• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.6
• /
• pp.813-822
• /
• 1998

The microexplosion of a slurry droplet was considered to be caused by the shell formation and the following pressure build-up in the shell which would be promoted by the suppression of evaporation, subsequent superheating and heterogeneous nucleation of liquid carrier. To closely investigate the pressure build-up and the heterogeneous nucleation, a numerical model was introduced by considering the internal temperature distributions with the shell formation, suppression of evaporation and pressure build-up inside. The microexplosion time was estimated by postulating the limit of superheat for heterogeneous nucleation. The simulation yielded a reasonably good agreement with experimental results for Al/n-heptane slurry droplets under various solid loadings.

• Computational Structural Engineering
• /
• v.8 no.1
• /
• pp.85-94
• /
• 1995

The optimum design of the cylindrical shell under external pressure loading is considered. The design variable is a skin thickness of the unstiffened parallel middle body shell. Overall buckling strength and direct stress and displacements constraints are considered in the design problem The optimum design is achieved with one of the standard nonlinear constrained optimization technique. A method for calculating the sensitivity coefficients is developed using the direct differentiation.

• The Journal of Internal Korean Medicine
• /
• v.25 no.3
• /
• pp.473-481
• /
• 2004

Objective : In this study old BCAO rats were observed for effects of 'Dea-Hwang' on brain ischema injury, because risk of stroke increases with age. Method : The brain ischema injury was induced by temporarily closing carotids on both sides in a low blood pressuer state and Dea-Hwang was administered orally to 18 month-old BCAO rats. Results and Conclusions : The ischemically damaged Hippocampus and c-fos and c-jun expression were analyzed by immunohistochemical staining and results are summarized as follows: 1. The c-fos expression after inducing a brain ischema injury in the hippocampus was more inhibited in the dosed group than in the control group. 2. The normalized optical density of c-fos expression was more reduced in the CA1, CA2, and DG areas of the dosed group than in those of the control group. 3. The c-jun expression after inducing brain ischema injury in the hippocampus was more inhibited in the dosed group than in the control group. 4. The normalized optical density of c-jun expression was more reduced in the CAI area of the dosed group than in that of the control group.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.11
• /
• pp.2083-2087
• /
• 2011

The SiC-$ZrB_2$ composites were produced by subjecting a 40:60 vol.% mixture of zirconium diboride($ZrB_2$) powder and ${\beta}$-silicon carbide (SiC) matrix to spark plasma sintering(SPS). Sintering was carried out for 60sec at $1400^{\circ}C$ (designation as TP145 and TP146), $1500^{\circ}C$(designation as TP155 and TP156) and uniaxial pressure 50MPa, 60MP under argon atmosphere. The physical, electrical, and mechanical properties of the SiC-$ZrB_2$ composites were examined. The relative density of TP145, TP146, TP155 and TP156 were 94.75%, 94.13%, 97.88% and 95.80%, respectively. Reactions between ${\beeta}$-SiC and $ZrB_2$ were not observed via x-ray diffraction (hereafter, XRD) analysis. The flexural strength, 306.23MPa of TP156 was higher than that, 279.42MPa of TP146 at room temperature, but lower than that, 392.30MPa of TP155. The properties of a SiC-$ZrB_2$ composites through SPS under argon atmosphere were positive temperature coefficient resistance (hereafter, PTCR) in the range from $25^{\circ}C$ to $500^{\circ}C$. The electrical resistivities of TP145, TP146, TP155 and TP156 were $6.75{\times}10^{-4}$, $7.22{\times}10^{-4}$, $6.17{\times}10^{-4}$ and $6.71{\times}10^{-4}{\Omega}{\cdot}cm$ at $25^{\circ}C$, respectively. The densification of a SiC-$ZrB_2$ composite through hot pressing depend on the sintering temperature and pressure. However, it is convinced that the densification of a SiC-$ZrB_2$ composite do not depend on sintering pressure under SPS.