• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1043-1044
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.561-562
• /
• 2011

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.122-129
• /
• 2008

This paper deals with precise positioning of a high-speed positioning stage without inducing residual vibration by using an input shaping technique. Input shaping is well known to be a very effective tool for suppressing the residual vibration of flexible structures. However, the ordinary input shaping for positioning stages is designated mostly for velocity regulation, not for the residual vibration at the target position. The main difficulties in implementing input shaping along with precise positioning are the time delay caused by the servo system characteristics and the s-curve feature often employed in some motor controllers. This paper analyzes the dynamic responses of a single-mode-dominate stage system subjected to input shaping. A theoretical model is developed io investigate the nature of system. In order to overcome the difficulty, this paper proposes an improved input shaper based on modified command profile generation. The proposed method is proved effective through experiments and simulations.

• Smart Structures and Systems
• /
• v.1 no.1
• /
• pp.13-27
• /
• 2005

Simultaneous precision positioning and vibration suppression of a reciprocating flexible manipulator is investigated in this paper. The flexible manipulator is driven by a multifunctional active strut with fuzzy logic controllers. The multifunctional active strut is a combination of a motor assembly and a piezoelectric stack actuator to simultaneously provide precision positioning and wide frequency bandwidth vibration suppression capabilities. First, the multifunctional active strut and the flexible manipulator are introduced, and their dynamic models are derived. A control strategy is then proposed, which includes a position controller and a vibration controller to achieve simultaneous precision positioning and vibration suppression of the flexible manipulator. Next, fuzzy logic control approach is presented to design a fuzzy logic position controller and a fuzzy logic vibration controller. Finally, experiments are conducted for the fuzzy logic controllers and the experimental results are compared with those from a PID control scheme consisting of a PID position controller and a PID vibration control. The comparison indicates that the fuzzy logic controller can easily handle the non-linearity in the strut and provide higher position accuracy and better vibration reduction with less control power consumption.

• Journal of Korean Society for Geospatial Information Science
• /
• v.13 no.1 s.31
• /
• pp.37-43
• /
• 2005

GPS has been increasingly used in high precision positioning thanks to rapid advances of GPS technology. In order to acquire precise coordinates from GPS, it is important to solve accurately integer ambiguity inherent in GPS signals. The previous methods to solve this ambiguity were mostly based on multi-epoch data but recently a method based on single-epoch data has been developed. In this study, we selected three sets of software based on these methods, applied them to GPS baseline processing, and analyzed the experimental results. From these analyses, we have also verified the potential of their uses in real time precision positioning.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.164-169
• /
• 2001

The active magnetic bearing has many advantages - an active positioning, no contact and lubrication free motion - and is widely used in high precision motion stages. But, the conventional magnetic bearings composed of electromagnets only are power consuming due to their bias current and have the excessive heat generation, which can make the repeatability of the positioning system worse. To overcome this drawback, we developed a novel permanent magnet (PM) biased linear magnetic bearing for a high precision magnetically levitated stage. The permanent magnets provide a bias flux and generate a bias force, and the electromagnet increases or reduces a flux of the permanent magnets and gives a levitation force. This paper presents a theoretical magnetic circuit analysis, FEM analysis and experimental data from the 1-DOF tests, and compares the theoretical power consumption of the electromagnetic bearings and the PM biased linear magnetic bearings. The PM biased linear magnetic bearing presented in this paper gives better load capacity but lower power consumption than a conventional electromagnetic bearing and will be adopted in our 6-DOF high precision linear positioning maglev stage.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.23-33
• /
• 2012

This paper is a study on precise point positioning using global navigation satellite system. This paper studies inherent barriers of global navigation satellite system such as increase in shadowed areas and positioning errors when signals cannot be received due to various environmental factors. It analyzes performance of various receivers, changes in number of satellite and DOP(Dilution of Precision) following changes in environment such as center of a road, side of a road, residential area, high building, and alleys. It also studies changes in positioning error. The objective of this study lies on understanding the range of positioning error following changes in environment and the cause of error, and enhancing the reliability and safety of the global navigation satellite system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.773-776
• /
• 2005

In this paper, For improving the positioning accuracy of hydrostatic table, relationship between temperature of atmosphere and thermal characteristics of hydrostatic table is analyzed, and influence of thermal characteristics on positioning accuracy is also analyzed experimentally. From the experimental results, it is confirmed that positioning error and repeatability is $0.21{\mu}m\;and\;0.18{\mu}m$ when the laser scale which has $0.01{\mu}m$ of resolution is used as feed-back unit. and also confirmed that thermal deformation of scale and supporter, which occurs by the temperature variation of atmosphere, works as limit of repeatability in long time operation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.175-178
• /
• 2000

An aerostatic stage has frictionless behavior, so it has a advantage of investigation into positioning characteristics. A one-dimensional aemstatic ceramic stage with ballscrew driven and laser scale feedback system is manufactured. aiming at investigating positioning characteristic of aerostatic stage, especially position error and repeatability, we analyze positioning behavior with other factors such as angular error, temperature. Experimemal results show that the aerostatic stage has a l0nm micro step response. Comparing experimental results and calculated abbe's error, we confirm that mean of position error is owing to angular error. And, also we confirm the temperature is dominant factor of repeatability in ten nm order.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.137-144
• /
• 1998

For a model system consisted of four pneumatic cylinders with strokes of 10, 20, 40 and 80 mm, investigation was carried out experimentally and numerically about the reliability of system with elastic and viscous load. The elastic load affects the performance of each cylinder in cylinder series, and changes the time lag and the velocity of the piston which makes the positioning control rather difficult. Taking the effects of the elastic load into consideration, positioning can be carried out comparatively smoothly by only adjusting the driving timing. The effect of a viscous load reduces the vibration of each moving body in the cylinder series and also reduces the over-travelled distance which happens when several cylinders move at the same time. For reasons, a positioning with a viscous load can be relatively smoothly carried out even without the timing control.