogen flow including hydrogen filling in the future.

• Journal of Families and Better Life
• /
• v.24 no.5 s.83
• /
• pp.161-174
• /
• 2006

This study examined different individual and parental factors that affect children's achievement motivation. For an analysis, perceived competence, intrinsic locus of control were included in individual variables. For parental variables, parental support and achievement pressure and marital conflict were examined. The sample consisted of 561 fifth and sixth grade children. Statistics and methods used for the data analysis were Cronbach's alpha, Factor analysis, frequency, percentage, Pearson's correlation, and Hierarchical Regression. Several major results were found from the analysis. First, girl's achievement motivation was higher than boys. No age difference was found between fifth and sixth grade. Second, boy's and girl's achievement motivation had a positive correlation with perceived competence, intrinsic locus of control, parental support and achievement pressure but a negative correlation with parental marital conflict. Third, important variables predicting boy's and girl's achievement motivation were perceived academic competence, parental achievement pressure and perceived social competence. Important variables predicting boy's individual and social oriented achievement motivation were perceived academic competence and parental achievement pressure. On the other hand, important variables predicting girl's individual oriented achievement motivation were perceived social competence, perceived academic competence, intrinsic locus of control and parental achievement pressure. Important variables predicting girl's social oriented achievement motivation were parental achievement pressure, perceived academic competence and mother's support.