• Corrosion Science and Technology
• /
• v.6 no.3
• /
• pp.133-139
• /
• 2007

Nickel powder was coated with aluminum nitrate solution to increase the thermal stability of a porous nickel support and control the nickel content in the Pd-Cu-Ni ternary alloyed membrane. Raw nickel powder and alumina coated nickel powder were uniaxialy pressed by home made press with metal cylindrical mold. Though the used nickel powder prepared by pulsed wire evaporation (PWE) method has a good thermal stability, the porous nickel support was too much sintered and the pores of porous nickel support was plugged at high temperature (over $800^{\circ}C$) making it not suitable for the porous support of a palladium based composite membrane. In order to overcome this problem, the nickel powder was coated by alumina and alumina modified porous nickel support resists up to $1000^{\circ}C$ without pore destruction. Furthermore, the compositions of Pd-Cu-Ni ternary alloy membrane prepared by magnetron sputtering and Cu-reflow could be controlled by not only Cu-reflow temperature but also alumina coating amount. SEM analysis and mercury porosimeter analysis evidenced that the alumina coated on the surface of nickel powder interrupted nickel sintering.

• Nuclear Engineering and Technology
• /
• v.52 no.8
• /
• pp.1714-1723
• /
• 2020

This study aims at characterizing the rheological properties of uranium oxide powders for nuclear fuel pellets manufacturing. The flowability of these powders must be compatible with a reproducible filling of press molds. The particle size distribution is known to have an impact on the rheological properties and fine particles (<100 ㎛) are suspected to have a detrimental effect. In this study, the impact of the particle size distribution on the rheological properties of UO₂ powders was quantified, focusing on the influence of fine particles. Two complementary approaches were used. The first approach involved characterizing the powder in a static state: density, compressibility and shear test measurements were used to understand the behavior of the powder when it is transitioned from a static to a dynamic state (i.e., incipient flow conditions). The second approach involved characterizing the behavior of the powder in a dynamic state. Two zones, corresponding to two characteristic behaviors, were demonstrated for both types of measurements. The obtained results showed the amount of fines should be kept below 10 % wt to ensure a robust mold filling operation (i.e., constant mass and production rate).

• Journal of Korea Foundry Society
• /
• v.5 no.3
• /
• pp.47-51
• /
• 1985

FMC(FULL MOLD CASTING)법(法)이란 발포 polystyrene모형을 사용하여 조형후, 주형으로부터 모형을 발형치 않은채, 용탕을 주입하여 주물을 제조하는 방법을 말한다. 합성수지 발포체를 주조용(用) 모형의 재료로써 사용하는 방법은 1956년 미국의 슈로이어(H. F. Shroyer)에 의하여 발명되었으나 이것은 실제 주조에 응용하기에는 여러 곤란한 문제가 있어, 단순히 착상에 그치고 공업적으로 적용할 수 있는 기술을 확립치는 못하였다. 그후 서독 아헨대학교수로서 당시 발포폴리스티렌을 포함하는 각종단열재 제조회사 G+H 사(社)의 A. Wittmoser에 의하여 1962년에 처음으로 공업적으로 이용되어, 현재 서독, 미국, 일본등 유럽전역에서 응용되고 있다. 당사(當社)는 1977년6월 5일 첫 가동된 이후, 동(同)그룹 사(社)인 현대자동차로부터 자동차금형 (Press Die)주조를 FMC법(法)으로 생산하여 달라는 요구를 받고, 그해 12月부터 개발시험에 착수하여 이듬해 6월(月)부터 본(本) FM주조를 적용하여왔다. 그러나 1) 폴리스티렌 모형의 주입시(時) 부(不)기화 잔유물에 의한 주물표면결함 2) 도형제 박리 현상에 의한 표면결함 3) 주입시(時) 다량의 매연발생 및 4) 조형시(時) 모형의 변형에 의한 칫수결함 등의 문제가 대두되어 품질면에서는 1982년6월(月)에 와서야 어느정도 정상궤도에 도달하여 본격적인 FM 생산을 해오고 있는 중이다. 여기서 그동안 당사가 경험한 대형주물 (자동차금형:$1{\sim}10$톤/개)에 있어서의 FM 주조법의 적용사례를 본지(本誌)를 통하여 간단히 소개하고자 한다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.30-37
• /
• 2017

Weight reduction of the wheel is exerts a great influence on the running performance of the vehicle, a lot of research for a lightweight aluminum wheels progress. In order to select the molding conditions through the experiment on the carbon fiber prepreg molding process based on the design of the mold for manufacturing the carbon wheel using the carbon fiber pressure forming method, the carbon wheel molding process using the Taguchi method And to produce prototypes based on the results.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.57.2-57.2
• /
• 2010

대표적인 투명 전극 재료indium tin oxide(ITO)의 경우, 우수한 투과성과 낮은 면저항을 기반으로 차세대 디스플레이용 전극으로 각광 받고 있다. 하지만 제조 단가가 높으며 brittle 하여 유연 디스플레이에 적용이 어려우며 대면적 제조가 어렵다는 단점이 있어 이를 대체할 수 있는 새로운 물질이 필요한 실정이다. 대표적인 후보 물질로는 탄소 육각형이 서로 연결된 관 형태인 탄소나노튜브가 있으며 뛰어난 전기 전도도와 물리적 특성을 투명 전극에 적용하기 위한 연구가 활발히 진행 중이다. 본 연구에서는 탄소나노튜브 투명 전극 제조 시 잔여 분산제 제거 및 doping의 효과를 위해 수행되는 산처리 공정을 하지 않고 투명 전극의 특성을 향상 시키는 연구를 진행하였다. 제작된 박막에 압력을 인가하여 탄소나노튜브 네트워킹의 향상과 두께의 감소를 얻을 수 있었다. 실험에 사용된 탄소나노튜브는 아크 방전 공정으로 합성된 2nm의 single wall 탄소나노튜브이며 이를 분산제인 sodium dodecyl sulfate(SDS)에 분산하여 용액형태로 제작하여 사용하였다. 분산제를 제거하기 위해 탈이온수를 사용하였으며 고분자 mold를 사용하여 압력을 인가하여 그에 따른 전기적, 광학적 변화를 관찰하였다. 제조된SWCNT 박막은 four point probe measurement를 이용하여 sheet resistance를 측정하였고 UV-vis를 이용하여 투과도와 반사도 등의 광학적 특성을 측정하였다. 박막의 표면은 field emission scanning electron microscope (FESEM)과 Atomic force microscope(AFM)를 이용하여 관찰하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.22-26
• /
• 2010

Recently, due to the tremendous growth of media technology, demands of the aspheric glass lens which is a high-performance and miniaturized increase gradually. Generally, the aspheric glass lens is manufactured by Glass Molding Press (GMP) method using tungsten carbide (WC) mold core. In this study, the thermal deformation which was occurred by GMP process was analyzed and applied it to compensate the aspheric glass lens. The compensated lens was satisfied that can be applied to the actual specifications.

• Fashion & Textile Research Journal
• /
• v.6 no.5
• /
• pp.648-654
• /
• 2004

The purpose of this study was to develops of brassiere pattern for middle school students (15 ages ${\mp}$ 3). In order to design a brassiere pattern, the body surface shell was used as the basic pattern. The foundation pattern and the four-piece brassiere pattern with wire were designed and sewed. The results of this study can be summarized as follows. 1. The foundation pattern of the size 75A was proved proper for the body by the wearing tests. Each angle and length of the parts on the base line of the breasts played an important role on setting the pattern. 2. As based on the body surface shell extracted from a plaster mold, the cups of brassiere pattern were applied to the body surface shell, and full side stretch -wings were applied to 8% reduced body size. 3. As the result of the wearing test, the excellence of the experimental brassiere was recognized objectively, with high marks in all the items of clothing compensation, body motion, clothing pressure and breasts growth. The experimental brassiere was covering the whole breasts to cope with change according to breasts growth, It was designed to support the breasts firmly, not to press the middle part of them. Simultaneously, this has the advantages that satisfy a characteristic of a figure and the purpose of putting it on.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.61-66
• /
• 2008

The hydraulic system have been used much in a heavy machine which high power source is desired. In the case of the heavy press machine and the injection molding machine, the use of the hydraulic power is essential especially for increasing productivity and getting the good products. Because the hydraulic circuit is very complex and the system parameters are uncertain, the development of the simulation model for hydraulic system is not easy in the heavy machine. In this case, Many researchers have used a commercial program for analysis and development in a major field of study. In this paper, the aim is to develop the simulation model of the hydraulic system with various commercial program for trajectory tracking. And adaptive control method is applied to the simulation model for the trajectory tracking of a cylinder motion. Load on the cylinder is modeled in ADAMS program, the hydraulic circuit including pump, spool valve and cylinder is modeled in AMESim program and a controller is designed in MatLab/simulink program. The suggested model is applied for the tracking of a cylinder motion, and through computer simulation, its trajectory tracking performance is illustrated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.2
• /
• pp.91-96
• /
• 2014

Aspheric lenses used in the thermal imaging are typically fabricated using expensive single-crystal materials (Ge and ZnS, etc.) by the costly single point diamond turning (SPDT) process. As a potential solution to reduce cost, compression molding method using chalcogenide glass has been attracted to fabricate IR optic. Thermal deformation of a molded lens should be compensated to fabricate chalcogenide aspheric lens with form accuracy of the submicron-order. The thermal deformation phenomenon of molded lens was analyzed ant then compensation using mold iteration process is followed to fabricate the high accuracy optic. Consequently, it is obvious that compensation of thermal deformation is critical and useful enough to be adopted to fabricate the lens by molding method.

• Steel and Composite Structures
• /
• v.10 no.3
• /
• pp.245-260
• /
• 2010

In this paper, experimental and theoretical investigations on the response and collapse of 310 stainless steel tubes with different diameter-to-thickness ratios subjected to cyclic bending are discussed. The tube-bending device and curvature-ovalization measurement apparatus were used to conduct the experiment. The endochronic theory combined with the principle of virtual work and finite element software, ANSYS, were used to simulate the moment-curvature and ovalization-curvature relationships. It is shown that although the two methods lead to good simulation of the moment-curvature relationship, the endochronic theory combined with the principle of virtual work has the better simulation of the ovalization-curvature response when compared with experimental data and the simulation by ANSYS. In addition, the theoretical formulations proposed by Kyriakides and Shaw (1987) and Lee et al. (2001) were used to simulate the controlled curvature-number of cycles to produce buckling relationship. It is shown that the theoretical formulations effectively simulate the experimental data.