• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3559-3566
• /
• 2009

Heating and cooling plate are separately used for heating and cooling cast dies for footwear parts. However, this has a disadvantage that it takes a long time to manufacture footwear parts etc.. In the present study, the pipe-inserted cast die for press forming process was proposed to substitute heating and cooling plate. The temperature distribution on the pipe-inserted cast die was analyzed by numerical work using a FEM. And its temperature was measured by LabView. A manufacturing by the pipe-inserted cast die for press forming process was effectively verified, especially in a productivity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.61-66
• /
• 2010

A virtual manufacturing system that is composed of JMatPro, a material modeler and $DEFORM^{TM}$-HT, a finite element package is applied to the hot press forming process: high temperature material properties for each phase such as flow stress, elastic modulus, Poisson's ratio, thermal expansion coefficient, in addition to TTT curve are predicted by JMatPro and taken into $DEFORM^{TM}$-HT to predict the material behavior considering phase transformation and heat transfer simultaneously. In order to verify the accuracy of computation, the residual stress and the springback were compared with the experimental measurements. Both the predicted and measured principal residual stresses and amount of springback were in good agreement. It was also found that the residual stresses generated from hot press forming are not negligible as it has been generally assumed, although the springback deformation is quite small.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.257-260
• /
• 1997

The high precision of the products manufatured by press forming requires the high stiffness of press machines. In this study, the C-frame type press is analyzed to provide the basic idea on the C-frame press design, especially on the frame design. The finite element method is applied for the analysis and the isotropic propertics of the frame material is also considered. The results are summarized in terms of stresses and displacement distributions. Also, the openback angle of the presses is compared with two different models. The CS-150 and ECS-150 models, which are presses model having 150 ton frame capacity relatively and produced by SSangYong precision Co. LTD, are applied for the analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.2
• /
• pp.21-26
• /
• 2000

Flow forming is a chipless metal forming method for axi-symmetric parts, which is more economical. efficient and versatile method of producing parts than the other sheet metal forming process such as stamping or deep drawing. In this study, flow forming process with 1-Roller is applied to produce auto-transmission parts of automobiles which have been produced by Press drawing process so far. It can be known that flow forming process is applicable to the flexible manufacturing system due to the low cost for the establishment and it can be combined with press forming process to promote productivity and to improve the accuracy of products.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.198-201
• /
• 2009

As a way to improve the safety of automotives and to reduce the weight of vehicles, new forming technologies and advanced materials are in high demand in the automotive industry. However, the advanced strength steel has inferior formability and large springback. In order to overcome such drawbacks, the hot press forming process (HPF) has been being applied for forming of automotive sheet parts. In this work, new equipment was suggested to measure unlimited displacement range compared to previous one which was able to measure only up to 10mm displacement range. The external extensometer connected with grips by wire was applied to equipment so that total strain range was measured up to failure also in high temperature. And the finite element analysis was conducted to characterize the mechanical properties of the HPF steel. Finally, the flow curves were represented by utilizing the Johnson-Cook type equation both in uniform and post-uniform deformation regions.

• Transactions of Materials Processing
• /
• v.15 no.6 s.87
• /
• pp.453-458
• /
• 2006

While the die casting has been mainly used to manufacture the magnesium alloy parts, the press forming is considered as an alternative to the die casting for saving the manufacturing cost and improving the structural strength of the magnesium alloy parts. Because the magnesium alloy has low formability at room temperature, forming at elevated temperatures is a necessary condition to obtain the required material flow for press forming. However, the elevated temperature forming does not always guarantee the sufficient formability under the dry friction condition because the surface damage such as scratch or wear may accelerate the material failure. In the present study, the solid-type lubricants such as PTFE, graphite and $MoS_2$ were tested for the square cup warm deep drawing using the magnesium alloy AZ31 sheet. The formability improvement by using the lubricant was examined by comparing the maximum deep drawing depth using the PTFE against no lubricant. The formability difference for the different lubricant was also examined based on the maximum deep drawing depth.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.152-157
• /
• 2009

Titanium alloy sheets have excellent specific strength and corrosion resistance as well as good performance at high temperature. Recently, titanium alloys are widely employed not only aerospace parts but also bio prothesis and motorcycle. But the database is insufficient of the titanium alloy for press forming process. In this study, the effect of temperature on the forming limit diagram was investigated for Ti-6Al-4V titanium alloy sheet through the Hocker's punch stretching test at elevated temperature. Experimental results obtained in this study can provide a database for development of press forming process at elevated temperature of Ti-6Al-4V titanium alloy sheet. From the experimental studies it can be concluded that the formability of Ti-6Al-4V titanium alloy sheet is governed by the ductile failure for the testing temperature below and vice versa neck-induced failure above the recrystalization temperature $0.5T_m$. The formability of Ti-6Al-4V titanium alloy sheet at $750^{\circ}C$ increases about 7 times compared with that at room temperature.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.6
• /
• pp.528-538
• /
• 2011

As a forming method for curved hull plates more efficient than the flame bending, mechanical bending using multi point press forming and die-less forming is discussed in this paper. the mechanical forming is a flexible manufacturing system for automatically forming of hull parts. It is especially suited to varied curved parts. This paper discusses a multiple point pressing machine composed of a pair of reconfigurable punches in order to achieve the rapid forming of curved hull plates using division forming and presents how forming information is obtained from the given design surface. Although the mechanical forming can be efficient in the metal forming, spring back after pressing is a phenomenon which must be carefully considered when quantifying the process variables. If the spring back is not accurately controlled, the fabricated shell plate cannot meet assembly tolerance. This paper describes the principles to calculate the proper stroke of each punch at the divided areas. the strokes are determined by an iterative process of sequential pressing and spring back compensation from an unfolded flat shape to its given design surface. FEA(finite element analysis) is used to simulate the spring back of the plate and the IDA(iterative displacement adjustment) method adjusts the offset of pressing punches from the deformation results and the design surface. The shape deviations of two surfaces due to spring back are compensated by integrated system using FEA and IDA method. For the practical application, It is aimed to develop an integrated system that can automatically perform the compensation process and calculate strokes of punches of the double sides' reconfigurable multiple-press machine and some experimental results obtained with mechanical bending are presented.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.162-169
• /
• 2004

In press forming of sheet metals, the material sheet is usually subjected to very large plastic strain under in-plane stressing. Moreover, the sheet also very often is subjected to out-of-plane compressive force between tools such as the upper and lower dies, the blank holder and the die, and so forth. In this paper, it is clearly demonstrated theoretically that out-of-plane stress may notably raise the forming limit strain and thus it can be effectively utilized to avoid earlier fracture of the sheet in press forming.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.353-356
• /
• 2008

Tool design is carried out for a press forming of a cross member in the rear suspension assembly based on the result of the finite element analysis. The analysis simulates the two-stage stamping process with the initial design and it fully reveals the unfavorable mechanism which develops inferiorities during forming. In this paper, a new design guideline is proposed to modify the process and tool shapes for a single-stage forming process. With the improved tool design, this study fabricates prototypes that satisfy the durability requirement.